Question about Cars & Trucks

1 Answer

We have2005 coopers and the engine is back firing andthen no power.We changed the coil pack-injectors- plugs-wires and nothing on the diagnostics.Please help if some one has had this problem before

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Cars & Trucks Master
  • 1,038 Answers

  1. check the emissions. Running lean, injectors or plugs not firing at the exactly right times will do the same thing. That will show up in an emissions test (smog). Then u have a starting point.

Posted on Aug 11, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: engine code p0307 cylinder #7 misfire

It could be carbon deposits on valve seats keeping valves from totally closing. You can try getting you a can of motorcraft PM3 top end engine cleaner and get engine up to operating temp then remove one of the small vacuum lines from the intake and draw the contents of the can slowly into the engine.After you have drawn in the contents shut engine off and let it soak for about 45 minutes then crank it back up and let it run until it clears. Now it will smoke like a forrest fire while you are doing this so don't be alarmed,just tell the neighbors you are spraying for mosqitos.This may cure the problem. If not you may be looking at a valve job.
This can be verified with a compression test if this is what is causing it.

Posted on Feb 05, 2009

ButtFuzz
  • 463 Answers

SOURCE: my 2000 v8 toyota tundra suddenly lost power

Does this motor have the equivalent of crank-trigger ignition? If so, is the sensor A-OK?

Posted on Mar 02, 2009

  • 14036 Answers

SOURCE: 2000 Kia Sephia p0303 code engine misfires

do a compression test. cylinder 3 could have a bad valve lifter or valve.kia sephia dont have push rods.it have a bucket type followers.a intake leak to that cylinder can also cause misfire problems.

Posted on Jun 06, 2009

fingaz22
  • 1068 Answers

SOURCE: 2004 ford ranger edge has blinking check engine

have the crank sensor check for erratic operation. if you have done all of that then there is nothing else. and they way the computer knows it is misfiring (if it is) false code maybe and could be bad crank sensor. good luck

Posted on Oct 25, 2009

  • 2 Answers

SOURCE: 1997 Dodge Intrepid cranks over won't fire

I have this same NO START problem...
Began with tach giving readings not exceding 1200 rpm with strange 4000 + spikes.. Cruse control would not turn on or off at times and indicator light would only work sometimes..Had several episodes of excessive cranking to get it to start.. Stalling out while driving and even at freeway speeds.. Pulling the negative cable for 10 min. allowed it to start although with lots of cranking and put it in limp mode which required another computer reset to get out of.. Had thrown error codes related to cam and crank sensors which were replaced along with coil and manifold temp sensors.. Had the 9 volt power to sensors when key was on but the check engine light does not stay on with all the other idiot lights..
I wish people who respond would read the post first..
Original post states,
Cranks,No spark,No fuel pump run, changed some sensors ect...
If it cranks it ain't the neutral safety switch, starter or battery!! WAKE UP!!
Seems the computer is not turning on the coil, injectors or fuel pump for a reason.. Find that reason and you will find the solution to the problem.. Seeing as that the computers logic states are a dealer secrete the poster as I have changed many parts in blind hope that it will fix the problem.. Relays, sensors and ecu computer.. Did a visual check of all harness potential wear spots like where it crosses over the power rack..
Could it be in the wiring harness inside the dash??
Could it be a bad ground??
Can an alternator that has failed cause the computer not to start??
Can a bad oil pressure sensor cause the computer not to start??
Can signal loss from the TCU or BCU to the ECU cause this??
Is there an undocumented kill if the ECU thinks it was in an accident??
I can ground the relay line from the ECU and the fuel pump runs and pressures up and the other relays turn on as well..
This crank but no start problem seems to be common with a lot of 1994-2001 Dodge and Chrysler owners.. All these systems have become interlaced with undocumented safety features that baffle the DIYer..If you have seen this and have fixed it PLEASE RESPOND!!!!

Posted on May 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

2004 Grand Cherokee (4.0)intermittent #1 cyl misfire and #1 injector control circuit fault (3 wks). Problem began after changing spark plugs. Replaced: coil pack, 6 injectors, & Bank #1-#2 O2 sensors.


I worked on one with the same issue. Ended up being the harness burned at the rear of the engine on the exhaust. Burned wires going to coil pack and shorted when I moved the wires to the coil packs.

Feb 22, 2017 | Jeep Cars & Trucks

1 Answer

What is the Wire Order with distributor?


theres no distributor and the firing order for your 3.8 is 1-6-5-4-3-2-the following link shows the coil pack
Buick General Motor 3800 V6 Engine Firing Order DIS IDI ignition timing 3.8 Buick Engine Coil Pack Firing Order Spark Plug Wire Location Which way do the spark plug wires go on & what cylinder is what?
.
For the Buick V6 231 3.8 liter turbocharged engine:
.
Answers!
.
Firing order:
1 - 6 - 5 - 4 - 3 - 2.
.
Spark plug wire location on coil pack:
.
Closest to the back of the car, left to right: 1 - 5 - 3.
Closest to the front of the car, left to right: 4 - 2 - 6.
.
Spark plug wire location on engine:
.
drivers side, front to back of car: 1 - 3 - 5.
passenger side, front to back of car: 2 - 4 - 6.
.----and this link shows the coil pack to cylinders
.
3 8 Buick Turbo Engine Coil Pack Firing Order Spark Plug Wire Location

Aug 15, 2015 | 1987 Buick Regal

1 Answer

Eml light warning is on and the 2006 Mini Cooper S lost power, the car also had a misfire (P0303) . I replaced the spark plugs, wires and coil pack. Problem still here,


misfires are also caused by low fuel pressure injector electronics faults and faulty injector tips . Replacing plugs is half the fix

Aug 10, 2014 | 2006 Mini Cooper S

1 Answer

2002 tahoe check engine light #8 misfire code


Fuel injectors only receive power on one wire. The other wire is grounded by the PCM. That's what fires the injector. If could be the PCM, but most of the time it's a cam or crank sensor.

Jun 27, 2017 | Chevrolet Tahoe Cars & Trucks

1 Answer

MY 04 KIA SEDONA KEEPS SAYING MISFIRE IN CYLINDER 1 AFTER I'VE CHANGED THE WIRES, PLUGS, COIL PACKS 2X, ALL 4 LIFTERS AND THE FUEL INJECTOR. WHY? AND WHAT AM I DOING WRONG? THANK YOU IN ADVANCE.


Fire it up at night and look for arcing in the dark. It may also be nothing more than number 1 plug wire misrouted in a way that inductively picks up energy from one of the other coil packs or cylinders. It should cross other plug wires only once.

Dec 27, 2011 | Cars & Trucks

1 Answer

I have an 2002 buick century that has a iginition miss. We have changed the spark plugs, iginition wires, coil pack. It first came back with a miss fire number 2 cyclinder. The coil pack was changed. Now...


double check plug wires to be sure they go to the right cylinders. After that i would check fuel injectors
You need a listening device and listen for metallic clicking sound. Bad injectors will be silent and they do cause the same miss

Apr 21, 2010 | 1997 Buick LeSabre

1 Answer

95 aspire sputters and back fires when you try to accelerate , changed fuel filter, fuel pressure is fine, new mass airflow sensor


Check spark in each cylinder. You may have a bad plugwire or coil pack. Make sure fuel is spraying from every injector.
You can remove one plug at a time, plug it back into the plug wire and lay it on top of engine block, have someone else turn motor over and you can view plug to see if it is sparking. Do this to each plug. If you have one or two plugs not firing, you may have bad coil pack.

Aug 24, 2009 | 1997 Ford Aspire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...