Question about Cars & Trucks

Open Question

The cams have numbers on them 2-5, what witch intake cam goes on the right side?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: cam shaft timing

Nned to know if you have a V6 or a 4 cyl.

Posted on Sep 29, 2008

Ad
alicantecoli
  • 22219 Answers

SOURCE: replacing timing chain

didnt you make it before you took it off ??,piston no1 at tdc and valves on no1 closed and no 4 open ,TURN ENGINE 360DEGREES WITH A RATCHET BEFORE TRYING TO START ENGINE

Posted on Dec 16, 2008

old marine
  • 1992 Answers

SOURCE: how do you set the cam timing on a dodge 2.7

Here are the diagrams for the secondary timing chains (exhaust cam - intake cam) and the primary timing chain. (courtesy of AutoZone)

10bc7b2.gif

60dbeef.gif

Posted on Feb 25, 2010

jturcotte
  • 8522 Answers

SOURCE: 2001 2.4l turbo timing marks see marks on cam

everything is at 12 o'clock. see diagram from autozone.com

1515ac4.gif

Posted on Sep 29, 2010

  • 9 Answers

SOURCE: I have a 2007 suzuki xl7 w/ check engine light on.

I have the same problem few days ago and found my solution on Fixya Expert Sources website. Here you will get all the top sources of your problem. All the sources of this site provided by top Fixya Gurus. Have a good look at the sources of the page. Go through the sources to find your solution. Hope it will help.


View Count:9

Posted on Aug 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know how to set the timing for an 05 kia rio and there are no repair manuals for this car please help


YOU HAVE 2 CAM GEARS . A INTAKE CAM AND AN EXHAUST CAM . ON THE INTAKE CAM THERE IS AN I FOR INTAKE WITH A MARK STRAIGHT ABOVE IT AND ON THE EXHAUST CAM THERE IS A E AND RIGHT ABOVE THAT IS A MARK. LINE THE I MARK UP WITH THE MARK ON THE BACK OF THE INNER COVER [WHICH IS A LITTLE MARK KINDA LOOKS LIKE AN ARROW] THIS IS ON BOTH SIDES . ON THE CRANK THERE IS A KNOTCH ON THE BACK OF THE TIMING GEAR FOR THE CRANK AND A MARK ON THE THE COVER LINE THE 2 UP AND YOUR THERE. IF YOU HAVE ANY MORE QUESTIONS YOU CAN E MAIL ME GOOD LUCK

Jan 31, 2011 | 2005 Kia Rio

1 Answer

Timing marks for the Dodge 2.4L caravan, 2000


To align both sets of timing marks, turn engine crankshaft to the right with belt on cam and crank. Once you have done this the crankshaft alignment mark (on front of crankshaft gear) will line up with mark to the rear of gear on engine block.The two cam gear timing marks should be alines across from one another. The right cam gear is the intake side and the left side is the exhaust side. After removing the belt turn the exhaust cam down 1/2 notch. Timing mark on exhaust 1/2 notch down from the intake side. Install new belt and recheck everything to make sure it's all correct. Hope this will help you.

May 16, 2010 | 2000 Dodge Caravan

1 Answer

2002 escape 3.0 camshaft cap bolt torque specifications


make sure to apply 5w-20 oil to caps prior to install. Also caps and journals are number so you do not install in wrong place. Starting with Righ side looking at pulleys from front, right side cam start with first cap on left being #1 then bolt on other side of cap as #2. Cap behind would be #3 to left then #4 bolt next to it. Keep tightening the next 2 caps behind them in same manner, then jump to front of cam to left side and tighten caps front to back. You should tighten to 10 Nm (89 lbs-in) with a torque wrench. Then you tighten left side head cam caps starting with the left side if looking at front pulleys. Start at front caps working to rear then jump to right side cam front to back. Tighten these caps at 8 nm (71 lb-in) using torque wrench. Also make sure if heads are bolted to block that cam pulley postion is the following: left side looking at pulleys------left pulley mark at 12 o'clock right pulley mark at 3 o'clock. Right side head looking at pulleys------- left side pulley at 9 o'clock and right side pulley at 12 o'clock. When I say clock postion that means using head where valve covers meet as your straight vertical postion.

May 05, 2010 | 2002 Ford Escape

1 Answer

Where are the cam sensors (2) located on my 2005 chevy colorado


I have a 2005 and the things that go bad on it is when the sensor goes off then for the intake then where the butterfly is on the intake gets dirty and needs to be cleaned it is the venturi gets dirty and needs to be cleaned and if it is a cam crank then it is the cam actuator that needs fixed you can tell if you take it off and there a screen missing it is a good sign that it needs be replaced and it is on the left side of the engine you need to understand that if it gives you a code that tells you that it is a sensor that is telling you that what the sensor looks after is bad not the sensor

