Question about Cars & Trucks

Open Question

Headlight adjustments - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where do I find the horizontal adjuster?


MAKEandMODEL needed to help you .

Nov 26, 2015 | Cars & Trucks

2 Answers

How do u adjust headlghts on 1991 gmc seirre


adjustment is on the top of the light and the side.

Jun 22, 2014 | 2003 GMC Sonoma Extended Cab

1 Answer

How do you remove the headlight assembly on 1995 ford f250?



  • 1.
    Remove the two upper screws from the headlight housing, using a Phillips screwdriver.
  • .
    Locate the two lower retaining nuts inside the engine compartment at the bottom of the headlight housing. Remove the nuts using a ratchet, extension and socket.
  • Separate the turn signal and marker light assembly from the front grill. Rotate the bulb holders counterclockwise and pull them out of the assembly. Set the assembly aside.
  • Unplug the headlight bulb connector from the bulb. Rotate the retaining ring counterclockwise one-eighth turn and remove it from the housing. Pull the headlight bulb straight back and out of the housing. Do not rotate the bulb during disassembly.
  • Lift up on the headlight housing retaining clips to unsnap them from the headlight housing vertical adjuster studs.
  • Locate the horizontal adjuster at the outer bottom corner of the headlight assembly inside the engine compartment. Loosen the horizontal adjuster until it is free of the adjuster nut.
  • Remove the headlight housing from the vehicle.
Installation
  • Install the headlight housing in the front grill.
  • Engage the horizontal adjuster screw with the adjuster nut and screw it partially in.
  • Snap the headlight housing clips on the vertical headlight adjuster studs.
  • Insert the headlight bulb into the headlight housing, flat side up. Slightly rotate the headlight bulb to engage the grooves in the light with the alignment tabs in the back of the housing. Install the retaining ring on the bulb. Plug in the headlight bulb connector.
  • Install the bulb holders in the turn signal and marker light assembly. Install the assembly in the grill. Install the two upper screws, using a Phillips screwdriver. Install the two lower retaining nuts, using a ratchet, extension and socket.
Headlight Aiming
  • Pull the vehicle to within a few inches of a blank wall, on a flat surface. Apply two strips of tape to the wall vertically to mark the centers of the headlights. Apply a strip of tape to the wall horizontally to mark the center of the headlight height. Back the vehicle up 25 feet in a straight line.
  • Turn the headlight low beams to the "On" position.
  • Adjust the vertical headlight adjusters until the high-intensity zone of the light pattern is two inches below the horizontal mark on the wall.
  • Adjust the horizontal headlight adjusters until the high-intensity zone of the light pattern is two inches to the right of the vertical headlight marks on the wall.

Nov 08, 2012 | Cars & Trucks

1 Answer

How do i adjust my headlights?


  • Always adjust lights with optical headlight aimer VAS 5107, using detailed aiming procedure and specifications
  • Low and high beams are adjusted simultaneously.
98971520



Left headlight (adjustment screws for right headlight are mirror image):
1 - Lateral adjustment 2 - Height adjustment
  • Access adjustment screws through hole in lock carrier (Phillips head or socket head).
  • Turn the adjusting screws for lateral adjustment -1- and height adjustment -2- until the correct setting is achieved.
NOTE: Where equipped, ensure equal movement/function of headlights during automatic headlight range adjustment.

Oct 19, 2010 | 2001 Volkswagen Passat

1 Answer

2007 maxima headlight adjustment


According to Autozone.com:

Headlight Adjusting Screw Operation:Used to adjust headlight beams up or down and left or right, it's located above and to the side of light behind the headlight retainer.













Oct 15, 2010 | 2007 Nissan Maxima 3.5 Sl Sedan

1 Answer

Headlight adjustment


Used to adjust headlight beams up or down and left or right, it's located above and to the side of light behind the headlight retainer.

Apr 07, 2010 | 2007 Nissan Altima 3.5 Sedan

1 Answer

White plastic bracket holding headlight


headlight bracket, headlight adjuster, or headlight adjuster bracket

Mar 28, 2010 | 1994 Toyota 4Runner

2 Answers

Headlight adjustment screws


They will probably be inset adjacent to the headlight. You'll find a horizontal and a vertical adjusting screw, with small springs behind them. Some cars come equipped with a small level (like a carpenter's level) attached to the top of the headlight under the hood to help you get the correct adjustment.

Nov 12, 2009 | 1992 Dodge Dakota

1 Answer

AUDI A4 2003 1.9TDI HOW TO ADJUST THE HEADLIGHT


There are two adjustment points (screws). For example left headlight: you will see one point near the end of left wing, at bottom side through a wing hole. This is for vertical plane headlight beam adjustment (up-down). Another one point is against water radiator side. This is for horizontal plane headlight beam adjustment (left-right).
Please Rate my Response! Thanks!

Jul 13, 2009 | 2003 Audi A4 Cabriolet

1 Answer

Can't adjust 2004 Ford Expedition headlight


I had a similar problem on my 04 expedition. I just bought it and the headlights were aiming too far down. A rather larger gap was noticeable between the headlight and the hood. The so called adjustment bolt did nothing. I removed the headlights and found 2 issues. On the adjustment bolt there is a washer. Make sure when you re-install the headlight the washer sets on top of the plastic slot and is visible when looking down behind the headlight. Without the washer being in the correct location it will not tighten the headlight in place.
Second I found the adjustment bolt adjusted nothing. It merely tightened the headlight in place. What I had to do was to loosen this bolt and physically move the headlight into place and the re-tighten the bolt. Hence the slot is the adjustment. Turning the bolt CW or CCW did not move the headlight.
I tried several things trying to figure why the lights would not move until I realized I could move the light with my hands and tightened them in place using the adjustment bolt.

This may not be your issue but I found the owners manual instructions to be useless.

Dec 28, 2008 | 2004 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...