Question about Cars & Trucks

Open Question

I'm trying to understand my service manual. 2012 Stratoliner has displayed F 1.4, assuming F means Fault. 1 or 01is the fault & sub catagory 4 being the cause needing / inspection / repair. Paul

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 979 Answers

SOURCE: service engine soon light is

How's that gas cap doing? It's part of the canister circuit and Will cause this code if the seal is leaking...accordianman

Posted on Jul 28, 2008

alicantecoli
  • 22133 Answers

SOURCE: reset fault code on 1996 jaguar x300

dealer only sorry

Posted on Dec 10, 2008

emissionwiz
  • 75807 Answers

SOURCE: 1996 monte carlo fault codes po300, 441, 705,

THESE ARE FROM THE GM CODE DIFINITION MANUAL, U NEED TO TAKE THIS TO THE DELAER, U HAVE SOME SERIOUS PROBLEMS TO GIVE THIS MANY CODES.

P0300 - Engine Random Misfire Detected
P0441 - Evaporative Emission Control System Incorrect Purge Flow
P0705 - Trans Range Switch Circuit
P1106 - Manifold Absolute Pressure (MAP) Sensor Circuit Intermittent High Voltage
P1133 - Heated Oxygen Sensor (HO2S) Insufficient Switching Bank 1 Sensor 1
P1441 - Evaporative Emission (EVAP) System Flow During Non-Purge
P1662 - Cruise Lamp Control Circuit
P1672 - Low Engine Oil Level Lamp Control Circuit
P1870 - Transmission Component Slipping

Posted on Mar 24, 2009

  • 101 Answers

SOURCE: 2005 ToyotaCamry fault code P0500 Vehicle Speed sensor Malfuction

They are not the sensors you want. The car uses the abs wheel sensors for vehicle speed. Your problem lies in the abs system , possibly the left front sensor, abs ecu or speedo cluster, Clear the code and see if it stay out otherwise you'll need to go to a trusted technician. .

Posted on Apr 19, 2009

Mustgo
  • 2359 Answers

SOURCE: "SRS-AIRBAG SERVICE" fault message

Here's a quick check list for most common cost of SRS / Air bag problem.

Dirty contacts on driver and passenger seat belt buckles

Dirty contacts on seat belt connectors (under seats)

Dirty contacts on driver and passenger sides weight sensors (under seat)

Seat covers

Weight on passenger seat
(Example: grocery package trigger SRS / Air Bag light on the way home.)

I recommend you to pass an vacuum over the contacts and use CRC electronic parts cleaner to rule out connectivity problem.

I DO NOT recommend disconnecting the negative battery connector to clean the code(s).

Without the code(s) the dealer will takes "BILLABLE" time to reproduce the problem.

======

Please rate my answer if it is useful to you.

Cheers,

Mustgo

Posted on Dec 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0171 trouble code on 2012 Kia Soul


Follow the link on the fault code and its possible reasons for setting.

P0171 Kia Bank 1 System Too Lean

Jul 07, 2017 | Kia Cars & Trucks

1 Answer

2012 hino fault code p204f. Wat does it mean


the fault code will be specific to hino so take it to a service dealer for a code cause

Dec 30, 2016 | Cars & Trucks

1 Answer

2012 freightliner cascadia DD15 fault code ECU 1... prior to the fault code the engine bogged down really bad and solid yellow and check engine light come on.


an answer from just answers reports this
ecu 1 fault means the engine ECM has an internal fault and needs to be replaced
most of the time with this code it is not the ECM itself but usually a wiring problem going to the ECm
there should be 2 fuses for the ECM either next to the ecm in plastic covers by a starter or in a plastic box
check all wiring going to and from the engine and battery grounds
especially the grounds
check for wires rubbed through and loose terminals
take it to a service dealer for a proper diagnosis as it costs money wasting time trying to find the fault yourself as a truck standing still is not earning it's keep

Jun 05, 2016 | Cars & Trucks

2 Answers

Skid traction control light,abs light ,service 4 wheel drive light come on dash


first have diagnostic test done to retrieve fault codes and to see what sensors come up as components related to fault

Mar 15, 2016 | 2012 Jeep Liberty Sport 4dr SUV 3.7L V6...

