Question about Cars & Trucks

Open Question

How far apart one these two building of horizontal plane

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust headlights horizontally on 2002 honda accord only see vertical adjustment


The manufacturer has not provided any adjustment for the plane of horizontal only up and down.

Nov 12, 2016 | Honda Cars & Trucks

Tip

How to adjust AUDI headlights beams


There are two adjustment points (screws). For example left headlight: you will see one point near the end of left wing, at bottom side through a wing hole. This is for vertical plane headlight beam adjustment (up-down). Another one point is against water radiator side. This is for horizontal plane headlight beam adjustment (left-right).

on Dec 18, 2009 | Audi A4 Cars & Trucks

1 Answer

I need to kniw start out driving instructions for my bayliner sierra 2855. I need to start with trim all the way up. And adjust down as I plain out or opposite way.


Start with the plane pads in just past level in the up direction. As you plain the boat bring them down slowly not to go to far.

Jun 19, 2015 | Cars & Trucks

1 Answer

Truck jumping in first and second gear once clutch is let out fully when accelarating


I am guessing here but I am sure that the yokes on the shafts are not in phase . That is to say that the cross pieces are out of wack. check the position of the gearbox yoke and place it directly vertical . Check the position of the joint at the other end of the shaft and the cross must be exactly the same . If it is off say 45 degrees then it has not been assembled properly. Now to explain it better . the ears of the gearbox yoke ( bit that has the 'U joint bearings in it) should be on top and underneath ---Vertical plane ---. That will place the ears of the shaft in the horizontal position now go to the rear end of that shaft and the ears of the shaft must be in the same plane . IF those eras are vertical ( the same as the gearbox yoke ) then it has to be pulled apart and rotated 90 degrees to be the same as the front of the shaft. Now the second shaft ( slip joint end and the diff end get the same treatment. So the slip joint yoke has to be in the same plane as the diff yoke. It all has to do with the shaft speeding up and slowing down as it rotates through the 90 degrees and the different "u" joint s speed up and slow down at different times so that one end cancels out the other and you have a vibration frees shaft. If you are still unsure go on the web and find a site the refers to drive shaft manufacture and problems and phasing

Mar 31, 2014 | 1994 Nissan King Cab

1 Answer

No instructions


Say, you need to re-post in another section for a response. This is cars and trucks...sorry.

Jul 12, 2012 | Cars & Trucks

1 Answer

I Have an Audi a4 Quatro 2004 model. Adjust Low Beams?


There are two adjustment points (screws). For example left headlight: you will see one point near the end of left wing, at bottom side through a wing hole. This is for vertical plane headlight beam adjustment (up-down). Another one point is against water radiator side. This is for horizontal plane headlight beam adjustment (left-right).

Nov 19, 2009 | 2004 Audi A4

1 Answer

AUDI A4 2003 1.9TDI HOW TO ADJUST THE HEADLIGHT


There are two adjustment points (screws). For example left headlight: you will see one point near the end of left wing, at bottom side through a wing hole. This is for vertical plane headlight beam adjustment (up-down). Another one point is against water radiator side. This is for horizontal plane headlight beam adjustment (left-right).
Please Rate my Response! Thanks!

Jul 13, 2009 | 2003 Audi A4 Cabriolet

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...