Question about Ford Cars & Trucks

Open Question

Engine diagram 1990 ford festival 1.3 or way to locate egr valve

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1596 Answers

SOURCE: 1990 ford f150 cross over valve location

Please Help ME by Remembering to RATE ME Thank you Vrey Much !!!

This vehicle does not use an external fuel tank switching valve. A supply check valve in the fuel pump assembly opens when the outlet pressure from the energized fuel pump exceeds the opposing check valve spring force.


R E C A L L 1991
THE DUAL FUEL TANK SELECTOR VALVE MAY MALFUNCTION AND CAUSE AN OVERFILL CONDITION IN ONE OF THE FUEL TANKS, RESULTING IN AN OVERFLOW OF FUEL PAST THE FILLER CAP.
THE OVERFLOW OF FUEL PAST THE FILLER CAP CAUSES A FUEL LEAKAGE, WHICH CAN RESULT IN A FIRE WHEN EXPOSED TO A SOURCE OF IGNITION.
REPLACE THE DUAL FUEL TANK SELECTOR VALVE.
SYSTEM: FUEL TANK, AUXILIARY.
VANS AND LIGHT TRUCKS WITH DUAL FUEL TANKS PRODUCED IN THE FOLLOWING PERIODS: F150, F250, AND F350 LIGHT TRUCKS BUILT BETWEEN FEBRUARY 28, 1989 AND JULY, 1989; ECONOLINE BUILT BETWEEN FEBRUARY 28, 1989 AND FEBRUARY 11, 1991.
NOTE: FORD HAS AGREED TO RECALL THESE VEHICLES BUT PARTS ARE NOT YET AVAILABLE.PARTS WILL BE AVAILABLE IN DECEMBER 1991. YOU WILL RECEIVE A LETTER FROM FORD ADVISING YOU WHEN TO SCHEDULE AN APPOINTMENT WITH YOUR DEALER TO HAVE THE RECALL WORK PERFORMED. IN THE MEAN TIME, YOU CAN TAKE THE FOLLOWING PRECAUTIONS:FILL EACH TANK TO ONLY 1/3 FULL. IF YOUR VEHICLE LEAKS FUEL OR IF YOU SMELL FUEL, STOP USING THE VEHICLE AND CALL FORD AT (313) 446-4654 AND ADVISE THEM OF YOUR PROBLEM. REFER TO FORD SAFETY RECALL NUMBER 91S39. AN OPERATOR WILL TAKE YOUR NAME AND TELEPHONE NUMBER. A FORD REPRESENTATIVE WILL CALL YOU BACK

Posted on Jan 21, 2009

  • 840 Answers

SOURCE: where is my egr valve

Oks it should be close to fire wall it looks around 3 inches oval shaped and has 2 bolts in it and has a gasket plus it has a wired connector to it so you should replace the gasket after you clean it/ so tak it out and use carb cleaner any kind / Put an ew gasket on after you klean it and plug it back in try that/ Please rate my response/ Thank you very much

Posted on Jan 29, 2009

c17hydro
  • 2984 Answers

SOURCE: location of EGR valve for 4.6 liter engine

a887903.gif
EGR VALVE IS #2.

Please wait for second post to answer your second question....comes with a few pictures.

Posted on Nov 16, 2009

Testimonial: "thanks c17hydro ...looks like the proper proceedure,,,will try fix tomorrow"

  • 8 Answers

SOURCE: Need a pic veiw of 2004 ford f350 6.0L diesel EGR

1st of all when Ford started out with putting "EGR's" on those diesel engines, they rushed it and are nothing less than a pain in the ***! i recommend having an EGR cleaning service performed by your local Ford dealer, i know they charge up the wazoo, but they're the best people to perform the service period.this is a VERY common problem with those engines and that service is "supposed" to be performed every 30K I believe. i dont recommend attempting to remove and service it youself, this WILL only make it worse.