Apr 11, 2010 | 2005 Chevrolet Colorado

1 Answer

Timing belt replacement


yeah you can do it without the special tools, i work at a dealer and i dont even use the special tools,,,once you get the timing belt cover off,rotate the engine till all the timming marks line up,there are notches on the timing belt backing plate and they match the marks on the cam sprockets,now thew cam all the way to the left is 1 then 2 and 3 and 4 being all the way to the right becarefull the cams have more than one number on them so make sure the #1 on the #1 cam is up and #2 on 2 cam and so forth,otherwise you will bend the valves and ruin your engine,,,the crank sprocket has a mark on it as well as does the oil pump to line it up youll see it thru the passenger side tire well,,,then remove the 13mm nut from the tensioner,its the one all the way to the left under the cam sprocket #1,,and then remove the belt,,,now when u put the new belt on start atthe number 2 cam sprocket and put it on ,,there are no marks on belt to line up so its very important you have all marks on cams and crank lined up,,,then after its on #2 go around the upper tensioner pulley between #2 and #3 cam and make it tight and wrap it on #3 and the #4 sometimes u gotta move the cam a hair to get the teeth to line up on the belt so it goes on but it will all line up perfect in the end,then go around #1 make sure all cam are lined up and belt is tight,,you can not have it off even a tooth,,,then go around #4 to idler and around crank on right side and on left side go around crank too,now i usually use small vise grips with very light pressure to keep the belt on the cams,so they dont jump,,,then pull down on the right and turn crank front 2 teeth and put belt on crank and then put crank back to normal spot and then all you excess slack should be right where the tensioner is at the left that you took off before,keep all the slack there,,,,and the put the tensioner on while holding the belt tight and then use a allen wrench and 13mm wrench to adjust and tighten belt tensioner,,,,make sure all your marks line up,,, osometimes if you havent done this before it may be easier to have another set of hands to help you hold thingss

Sep 24, 2009 | 2003 Saturn VUE

1 Answer

How to find where the cam shaft sensor is located


The cam shaft position sensor is located right behind the exhost cam by the fire wall. It is held by two 10 mm bolts, one on each side of the sensor. If you got the hood up and looking at the engine the cam that is on the right hand is the exhost cam. To get to the CPS you have to remove the intake and cam top cover.

Jun 13, 2009 | 1999 Kia Sportage

1 Answer

Timing marks


this is an easy one to time. the timing mark for the crank is 0 degrees-do not attempt to tum crank if cam timing is out. there is no distributor on this engine-it is advanced with your intake camshaft. The intake camshaft is the only tricky part to time. Be very careful because at 2500 rpm this cam actually moves forward via cam advance solenoid. It will hit your crank if not timed properly! so with your crank at o degrees-camshafts out of head if you need to turn engine to line up crank-on the exhaust cam(your left)behind the gear(on flange) there will be a hole big enough to put a small punch in that will line up with the top of the deck surface on the outer side(to the left). Now on your intake cam(your right) it will be just the opposite. the hole on the back side of the gear flange will line up on the right with the to p the deck surface. once in line hold intake cam and turn the gear(advancer) all the way to the right)-very important. You will have to start with you intake(put chain on) then line up your exhaust and install timing chain tensioner. always turn engine 360 degrees and recheck before you proceed. At least your at top dead center and you can visually see the lobes on both cams mostly straight up. hope I have been helpful.

Jun 07, 2009 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

1 Answer

CAM SHAFT MARKS 2002 SATURN VUE 3.0L


This is a pretty tough timing belt job to do if you have never done one before. There is also a kit of tools that are essential to getting the timing right on this engine. The cams are numbered 1-2-3-4 from left to right if you are facing the cam sprockets. If the tensioner was broken and the engine came out of time you are probably looking at at least a few bent valves. Could be time well spent to perform a leakdown test before you spend too much time on installing a timing belt.

Dec 05, 2008 | 2003 Saturn VUE

1 Answer

Timing


Yes - on the V6, the left intake cam and exhaust cam are on the same side of the vehicle. Facing the engine, the "upper" cam sprocket on that side is the intake cam, and the one that is lower and farther out toward the fender of the vehicle is the exhaust cam.

Aug 25, 2008 | 2002 Isuzu Rodeo

3 Answers

How to replace timing belt on 1997 kia sportage


you have 2 sprokets to worry about the top two and crank gear, the crank gear has knocht on it and index on block ( towards back of gear visible from top) place on tdc mark ( top dead center), install the timing belt on this gear first then secure it with a piece of hose or anything that fits in between housing and belt to secure belt from moving from gear) then align the right side sproket on "E" for exhaust cam at top marks on cover and sprocket, then install belt over that sprocket, finally align left side sprocket "I" for intake to the top mark and install belt not too tight or it will make noise just make sure it is firm. now to double check from left to right with you standing in front of vehicle you should have left cam sprocket with "I" for intake to the top and right sproket with "E" for exhaust to the top. having bottom gear on tdc (top dead center mark) and all marks lined up with belt installed and proper tension secured, turn engine over twice and make sure marks meet in the same place then put everything back together. ( recommend you replace both idler and tension pulleys and check water pump, replace if needed or you'll be back.- this procedure goes the same to spectra, sephia, sportage, you will not damage the engine on these vehicles if belt goes out except rio. if timing belt goes out on the rio it will need an engine, if lucky just head. recommended replacement on all is every 60k miles) goo luck tightening the power steering drive belt when you put everything back together, just use a long bar to pry and good leverage. and a second hand comes in handy.

Aug 02, 2008 | 2002 Kia Sportage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...