Question about Cars & Trucks

Open Question

I lost mu cord and with wall plug to charge my Sony Cyber-shot 16.1 mgp camera Need a new one

Need replacement Part #1-846-062-21 and Part #1-492-868-11.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need to make reservation from 19/12/2017 to Cape Town from Polokwane or Pretoria . Prces and time schedules pleas4?


In some cases, a printer reset can clear the error message.
  1. Turn the printer on, if it is not already on.
  2. Wait until the printer is idle and silent before you continue.
  3. With the printer turned on, disconnect the power cord from the rear of the printer.
  4. Unplug the power cord from the wall outlet.
  5. Wait at least 60 seconds.
  6. Plug the power cord back into the wall outlet.
    note: HP recommends connecting the printer power cord directly to the wall outlet.
  7. Reconnect the power cord to the rear of the printer.
  8. Turn on the printer, if it does not automatically turn on. The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.
  9. Wait until the warm-up period finishes and your printer is idle and silent before you proceed.
If the issue persists, continue to the next step. Step 3: Check estimated ink levels The error might be caused by a low or empty ink cartridge. If an Ink Alert message displayed before the error occurred, replacing the ink cartridge(s) might resolve the issue.
Check your printer control panel for the Estimated Ink Levels feature. Control panel options vary by printer model. If you are unable to display the ink levels on the printer control panel, select your computer operating system below.
note: Ink level warnings and indicators provide estimates for planning purposes only. When an indicator shows low-ink levels, consider having a replacement ink cartridge available to avoid possible printing delays. You do not need to replace ink cartridges until print quality becomes unacceptable.

Oct 16, 2017 | Cars & Trucks

1 Answer

1962 Ford Falcon wont run unless choke is partially closed


check the float level setting
it presents as a partially blocked main jet circuit
there could be corrosion in the circuit that the cleaning agent has not removed
it may be necessary to remove the lead blocks for the drillings to physically remove the blockage
if you look at the drillings and passage ways of the carby you will notice what appears to be plugs inserted where it has been necessary to use a drill to make a circuit for the fuel and air flow
these small plugs are lead pellets similar to shot in a shot gun cartridge that are inserted into the hole and pressed to expand and act as a plug
consider taking the carby to an accredited carby overhaul specialist shop where they can remove/ replace these plugs and test the carby on a machine for correct adjustment and settings

Aug 14, 2015 | Ford Cars & Trucks

1 Answer

Where do I plug in the cord to start charging the jump starter (Black & amp; Sage ) 900 peak ,350


Google for an owner's manual. I can't find anything on this jump starter, but first they need to be charged, usually by plugging into a wall socket for 12-24 hours. Then plug into the cigarette lighter for 10 min or so to give the car battery a boost charge.

Dec 04, 2014 | Cars & Trucks

2 Answers

My '88 F250 4x4 Diesel Won't turn over, Makes a "click" noise when key is turned. Amps are showing low (around 9-10) on the interior gauge... Batteries are at full charge. I've...


probably one or both or your batteries are low or shot, check both of them. Hope this helps-Jim If water in them is low, refill with distilled water, and then charge them. If it still doesn't start, you may need a replacement.

May 13, 2011 | 1988 Ford F 250

2 Answers

I just installed new alternator,starter & battery & the motor wont turn can u help whats causing that?


Replace the starter solenoide mounted on the fire wall or side of inner fender wall. Good Luck and have a good XMASS.

Dec 12, 2010 | 2004 Ford F150

1 Answer

Mu brake caliper barrel will not retract


The easiest way to do this is to keep the old pad on the caliper and use a C-Clamp with one end on the pad and one end on the caliper. The pressure from twisting the clamp should break it free and allow it to retract. If you've tried that and it remains "frozen" in place then you'll need a new caliper.

Sep 29, 2009 | 2007 Isuzu MU-7

1 Answer

Lost the driver side mirror, how do i replace?


inside the door it has a cap just remve it gentle with a knife or screwdriver.Insidide u will see 3 screwsremove it and unplug the electrical cord.At that moment the mirror is free pull it out and replace the new one plug the electrical cord,tight the screws replace the cap and check if its move with the control panel,Good Luck.

Mar 22, 2009 | 2003 Toyota Corolla

1 Answer

Rear window on 1999 Isuzu Rodeo won't stay up--seems like the shocks (manual calls them "gas stay") maybe shot--do you know how the replace them so the door stops klunking me on the head?


The window cdartrige has lost the charge. Unfortunately when this happens you need to purchase new ones. I hope this helps. Please rate my answer.

Jan 23, 2009 | 1999 Isuzu Rodeo

1 Answer

I need to find the engine heater plug in cord from my new-to-me 1997 F350 diesel


Look at the passenger side of the block. The rear freeze plug should have a block heater instead of a freeze plug. It'll be the rear freeze plug. If all you see is a 3 prong plug, the cord somehow got lost. I replaced on a truck very similar to yours. I got the entire assembly from NAPA. It comes with the piece that goes into the side of the block and has the cord with it so you can plug it into an AC outlet.

Nov 26, 2008 | Ford F-350 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...