Question about Mazda Cars & Trucks

Open Question

Torque setting for a mazda 6 ts2 diesel 2004 - Mazda Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: mazda 6 timing marks

You are all fuckin thick. ask a question on here and get answers like this ********

Posted on Nov 06, 2008

  • 9 Answers

SOURCE: mazda 6 diesel wont start

Have you run the car without fuel? There must not be any air in the fuel line... Blead the fuel line of air and try to start it. There should be bleader screws under the hood....

Posted on Jun 13, 2009

bonedivers
  • 1140 Answers

SOURCE: 2004 Mazda 6 stuck in Park?

Cable broke? Would still start. Does shifter move at all?

Posted on Jan 30, 2010

  • 608 Answers

SOURCE: mazda 6 2o diesel replaced turbo new unit same

There is a oil drain return from the turbo charger to the sump. If the sump oil level covers the outlet into the sump, oil will build excess pressure tin the turbo causing the sealing rings to leak oil in to the intake manifold. This would cause smokey exhaust and loss of oil. Try this. Drain the sump completely, refill with the exact quantity of oil to Mazda spec. Dip the oil and if the new oil level is lower than the full mark on the dipstick, you have found the cause of the problem. Mark this new level with a scriber or file and fill only to this new level. Hope this is the solution.

Posted on Mar 23, 2010

  • 1 Answer

SOURCE: I have a mazda 6 2 litre diesel eating oil, what

Mazda say that if your Mazda 6 consumues less than a litre every 900 miles then it within tolerance.
However these cars have a complicated induction mechanism controld by lots of diffrent vacume pots that are inturn controlled by servos, when any one of these becomes faulty the pressure balance between the exhaust side of the turbo and the inlet side becomes inbalanced, resulting in oil being forced through the turbos bearings. Its that simple lol!
The first thing I would check would be the swirl control valve, In the inlet manifold, This gets fouled up by the exhaust gases getting recycled by the egr valve(exhaust gas recycler)
Sooty deposits mix with oil coming from your turbo and jam it closed restricting the amount of air into the engine, and reducing power as well as creating black smoke from your exhaust.
So my advice would be to get your egr valve proffetionally blanked off, and have your induction system checked over.
Hope this helps as I am sure this is a very common problem!

Posted on Sep 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MAZDA HEAD TORQUE


start in the middle and work around to the outside..set to 45 then go in incruments of 5 on each round..up to 85

Jan 07, 2014 | Mazda Cars & Trucks

1 Answer

Cant find torque settings for a mazda XA 3.0L 4 cylider


older mazda diesels e3000 (3litre) were often rebadged to ford traders I have a book on that diesel (E3000)and if it is the same I can give you the specs but to find you again I will require you to send a reply comment. It may take me some time to dig up the book so if you will reply comment I will send you what I have

Dec 25, 2013 | Mazda B-Series Truck Cars & Trucks

1 Answer

What are mazda 6 wheel bearing torque specification


What is the front axle torque on a 2004 Mazda 6

Mar 17, 2012 | 2004 Mazda 6

2 Answers

Please describe cylinder head torque secuense mazda wl DIESEL 2007 turbo 2.5


The head torquing sequence is as below:-

9....5....1....3....7
Front
10...6....2....4....8

Carry out the sequence at least three times, once at about half the torque value and then at least twice at the full value.

Feb 14, 2011 | Mazda B-Series Truck Cars & Trucks

1 Answer

I am running a mazda 6 TS2 2004 model. 2 amber lights came on my dashboard this morning. One of a car skidding and the other of an engine.


these are traction control and service engine. first look for a button or switch for the traction then have an obd2 scan done. you can scan it first this may tell you about the traction. your local auto zone or advance auto does this service for free if you don't have access yourself.

Jan 17, 2011 | Mazda MAZDA6 Cars & Trucks

1 Answer

I need a Denso SCV (suction control valve) for my Mazda 6 diesel pump. Part number RFY313SMOA.


you can buy it in SURESTART DIESEL INJECTION SERVICES address Shaw Lne Industral Estate, Doncaster (01302) 340467

Mar 09, 2010 | 2004 Mazda 6

1 Answer

My mazda 6 ts2 seems to have 2 headlight bulbs that dont do anything any ideas


Steve, have you heard of spare bulbs. So that you do not lose/misplace them after cleaning the car, Mazda has placed them where they are required. Right in the headlights.

Dec 23, 2009 | 2006 Mazda 6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...