Question about Cars & Trucks

1 Answer

I'm trying to fix a broken tone ring can I press the front half shaft myself the ring or do I have to take it to the shop to be pressed

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 1,648 Answers

Got a press?

Posted on Aug 10, 2017

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
autotherapis
  • 501 Answers

SOURCE: I'm preparing to remove front right axle shaft (Cv half shaft)

It is held in by a spring ring. You need a good strong pry bar and you position it between the hub of the axel and the case of the trans and **** hard pulling it out. It sometimes is seated well, but keep trying. It will fight you sometimes.

Hope this helps.

Posted on Sep 15, 2009

Testimonial: "Thanks a bunch. I wanted to make sure I wasn't mistakenly trying to pry a snap ring off. Took long enough to get the axle nut off easy from here."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to diagnose if tone rings are bad. can they be replaced or must you replace half shaft


Turn the axle and look at every tooth if you see it cracked any where in between then shaft will be needed as these are pressed on.

May 03, 2014 | 2006 Chrysler 300

1 Answer

Wheel sensor


Tone rings are a break for the magnetic field produced by the sensor if you have to much air gap you would get a erratic signal if the tone wheel is broken any where this will produce a fault or failure, if the sensor fails same result.a scanner can read this signal if the sensor can produce it other wise you may have a open circuit usual failure is the sensor.

May 02, 2014 | 2006 Chrysler 300

1 Answer

Front passenger side broken axle


Need to replace the drive shaft. Aftermarket parts work fine. The biggest issue is removing inside connection to the half shaft. The clip ring tension is stronger than the boot holding the inboard joint on the drive shaft. To break it loose get a large screw driver and from under the car in front hit the inboard joint hard several times until it over comes the clip ring. Remember... always use jack stands when working under the car.

Aug 12, 2013 | 2005 Acura TL

1 Answer

2008 ford escape abs and traction control light is on, if the car sets over night the traction control light and abs lite doesn't come on until a few minutes and after the car sits around awhile the...


2008 Escape has a terrible reputation for ABS light and traction control light being. All due to broken ABS tone ring cracked and out of position flopping on frt bearing. Go to local AutoZone store and they will scan this to find which wheel has the broken tone ring. The replacement ring is cheap in the $7 range. It is labor that will sicken you as this ring must be pressed on after the front half shaft is removed. Not a driveway job if you are considering DYI.

Jun 21, 2011 | Ford Escape Cars & Trucks

1 Answer

Abs light, brake light, and traction control light always on, and blower does not work. lights rarely shut off, and when they do, the blower kicks on. sometimes it is for a split second or for a while. and...


Hi, you have gremlins. First of all, check your brake fluid level. This may or may not be related to the ABS and TC lights. Those are casued by wheel speed sensor issues. Check all the sensors and tone rings. Look for hydraulic leaks also while you're checking the sensors. Fix any broken wires. Make sure sensors are centered on tone rings. Especially a problem with the front, where the tone ring is on the half-shafts that were removed for the tranny work. Make sure the axles HAVE tone rings on them!!!
Fix any brake leaks and bleed the brakes. Let me know if you need any instructions on that work.

Check to make sure the ground strap from the battery to the engine and from the engine to the chassis is on and tight.
Which lights are staying on?
For the radio, check the speakers using another radio or use the one speaker that works to check the wires for the rest of them.
I'm willing to help, but someone's going to have to get their hands dirty to fix all these problems...and it can't be me 'cause I'm only virtual.
Are you up for it?

Jan 08, 2011 | 2001 Pontiac Sunfire

2 Answers

How do I replace the front wheel bearing on a Passat 97-00. I have removed, wheel and brake assembly.


First you need to untight the half shaft nut, than detach all ball joints (4 of them), than you remove the hub from the half shaft, you will actually need to have a press (about 12ton min) to press the bearing out and press new one in, don't try to hammer it as you can possibly damage the hub and than you will need to buy new one (or second hand). After getting it pressed in you basically need to put it back and reverse the whole process of dismantling.

Apr 26, 2010 | 1998 Volkswagen Passat

1 Answer

Were is the abs sensor mounted on the rear of an


The ABS sensor are attached to the brake backing plate assemblies and tone rings are pressed on the axle shaft. Use care when removing axle shaft as NOT to damage the tone wheel or the sensor.

In the ZJ-Secc-5-Brakes (page 25) can find information about the sysrtem and sensors location.

I really hope helped with this; remember rated this help. Good luck.

Nov 30, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Where is the speed sensor on a 2001 kia sportage located?


The speed sensors are a single pole, variable reluctance sensor, mounted to the rear axle housing and both front half shafts.

A toothed tone ring is press fit to the differential carrier next to the drive gear and provides the signal for the rear sensor.

The front tone rings are press fit to the half shaft assemblies

Nov 15, 2009 | 2001 Kia Sportage

1 Answer

4x4 Problems


sorry lost here ,never seen one but if transmission shaft is turning to front diff then the problem is their,could be anyting from a sheared diff pinion to a broken planet wheel or possible evan a snapped half shaft or the spline on the end of the half shaft has worn and rounded off

Oct 07, 2008 | 1999 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...