Posted on Mar 26, 2010

Testimonial: "Im relieved to here that someone else is thinking the same thing. Im still going to try it myself as i am somewhat skilled at this but Thanks a bunch!"

toneman2121
  • 775 Answers

SOURCE: egr valve replacement diagram. cant find location

her is a forum with a similar reqeust. you may be able to find information at the hyundai site this gentleman suggests.

http://en.allexperts.com/q/Hyundai-Repair-815/2003-Santa-Fe-2-2.htm

Posted on Jun 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Egr system diagram 1996 ford contour


the two hoses for the egr should run from the exhaust manifold to what is called the dpfe sensor. this sensor is usually located on the firewall or the engine

Oct 17, 2015 | 1996 Ford Contour

1 Answer

My 1990 ford festival is cutting out when accelarating


Sounds like it may be your EGR valve. I'd take a look at the PCV valve first since its the less expensive one to replace and can cause a similar issue.

Oct 18, 2014 | 1990 Ford Festiva

2 Answers

Where is the egr valve on a 99 Ford expedition


The EGR valve is in a very difficult spot to work on. If the EGR is bad it will set off the check engine light and make the vehicle run rough or stall at idle. It really doesn't make it run rough while driving or accelerating. What are the conditions when the car runs rough?

Mar 01, 2014 | 1999 Ford Expedition

2 Answers

Need to find and replace the DPFE-15 sensor. Dealership diagnosed when service engine light came on and saaid this is what needed replacing. Problem is I do not know where to find it on the engine.


Exhaust Gas Recirculation (EGR) System The exhaust gas recirculation (EGR) system is designed to:
  • reintroduce exhaust gas into the combustion cycle.
  • lower combustion temperatures.
  • reduce the formation of oxides or nitrogen (NOX).
The amount of exhaust gas reintroduced and the timing of the cycle varies by calibration. Timing and volume are controlled by the following:
  • engine rpm
  • engine vacuum
  • exhaust system back pressure
  • engine coolant temperature
  • air charge temperature
  • throttle position
The EGR valve (EGR valve) (9D475) is vacuum-actuated. The vacuum hose routing diagram is shown on the Vehicle Emission Control Information (VECI) decal. The EGR system is a differential pressure feedback EGR Sensor system. Differential pressure feedback EGR Sensor is a subsonic closed loop EGR system. The differential pressure feedback EGR system:
  • monitors EGR flow rate by the pressure drop across the metering orifice located in the EGR tube.
  • uses a differential pressure feedback EGR sensor as the feedback device.
  • uses the EGR valve only as a pressure regulator, rather than a flow metering device.
  • controlled pressure is varied by the valve movement using vacuum output of the EGR vacuum regulator solenoid (9J459).
  • allows for a more accurate assessment of EGR flow requirements.


Differential Pressure Feedback EGR Flow Diagram


aa3104a.gif

Differential Pressure Feedback EGR Sensor Removal
  1. Disconnect engine control sensor wiring (12A581) from Differential Pressure Feedback EGR Sensor.
  1. Disconnect Differential Pressure Feedback EGR Sensor hoses from EGR valve to exhaust manifold tube (9D477).
  1. Remove retaining nuts or bolts (depending upon application) and EGR Differential Pressure Feedback transducer.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten retaining nuts or bolts (depending upon application) to 5-7 Nm (45-61 lb-in).


    Differential Pressure Feedback EGR Sensor, 3.0L (2V) Engine


    aa0036a.gif



    Differential Pressure Feedback EGR Sensor, 3.0L (4V) Engine


    a23840a.gif


    Item Part Number Description 1 6049 RH Cylinder Head 2 - Differential Pressure Feedback EGR Sensor 3 - Nut (2 Req'd) 4 - Stud Bolt 5 - Bolt (2 Req'd) 6 - Differential Pressure Feedback EGR Sensor Bracket A - Tighten to 5-7 Nm (45-61 Lb-In) B - Tighten to 8-12 Nm (71-106 Lb-In)

    Engine Emission Control Component Location-3.4L SHO Engine


    a25013a.gif


    Item Part Number Description 1 95607-05200 Nut 2 - EGR Sensor Hose 3 - EGR Sensor Hose 4 95027-08016 Bolt 5 - Differential Pressure Feedback EGR Sensor 6 9J433 Differential Pressure Feedback EGR Sensor Mounting Bracket 7 9D474 EGR Solenoid Vacuum Valve (2 Req'd) 8 A4670 Vacuum Tube Assembly 9 9424 Intake Manifold 10 9J459 EGR Vacuum Regulator Solenoid A - Tighten to 5-7 Nm (45-61 Lb-In)
Hope this helps

Aug 14, 2011 | 1999 Ford Taurus

2 Answers

Having trouble locating the erg valve


Please let me know if you have more questions, and thanks for using FixYa.