1 Answer

I've tried resetting the engine light on a 2012 Mercedes E350 but the engine light is still lit. Now it displays "reset cannot be done" What am I doing wrong?


If it is emissions related the cars computer will not reset if the fault is not repaired, and fault/repair path in the diagnostic computer is not followed thru.

Sep 21, 2014 | 2012 Mercedes-Benz E-Class

1 Answer

What does brake lamp bulb fault mean?


It means that one of the stop lights is not working. Check out the brake lights and replace the blown bulb. It may also mean that the brake fluid in the master cylinder reservoir is low and needs topping up.

Jul 31, 2014 | 2012 Ford Focus SE 4dr Hatchback 2.0L...

1 Answer

Have a 1997 honda accord ex with a trouble code P1253, any ideas what that could mean?


hello ragdollsophi,

I am assuming you have a 4 cylinder engine. P1253 usually indicates a problem with the VTEC solenoid, connector, or wiring. I would recommend clearing the fault. After getting the fault cleared, in a safe area, accelerate the car in low gear to at least 4000rpm for 2-3 seconds. If the fault does not come back, then repeat the drive test a few more times. Assuming the fault does not return, the problem is intermittent.

Jun 25, 2011 | Honda Accord Cars & Trucks

2 Answers

Need to find obd in 1990 honda accord


TROUBLE CODES System Diagnosis READING CODES When the "Check Engine'' warning light on the dashboard comes on and stays on, it indicates a problem in the fuel injection/emissions system. Check the ECU for fault codes. On certain models, some codes will not trigger the check engine light; if driveability has suffered, check for stored fault codes. The most common error when using fault codes is to assume the indicated component has failed rather than checking the entire circuit. The presence of a trouble code means simply that the electrical circuit for the named component is not functioning properly. For example, a code for the oxygen sensor circuit does not automatically mean the oxygen sensor has failed. A wire terminal may simply be loose or corroded at the connector. When using diagnostic or fault codes, always remember that the entire circuit including the component must be checked carefully. On 1990-95 Accord (except V-6) and 1992-95 Prelude, the codes are read from the check engine light after the two-wire service connector has been jumpered. On Accords, the service connector is under the dash on the passenger side. On Preludes, it is located behind the center console. Codes 1 through 9 are indicated by a series of short flashes; two-digit codes use a long flash for the first digit followed by the appropriate number of short flashes. For example, Code 14 would be indicated by 1 long flash followed by 4 short flashes. Codes are separated by a pause between displays. Multiple codes are transmitted in an alternating pattern. For example, a code 3 and 14 would be displayed as 3 short flashes (for Code 3) followed by the separator pause, then 1 long flash and 4 short flashes (for Code 14). Fig. 7: Fault codes are read from the check engine light on most late-model vehicles 86804048.gif
Fig. 8: On Accords, the service connector is located under the dash on the passenger side 86804049.gif
Fig. 9: The service connector on Preludes is located behind the center console 86804050.gif
  1. Use a jumper wire to connect the two terminals of the service connector together.
  2. Turn the ignition switch ON; the check engine light will display any stored codes by rhythmic flashing. NOTE: In the event that a code is encountered which is not on the chart, re-count the number of flashes. If the code is truly wrong, it will be necessary to swap the ECU for a known-good unit and recheck. Since this can be expensive, you may wish to bring the car to a reputable repair facility if no other cause of the failure can be found. This may save you the expense of purchasing an unnecessary part.
  3. If no codes are displayed but a driveablity problem exits, testing of the system individual components is necessary to find the problem. If codes are displayed, follow the appropriate troubleshooting chart in this section. Fig. 10: Fault code chart for 1990-93 Accords 86804051.gif
    Fig. 11: Fault code chart for 1994-95 Accords (four cylinder) 86804052.gif
    Fig. 12: Fault code chart for 1992-95 Preludes 86804053.gif

Dec 14, 2010 | 1990 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...