Question about MG Cars & Trucks

Open Question

Heater hose routing for a 1979 mg midget 1500 engine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
farroutideas
  • 78 Answers

SOURCE: need diagram of heater hose route from engine to rear heater

Hi there;

I found a couple pictures; I wasn't sure of your engine size or if you needed the rear heater aplication so I picked the most common ones & attached them.

bc4b1f6.jpgbde0533.jpg
Good luck; Hope this helps
Farrout!

Posted on Mar 18, 2009

Ad
  • 434 Answers

SOURCE: I need to know what to buy to rebuild the differential

Ring and pinion gears and a master bearing set. The bearing set should come with all bearings, crush sleeves, etc..

Posted on Jul 01, 2009

  • 4 Answers

SOURCE: I need a vacuum hose routing diagram for a 1987

See if this diagram is what your looking for.


Posted on Sep 14, 2009

  • 9 Answers

SOURCE: mg midget 1275 [1974] runs very lumpy..wont run

check distributor advance mechanism(below points)the weights and springs could be stuck or broke

Posted on Nov 18, 2009

  • 4793 Answers

SOURCE: I HAVE A 1982 AUSTIN

it will do no harm at all.in fact ANY battery with the correct terminals will do.

Posted on Nov 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mg midget rear lights flash when indicator are on


Sounds like a ground issue in you rear tail lamps. When the lights are not receiving proper ground, they will tend to do wonky things as they attempt to find a ground through other circuits.
Also, if the car happens to have a trailer hitch (yes, I have seen MG Midgets with trailer hitches, haha) then start by checking the wiring for the trailer circuit for wires shorted out against each other or otherwise damaged.

Oct 12, 2017 | MG Cars & Trucks

1 Answer

How to adjust achoke on 1979 mg 94 cubic engine has antifreeze running through it


You need to calibrate the heat mass before reassembling the choke unit. This is from John Twist of University Motor. Hope it helps.

Loosen the 1/2" headed bolt that fastens the water jacket to the heat mass. Then, disconnect the two hoses from the water jacket and plug them with 7/16" bolts. Remove the bolt the rest of the way and CAREFULLY lever the water jacket away from the heat mass. Then, remove the three screws that hold the heat mass to the auto choke.

Remove the heat mass and carefully remove the black plastic insulator. Now you can work with the auto choke and calibrate the heat mass.

Copiously oil the inside of the autochoke, and exercise it -- hold the throttle wide open and move the little lever which engages the bi-metal strip of the heat mass from its 3:00 position to the 12:00 position -- about twenty times.

Place the heat mass in a pan of water and bring it to a boil. Pick the heat mass from the boiling water and inspect the alignment of the bi-metal strip -- well, really the rectangle -- and the line scribed in the circumference of the heat mass. That line is usually ill-defined or worse, completely obliterated. Cut a new line with your hacksaw wherever the rectangle is positioned.

Now reassemble the unit, taking GREAT care to match the finger of the choke with the rectangle of the bi-metal strip. Position all three lines (the boss on the auto choke body, the raised line on the black plastic insulator, and the line you just made with the hacksaw), in line.

Feb 25, 2015 | 1956 MG Midget TF

2 Answers

Mg midget troubleshooting


The servo is not fitted correctly. Take it off and re fit it. The engine vacuum is operating the brakes too soon.

Jun 19, 2014 | 1957 MG Midget

1 Answer

Need wire diagram for 1867 mg midget


You can get one on Ebay, or just use MSN.com or Bing for "1967 MG Midget Wiring Diagram, and they show images of it you can copy! They are usually about $12.00 and up on Ebay!

Apr 18, 2014 | Cars & Trucks

1 Answer

Why car is running rough


It is most likely a carburetor problem. MGs are known for their dual carb set up. Heres a you tube video on how to tune them. https://www.youtube.com/watch?v=4nvGLgO6pj0

Mar 31, 2014 | 1957 MG Midget

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top MG Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Bryan Mcphee
Bryan Mcphee

Level 1 Expert

23 Answers

Are you a MG Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...