3.0 liter:

jturcotte_1407.gif

SHO:

jturcotte_1408.gif

3.8:

jturcotte_1409.gif

2.5:

jturcotte_1410.gif

Apr 02, 2011 | 1990 Ford Taurus

2 Answers

Where do I find the EGR Pressure Sensor on a 1998 Ford Taurus 24V DOHC Engine


it is near the EGR valve it has two small hoses going to it, see photo below, it is called the DPFE sensor.


26cb75c.jpg

Apr 25, 2010 | 1998 Ford Taurus

1 Answer

Code P0402, on 2005 Freestyle. Where is the valve


I assume (based on the code) that you are referring to the egr valve. Here is a picture showing an EGR valve (not from the freestyle):http://i133.photobucket.com/albums/q48/tommyliuca/egr%20valve/1-1.jpg

The freestyles looked similar and is in a similar location. Looking at the engine from the front of the car, the EGR valve is to the right of the engine and a little further back (closer to the driver).

Let me know if you can find it, or if you need a picture of the freestyle's (I own a 2005 freestyle).

Jan 25, 2010 | 2005 Ford Freestyle

1 Answer

WHERE IS THE EGR VALVE ON A 1990 OLDSMOBLE CUTLASS SUPREME LOCATED AT


6ff5ad5.jpg About $140.00

The EGR valve is mounted on the intake manifold and has an opening into the exhaust manifold.

The digital EGR valve, used on all 1990 and later EGR-equipped engines (Except the 2.5L and 1994-96 3.8L engine) is designed to control the flow of EGR independent of intake manifold vacuum. The valve controls EGR flow through 3 solenoid-opened orifices, which increase in size, to produce 7 possible combinations. When a solenoid is energized, the armature with attached shaft and swivel pintle, is lifted, opening the orifice.
The digital EGR valve is opened by the ECM, grounding each solenoid circuit individually. The flow of EGR is regulated by the ECM which uses information from the Coolant Temperature Sensor (CTS), Throttle Position Sensor (TPS) and Manifold Absolute Pressure (MAP) sensor to determine the appropriate rate of flow for a particular engine operating condition.

Digital EGR Valve Testing:

This system must be checked using a Tech 1®or equivalent scan tool. Steps 4, 5 and 6 must be done very quickly, as the ECM will adjust the idle air control valve to compensate for idle speed.
  1. Using a Tech 1®or equivalent scan tool, check for any diagnostic trouble codes and solve those problems first. Refer to the Diagnostic Trouble Code (DTC) lists later in this section.
  2. Select "EGR CONTROL'' on the scan tool.
  3. Start and run the engine, until it reaches normal operating temperature, then allow the engine to idle for 2 minutes.
  4. Energize EGR SOL #1; engine rpm should drop slightly.
  5. Energize EGR SOL #2; the engine should have a rough idle.
  6. Energize EGR SOL #3; the engine should idle rough or stall.
  7. If all tests were as specified, the system is functioning properly.
  8. If not, check the EGR valve, pipe, adaptor, gaskets, fittings, and all passages for damage, leakage or plugging. If all is OK, replace the EGR valve assembly.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 02, 2009 | 1990 Oldsmobile Cutlass Supreme Conv

2 Answers

Location of the egr sensor on 2000 ford ranger


The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Feb 24, 2009 | 2000 Ford Ranger SuperCab

2 Answers

EGR VALVE ON 96 FORD PROBE SE


If it's a 2.0L, 5 speed (1994-7) there are two DPFE solenoids (both w/ 3 vacuum ports) near the oil filter, which control the EGR valve. They are discontinued and impossible to find except on junked cars. (FORD #'s K5T44093-4)
I have to junk my 1996 Probe if I don't find them - Missouri emissions.

Aug 24, 2008 | 1996 Ford Probe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...