Question about Cars & Trucks

1 Answer

I need two alternator bolts - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 46,758 Answers

Wreckers/junk yards will have plenty of stocks

Posted on Aug 10, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to tide belt


okay loosen alternator pivot bolt that is the bottom bolt below the alternator pulley,loosen also top pivot bolt to alternator.then you have long adjuster bolt top upper side alternator you need to loosen adjuster bolt lock nut then tighten the adjuster bolt to get alternator belt tight.new belt tension should be 170 - 180 ft lbs, used drive belt tension is 95 - 135 ft lbs, torque adjusting lockbolt 13 ft lbs, pivot bolts to 41 ft lbs.

Sep 01, 2012 | 2002 Lexus RX 300

1 Answer

The battery and the alternator, need replacing on a 2006 6cyclinder, Taurus. I have the parts, and tools, I just never worked on a newer car before. I need a print out of instructions, please!!


Removal & Installation 3.0L (2V) To Remove:
  1. Disconnect the battery ground cable
  2. Remove the accessory drive belt
  3. Remove the fasteners and move the degas bottle aside.
  4. Disconnect the wiring from the alternator.
  5. Remove the brace and the alternator mounting bolt.
  6. Remove the alternator from the engine.
To Install:
  1. Install the alternator on the engine. Tighten the lower and right brace bolt to 18 lb-ft. (25 Nm) and the left brace bolt to 35 lb-ft. (48 Nm).
  2. Connect the wiring to the alternator.
  3. Install the degas bottle in the original position.
  4. Install the drive belt.
  5. Connect the negative battery cable.
3.0L (4V) To Remove:
  1. Disconnect the battery ground cable.
  2. Remove the accessory drive belt.
  3. Remove the power steering hose bracket nut from the alternator mounting bolt.
  4. Remove the upper alternator mounting bolts. NOTE: The left side bolt will come out with the alternator.
  5. Raise and safely support the vehicle.
  6. Remove the right front wheel.
  7. Remove the right inner fender splash shield.
  8. Remove the screws and the alternator splash shield
  9. Remove the torque converter inspection cover.
  10. Install the flywheel holding tool. holdingtool.gif
  11. Remove the bolt and the crankshaft pulley. NOTE: The crankshaft pulley bolt has a reverse thread. The crankshaft pulley and bolt are a molded composite and are one piece.
  12. Lower the alternator to allow access to the electrical connectors.
  13. Disconnect the crankshaft sensor.
  14. Release the oxygen sensor connector locator from the bracket.
  15. Remove the lower alternator bolt.
  16. Disconnect the regulator electrical connector.
  17. Disconnect the remaining wiring from the alternator and remove the alternator
To Install:
  1. Position the alternator on the engine while making the necessary electrical connections.
  2. Connect the voltage regulator electrical connector.
  3. Install oxygen sensor connector locator in bracket.
  4. Connect crankshaft sensor.
  5. Raise alternator and install upper alternator bolts (left side bolt is installed with alternator). Torque upper and lower bolts to 18 lb-ft. (25Nm).
  6. Position the wiring harness locator and install nut.
  7. Install the alternator splash shield and the screws.
  8. Position crankshaft pulley and install bolt (reverse thread). Torque to 74 lb-ft. (100Nm)
  9. Remove the flywheel holding tool.
  10. Install the inner fender splash shield.
  11. Install the right front wheel.
  12. Install the torque converter inspection cover.
  13. Lower the vehicle.
  14. Install the power steering hose bracket nut from the alternator mounting bolt.
  15. Install accessory drive belt.
  16. Connect the battery ground cable.
prev.gif next.gif

Jul 18, 2010 | 2006 Ford Taurus

1 Answer

Need to tighten alternator belt


The alternator is held in place by two bolts.

Top and bottom bolts - 12 mill bolts.

By loosening the bolts (especially the top bolt) you will find that the alternator can be manipulated forward and backwards alongs it housing (guides). To tighten the alternator belts all you need to do is push the alternator away from the tensioners and tighten the belt as required.

Once the belt is taut, but not stetched, simply tighten the two bolts up again and check that the belt has not lost its tension when you where tightening the belts.

Feb 19, 2010 | 2004 Mitsubishi Lancer

2 Answers

Alternator removal on 87 acura integra


you need to loosen and remove the alternator mounting bolts and remove the V - belt and alternator assembly.

Dec 05, 2009 | 1987 Acura Integra

2 Answers

How do you get the belt off the alternator?


there is an adjustment for the alternator just need to lossen the bolt and the alternator should slide

Nov 03, 2009 | 1991 Honda Accord

1 Answer

I am changing the alternator in a 1998 dodge neon, need diagram


No diagram...
The pivot bolt is the long bolt that holds the alternator to the frame.
If you loosen it, the alternator can "swing" with the pivot bolt as its .... well, pivot, or swing center.

The long bolt must be removed completely in order to remove the alternator.

Be sure to doisconnect the negative cable from your battery.

Hope this hleps w/o a diagram.

Sep 14, 2009 | 1998 Dodge Neon

1 Answer

HOW HARD IS IT TO REMOVE AN ALTERNATOR


Yes, very easy...here is the steps to do it:

To Remove:
  1. Disconnect battery negative cable.
  2. Remove air cleaner inlet pipe.
  3. Disconnect alternator electrical connections.
  4. Loosen (but do not remove) pivot bolt and tensioner mounting bolt.
  5. Remove drive belt form alternator pulley.
  6. Remove tensioner mounting bolt and belt tensioner.
  7. Remove pivot bolt, loosen adjusting bracket bolt and rotate bracket up.
  8. Remove alternator.

