Question about Hyundai Cars & Trucks

Open Question

What is the cause and remedy for difficulty in changing gears in a Hyundai atos (2009).Is it the gear adjustor cable?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 566 Answers

SOURCE: manual shift will not engage in gears

hi from uk just out of curiosity ? with engine off try selecting a gear manually by moving the selector link at gearbox from engine compartment if you can feel a selection ? then press clutch and start engine see if car moves with clutch slowly engaged ? if it does? then would suspect the actual g/stick vertical part that fits into the cables gate/selection has broken ? come back with update ? and please give history prior to this fault occuring ?as it would give more of idea what may have gone wrong ?

Posted on Jan 03, 2009

Ad
Benimur
  • 6966 Answers

SOURCE: to change gears, I need to fully press down on my

Hi and welcome to FixYa,

In a manual 2001 Hyundai Accent, the clutch cable could be adjusted. The adjustment point is on the cable 'pad' where it enters the firewall in the engine compartment.
86c2d7d.jpg
To adjust, the slack or free play must be decreased. This is done by turning the adjusting nut clockwise. Check back by pressing on the clutch pedal to your preference.
73309c3.jpg
Good luck and thank you for using FixYa.

Posted on Feb 18, 2009

  • 2 Answers

SOURCE: 1997 sL1 Saturn manual transmission hard to change gears

The dipstick is behind the battery, below the master brake cylinder and is not the clutch reservoir. It has a red flip top handle instead of a ring like most dipsticks. It was hard for me to find due to engine grease. I had the same problem and was able to see that I was low on fluid (only a little) and adding fluid helped the problem. Questions? kurt1431 at comcast dot net.

Posted on Jun 29, 2009

ghost45
  • 1280 Answers

SOURCE: vehicle wont change up into gear reverse gear not

P0734 - 4th gear incorrect ratio. P1529 Malfunction Indicator Lamp Request. Problem is in the transmission.
Take/Tow your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it.

Posted on Oct 03, 2009

ghost45
  • 1280 Answers

SOURCE: 2001 Hyundai - reverse gear is inoperative. The

If I understand you correctly, you have ALL forward gears working, but reverse doesn't?... then the problem is in the transmission itself or the linkage on the trans linkage into reverse.

Posted on Oct 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace cam position sensor


The Atos has a timing sensor located at the bottom of the engine by the cambelt drive sprocket (gear). The drive sprocket is bolted to the crankshaft with a timing plate. The sensor is placed next to the timing belt.There are no cam timing sensors on the cylinder head. This is a very basic engine.

Jun 10, 2014 | 2006 Hyundai Atos 1.1

1 Answer

Hyundai atos 2006 clutch pedal hard and gears change difficult


After replacing the clutch and adjusted the cable and you are STILL having a problem with the clutch (it is a cable clutch not a hydrolic one) have a look at where the clutch enters through the fire wall (engine side) you will see that is has probably collapsed or dented there, for some reason this is a common occurrence with the hyundai. This has happened to mine as well as my friend's atos. This is something that should not happen

Aug 04, 2013 | Cars & Trucks

1 Answer

Hyundai Atoz Tiptronic gearbox not engaging in gear


you may have to have the gear box replaced or it may be a sensor or seliniod

Jan 24, 2013 | 1998 Hyundai Atos

2 Answers

Hyundai atoz dosent pick up speed at high gear and start jerking


fuel pressure cud be bad at that speed--transmission may hav issue in top gear--find a specialist to test--------

May 08, 2012 | 2006 Hyundai Atos 1.1

2 Answers

Hyundai atos crank sensor keeps failing


I know this post is very old, but nonetheless I hope this helps anyone else researching this problem.
The cam belt gear located on the crankshaft wears done on the inside of the gear. This causes the gear to "wobble" and hence touch the timing sensor, which damages it and results in its failure.
This wearing of the gear is by design and Hyundai should be taken to task for this. The crankshaft does not have a key between it and the gear. The crankshaft has "flattened" sides which match the gear and prevents it from "slipping" on the shaft, but with time the flattened edges of both the crank and the gear wear out and the gear wobbles slightly. This then accelerates the damage and can cause the gear to begin to cut into the aluminium engine cover and the main oil seal.
The only resolution is a new crankshaft and gear or sell the car.
I have had my battles with Hyundai and did not win, even though i could show a design fault.
I hope someone out there can take these guys to task and actually win and so create a precedence for the rest of us.

Good Luck

3_2_2013_10_57_32_pm.jpg


3_2_2013_11_00_19_pm.jpg

Mar 08, 2012 | 2006 Hyundai Atos 1.1

1 Answer

How to use hyundai atos overdrive


there is a simple button beside your transmission handdy.. just press it, you will see on your screen "OD off", which it means your gearbox will not go to overdrive gear(usually 4th gear called overdrive) and it will not go more than 3th gear.

Feb 16, 2012 | Cars & Trucks

1 Answer

Gear stick vibration only in 3rd gear @ 2500 rpm on my new 2009 Tucson 2l any idea what causes this,as dealer says new "PART" needs to be fitted


My brand new 2009 Tucson has the same problem. My dealer said it needs a 3rd Gear Kit fitted.
They are on back order as a number of other Tucson's have the same problem. I may have to wait 3 months for the part.
My dealer has ordered 126 back order parts for this problem.


Nov 18, 2009 | 2009 Hyundai Tucson

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...