Question about Cars & Trucks

1 Answer

No Rear brake lights, deck stoplight, turn and tailights work, hazard switch froze, removed shaft of hazard switch, found to be melted, how to pull switch, pull steering wheel? 2002 Grand Prix GT

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 8,531 Answers
Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2002 jeep grand cherokee. Rear left brake light isnt working

The problem with your tail light is the housing is broken where the socket goes in. If you pull that socket out and look you will see the metal tap will be pushed down and the plastic around that will be broke. Easy fix is to replace the lens but you can get under the metal tap with a small flat tip screw driver and pull up on it very lightly and it should work for awhile.

Hope this helps
Cory

Posted on Dec 23, 2008

  • 4 Answers

SOURCE: 2001 Grand Prix GT

I have the same problem and it is the switch... I ran a wire from my back window light to my brake lights and it works great. saved 600.00 bucks and only took 20 min Danny

Posted on Feb 24, 2009

  • 335 Answers

SOURCE: All lights work on the rear except the three brake lights

Sounds like the brake light switch has a problem. Located above brake pedal and activated with the brake pedal arm. Check for power going in and coming out when you apply the brake.

Posted on May 24, 2009

  • 6 Answers

SOURCE: 1998 Lincoln TC no brake or hazard lights work.

Hazard light switch... They all intermingle in operation.
My ex wifes 96TC was doing the same thing... I could OCCASIONALLY get the hazards to work by turning the hazard switch on/off like 10 times in a row and suddenly it would fix... finally bought a new switch

Posted on Sep 14, 2009

Testimonial: "Will try your advice, not sure were the hazard switch is (owners manual missing) so I'll call around. thanks, awa prompt."

  • 7353 Answers

SOURCE: 95' Buick regal, 3rd brake light works, tail

I dont have a diagram but the brake light switch has to feed the turn signal switch, Either that wire has a bad connection, or the turn signal switch is bad. Jiggle the turn signal lever and see if the brake lights try to work.

Posted on Nov 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why aren't hazard lights or brake lights working?


Brake lights /rear hazard lights not working - Ford Truck ...

www.ford-trucks.com > ... > 1967 - 1972 F-100 & Larger F-Series Trucks
Jul 9, 2010 - After checking the brake lights I tried the emergency flashers and found that they are working in the front but not in the back. I do have rear turn ... 1995 F350 Brake Lights / Turn Signals not working
Jul 9, 2012
Turn Signals and Brake Lights Do Not Work
Mar 10, 2012
Turn Signal, Brake Lights, & Rear Hazard not working
Aug 3, 2010
Rear Turn Signals, Hazards and Brake Lights not working....
Aug 29, 200

Sep 30, 2015 | Cars & Trucks

1 Answer

I just bought the car the turn signals work in the front but not in the back whats the problem?


Have you checked the bulbs already?
Don't know what kind of car you are dealing with here.
Most vehicles - the brake lights and rear turn signals share the same electrical circuit to the rear tailights. Usually the turn signal switch will separate which signal goes to the back.
Do your brake lights work? Is there a High mounted stop lamp and does it work?
I have seen a Hazard Switch be ON and fuse blown causing the Hazard Flasher to be inop - which prevented the turn signals from working. Turning OFF the hazard flasher brought back the T/S.
Check the rest of the lights - see what does and doesn't work - and do the front turn signals flash? Stay On? Or flash really slow?
Let me know what you find out and if this helps you at all.

Mar 12, 2015 | Cars & Trucks

1 Answer

I have a 2006 Chevy Silverado 1500 Extended Cab 4x4. My question is that when the truck is parked & not running with no keys in the ignition , my brake lights will begin to flash on & off until it drains...


Stop lamp circuit discription

Stop Lamps
The STOP LP 25-amp fuse in the underhood fuse block supplies battery positive voltage to the normally open stop lamp switch. When the driver presses the brake pedal, the switch contacts close and battery positive voltage is supplied to both the STOP 15-amp fuse and the center high mounted stop lamp (CHMSL) 10-amp fuse in the instrument panel (I/P) fuse block, and to the turn signal/hazard module. The turn signal/hazard module then supplies voltage to both of the trailer rear turn/stop lamp supply voltage circuits. The voltage from the CHMSL 10-amp fuse is to the CHMSL and the trailer jumper harness. The voltage from the STOP 15-amp fuse is to the stop lamps, throttle actuator control (TAC) module, and the cruise control.

I think The turn signal/hazard module has something to do with the lights flashing .From looking at a wiring diagram B+ voltage from the STOP LP fuse 25amp in the under hood fuse box supply's the brake light switch , from there it feeds B+ to VEH STOP fuse 15amp and VEH CHMSL fuse 10amp an to stop lamp switch signal to the turn signal flasher module which is suppose to control the trailer stop lights . Do you have a connection for a trailer hook up ?
Remove both LT an RT TRLR fuse's both 10 amp from the I/P fuse block an see if the problem goes away .

Do you tow a trailer ? Check the trailer connector for corrosion !

May 15, 2017 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

1998 cadillac eldorado rear brake lights and hazzard lights do not work


More likely that the turn signal switch assembly is bad.Have someone watch the tailights(or use a large mirror) to see if the bright tailight filaments come on with the brake pedal held down while you wiggle the hazard light switch.

Mar 08, 2013 | 1998 Cadillac Eldorado

1 Answer

Where is the brake relay on a 2001 gmc sierra.


Try wiggling the hazard light switch while pressing on the brakes.The taillights are connected to the turn signal switch before it goes to the brake switch.The contacts on the hazard switch are probably dirty(I remember this problem years ago,same symptoms-3rd light works but l/R tailights not working).You may just be able to turn the hazards on+off a bunch of times to clean the contacts instead of replacing the switch.

Jun 13, 2012 | 2001 GMC Sierra 1500HD

1 Answer

I have a 1977 Mercury Grand Marquis the turn signals, brake lights, and turning lights do not work. The running lights and hazard lights do work. I checked the bulbs and the relay can for the turn signals...


Turn signal switch (also brake light canceling switch) most likely bad or bad wire to it or from it. Check, with key on run, for power into switch. Turn switch on, check for power out. No power out switch bad. Power out, trace to rear tailight harness for broken wire.

Jun 30, 2010 | 1977 Mercury Grand Marquis

1 Answer

No brake light or hazard warning flashers in rear


It appears to be the mutifunction switch. (Turn signal control). That, plus the 3 words in parenthesis wil come to 699.00 bucks. then we add the switch.... Just kidding. The multi finction switch is defective and about to fail altogether.. Sorry.

Oct 07, 2009 | 1998 Lincoln Town Car

1 Answer

Brake & Turn signals do not work when headlights are on


The problem is what they call the printed circuit in the tail light. Remove the twist off light bulb connector. You will see the contacts inside and that the plastic is warped. You can purchase the entire fixture for about $350 if you replace it yourself. A dealer will charge about $450 per tail light fixture. Chrysler won't admit they have a problem that they should have issued a recall for. The problem is that if your stoplights are out, you may be involved in a rear end collision. Chrysler doesn't care. What I did was purchase a right angle tailight bulb holder and standard #1197 stoplight bulbs from advance auto supply. You have to trim the existing socket a little and splice the wires for the new light socket, but it beats paying $900 for replacing the two fixtures. I fixed mine about a year ago and haven't had any problems.

Jul 23, 2009 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...