To Install:

  1. Place alternator on engine.
  2. Install (but do not tighten) pivot bolt.
  3. Rotate bracket down on top of alternator.
  4. Install belt tensioner and install bolt loosely.
  5. Install drive belt on alternator pulley.
  6. Tighten tensioner bolt to 14-19 ft lb (19-26 Nm).
  7. Tighten pivot bolt and bracket bolt to 28-38 ft lb (38-51 Nm).
  8. Connect alternator electrical connections.
  9. Install air cleaner inlet pipe.
  10. Connect battery negative cable.

120f25e.gif

Jul 13, 2009 | 1999 Kia Sportage

1 Answer

Need to install an alternator


Removal & Installation
2.7L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Lower plastic splash shield
    • Transmission cooler and position it aside
    • Lower radiator crossmember support
  3. Loosen but do not remove:
    • Adjusting “T” bolt and the pivot bolt
    • Drive belt adjusting bolt
  4. Remove or disconnect the following:
    • Drive belt
    • Alternator field circuit plug
    • Alternator B+ terminal nut and wire
    • Pivot bolt; be careful not to lose the spacer
    • Alternator 0900c152801d4a1e.jpg
    (The location of the generator/alternator on the 2.7L Engine)
To install:
  1. Install or connect the following:
    • Alternator
    • Pivot bolt with the spacer and leave loose
    • Alternator field circuit plug
    • Alternator B+ wire and terminal nut; then, torque the nut to 89 inch lbs. (10 Nm)
    • Drive belt
  2. Usinga belt tension gauge, torque the adjusting “T” bolt until the tensiongauge reads 120 lbs. (534 N) for a used belt or 180–200 lbs. (792–880N) for a new belt.
    • Lower radiator crossmember support
    • Transmission cooler
    • Lower plastic splash shield
    • Negative battery cable
  3. Torque the bolts to the following specifications:
    1. Pivot bolt to 40 ft. lbs. (54 Nm).
    2. 8mm mounting bolt to 30 ft. lbs. (41 Nm).
    3. 10mm mounting bolt to 40 ft. lbs. (54 Nm).

--------------------------------------------------------------------------------------------------------------------------------------------------
3.2L And 3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Lower mounting bolt and pivot bolt
    • Drive belt tension bolt
    • Drive belt
    • Bracket, lower mounting bolt and pivot bolt
    • Alternator
    • Alternator field circuit plug
    • Alternator B+ terminal nut and wire 0900c152801d4a1f.jpg
    (The location of the generator/alternator on the 3.2L and 3.5L engines)
To install:
  1. Install or connect the following:
    • Alternator B+ wire and terminal nut; then, torque the nut to 89 inch lbs. (10 Nm)
    • Alternator field circuit plug
    • Alternator
    • Drive belt
    • Pivot bolt and lower mounting bolt
  2. Usinga belt tension gauge, torque the “V” drive belt until the tension gaugereads 120 lbs. (534 N) for a used belt or 140–160 lbs. (623–711 N) fora new belt.
  3. Using a belt tension gauge, torque the Poly “V”belt until the tension gauge reads 120 lbs. (534 N) for a used belt or180–200 lbs. (792–880 N) for a new belt.
  4. Install the bracket.
  5. Torque the bolts to the following specifications:
    1. Pivot bolt to 40 ft. lbs. (54 Nm).
    2. 8mm mounting bolt to 30 ft. lbs. (41 Nm).
    3. 10mm mounting bolt to 40 ft. lbs. (54 Nm).
  6. Connect the negative battery cable.
Hope this is what you were looking for.

Jan 30, 2009 | 1999 Dodge Intrepid

1 Answer

Need to change the alternator


REMOVAL & INSTALLATION

3.3L Engine:
  1. Disconnect the battery negative - cable.
  2. Disconnect the alternator field circuit plug.
  3. Remove the B+ terminal nut and wire.
  4. Loosen the adjusting T-bolt, but do not remove it.
  5. Loosen the pivot bolt, but do not remove it either.
  6. Remove the alternator drive belt.
  7. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  8. Remove the mounting bolt.
  9. Remove the spacer & washer
  10. Remove alternator.
To install:
  1. Attachthe alternator to the support bracket. Tighten all bracket andalternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Connect the negative - battery cable.
-------------------------------------------------------------------------------------------------
3.5L Engine:
  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
  4. Loosen the belt adjusting bolt.
  5. Remove the alternator drive belt.
  6. Remove the bracket.
  7. Remove the lower mounting bolt and pivot bolt.
  8. Remove the alternator.
  9. Disconnect the alternator field circuit plug.
  10. Remove the B+ terminal nut and wire.
To Install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
If you need photos to follow then try this link...
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528006a83e

Jan 20, 2009 | 1999 Dodge Intrepid

2 Answers

Need to know how to change the alternator properly


There are three bolts: tensioner bolt on bottom two bolts on top and they are tough; three wires: ground, power, and harness.
Disconnect negative battery cable, remove all wires from alternator, remove drive belt. Locate all bolts: remove tensioner bolt and mounting bolts, then remove alternator from below. It comes off easier than it goes back on.
Install is reverse order of removal. be sure to label wires for easier replacement.
This videoclip might help you and you can find for more

Good Luck

Dec 14, 2008 | 1998 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...