Question about Buick Cars & Trucks

1 Answer

What is the torque specks for a 3.8 lt v 6 rear main cap 1987 buick regal turbo

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 3,495 Answers

Main bearing cap, vin 7--100ftlbs, all of them.

Posted on Aug 10, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
salvidordali
  • 103 Answers

SOURCE: replace rear struts 1996 buick regal

Here is a link describing your strut replacement. Autozone also has free tool rental for the strut spring compressor if you need it. Thank you, and don't forget to vote. http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800681ba

Posted on Jan 29, 2009

  • 840 Answers

SOURCE: Engine torque settings VW lt 35 1993 2.4 turbo diesel. Code ACL

bob go to collsionrepairadvice.com and I will send the download to you its a big file

Posted on Mar 13, 2009

  • 82 Answers

SOURCE: 87 regal ignition switch wiring diagram

Thick wires at IGN SW .... Red(s) - supply power from the battery to the IGN switch ... Pink - ignition supply ... Orange - Accessory power ... Purple most RWD sometimes (Yellow most FWD) - Starter .. Did I miss any? It's been a while The thin wires on the IGN swich are for key sense and VATS (if applicable)

Posted on May 08, 2009

  • 2 Answers

SOURCE: VACUUM HOSE DIAGRAM FOR 1987 BUICK REGAL GRAND NATIONAL

sign up at turbobuick.com (it's free) then find out who lives near you and check out their car...take some pictures and notes...btw there are a ton of members and I'm willing to bet someone lives near you and most are more than willing to help out a fellow turbo buick owner..or try the link at the bottom...any problems shoot me an email at Mansfieldroof@aol.com

http://www.installationinstructions.com/vin9/vacuum%20hose%20system.pdf

Posted on Jun 16, 2009

  • 44 Answers

SOURCE: how to change the rear 3 spark plugs on a Buick regal LS 2002

You can try rotating the spark plug boot a little bit-not even a 1/4 turn-to break the seal between the plugand the boot. Then pull the boot wire off with a pliers on the metal boot shield. Once the boot has beet rotated on the plug, the shield helps to remove it.

Posted on Oct 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the Wire Order with distributor?


theres no distributor and the firing order for your 3.8 is 1-6-5-4-3-2-the following link shows the coil pack
Buick General Motor 3800 V6 Engine Firing Order DIS IDI ignition timing 3.8 Buick Engine Coil Pack Firing Order Spark Plug Wire Location Which way do the spark plug wires go on & what cylinder is what?
.
For the Buick V6 231 3.8 liter turbocharged engine:
.
Answers!
.
Firing order:
1 - 6 - 5 - 4 - 3 - 2.
.
Spark plug wire location on coil pack:
.
Closest to the back of the car, left to right: 1 - 5 - 3.
Closest to the front of the car, left to right: 4 - 2 - 6.
.
Spark plug wire location on engine:
.
drivers side, front to back of car: 1 - 3 - 5.
passenger side, front to back of car: 2 - 4 - 6.
.----and this link shows the coil pack to cylinders
.
3 8 Buick Turbo Engine Coil Pack Firing Order Spark Plug Wire Location

Aug 15, 2015 | 1987 Buick Regal

1 Answer

Dont have spark 1987 buick regal 3.8l turbo


Have you checked the coil pack and the module to see if they are getting voltage and a ground signal ?

Jan 14, 2013 | 1987 Buick Regal

1 Answer

I need accurate torque specifications for rod and main bearing caps for a 2.0 liter 96 Eclipse turbo


I need accurate torque specifications for rod and I need accurate torque specifications for rod and main bearing caps for a 2.0 liter eclipse turbo 90 help plis

Mar 23, 2011 | 1996 Mitsubishi Eclipse

1 Answer

Need to know crankshaft main bearings and rod bearings torque specks.


2 Different size engines for that year. If you have the 2.2 the main bearing caps are 70 ft/lbs (final torque) & the rod bearing caps are 38 ft/lbs (final torque). If you have the 4.3, the main bearing caps are 77 ft/lbs (final torque) & the rod bearing caps are 45 ft/lbs (final torque). I hope this helps and good luck.

Mar 13, 2011 | 1996 Chevrolet S-10 Pickup

1 Answer

What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...


Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

May 17, 2010 | 1997 Ford F150 Regular Cab

1 Answer

Firing order diagram for a buick


For the 3.8L:
Firing Order:
1-6-5-4-3-2

Cylinders:
(back of engine)
2--------4---------6
1--------3---------5
Ignition Connections:
(back)
___
o-<-----6
___
o-<-----3
o-<-----2
___
o-<-----5
o-<-----4
___
o-<------1

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Mar 04, 2010 | 1994 Buick Regal Gran Sport

2 Answers

Can't find the fuel filter on my 1987 buick regal grand national


its toward the back on the driver side by the rear end on the under carriage

Aug 16, 2009 | 1987 Buick Regal

1 Answer

VACUUM HOSE DIAGRAM FOR 1987 BUICK REGAL GRAND NATIONAL


sign up at turbobuick.com (it's free) then find out who lives near you and check out their car...take some pictures and notes...btw there are a ton of members and I'm willing to bet someone lives near you and most are more than willing to help out a fellow turbo buick owner..or try the link at the bottom...any problems shoot me an email at Mansfieldroof@aol.com

http://www.installationinstructions.com/vin9/vacuum%20hose%20system.pdf

Apr 07, 2009 | 1987 Buick Regal

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...