Question about Ford Cars & Trucks

Open Question

Where is the egr !located at on 1990 ford festival 1.3 litter

Egr valve location

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 333 Answers

SOURCE: WHERE DO I LOCATE THE EGR VALVE ON MY 2001 CHEVY IMPALA 3.8 V6

The egr valve is located at the end of a hose that plugs into youe valve cover. It is pushed right into a rubber grommet that is located in one of the valve covers. I hope this helps. don.t forget to rate my nswer, thanks

Posted on Feb 27, 2009

emissionwiz
  • 75807 Answers

SOURCE: where is the egr valve located on a 1999 silverado 5.3 vortec

try cleaning the inside of the MAF sensor with CRC brand MAF cleaner, it is availiable at any auto parts store for around $5

Posted on Feb 27, 2009

  • 323 Answers

SOURCE: EGR Location

On the left side at the rear of the engine, and it isn't fun to change.

Posted on May 29, 2009

ZJLimited
  • 17970 Answers

SOURCE: egr valve location on dodge ram 2005 4.7

The EGR, or exhaust gas recirculation valve, takes inert exhaust gasses drawn from the exhaust system and reintroduces them into the combustion chamber through the intake manifold. This process lowers the peak combustion temperature and helps combat the formation of Nitrous Oxide (NOx) in the exhaust.

f0255cf.jpg

  1. Separate the intake ducts from the air cleaner assembly by loosening the retaining clamps and pulling the ducts away from the housing.
  2. Disconnect the vacuum line from the air cleaner assembly.
  3. Remove the wing nut that secures the air cleaner housing lid to the base.
  4. Remove both the air cleaner hosing lid and base.
  5. Locate the EGR valve. Look at the front of intake manifold. The EGR valve will be bolted to the intake manifold just in front of the carburetor.
I hope help you with this. Good luck.

Posted on Sep 07, 2009

c17hydro
  • 2984 Answers

SOURCE: location of EGR valve for 4.6 liter engine

a887903.gif
EGR VALVE IS #2.

Please wait for second post to answer your second question....comes with a few pictures.

Posted on Nov 16, 2009

Testimonial: "thanks c17hydro ...looks like the proper proceedure,,,will try fix tomorrow"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1990 ford festival is cutting out when accelarating


Sounds like it may be your EGR valve. I'd take a look at the PCV valve first since its the less expensive one to replace and can cause a similar issue.

Oct 18, 2014 | 1990 Ford Festiva

2 Answers

Where is the egr valve on a 99 Ford expedition


The EGR valve is in a very difficult spot to work on. If the EGR is bad it will set off the check engine light and make the vehicle run rough or stall at idle. It really doesn't make it run rough while driving or accelerating. What are the conditions when the car runs rough?

Mar 01, 2014 | 1999 Ford Expedition

1 Answer

Location of egr valve on 92 ford f150 pickup 4.9 l


it means its time to replace the EGR (exhaust gas recirc) valve it will be located on your intake manifold.

Mar 14, 2012 | 1991 Ford F150

2 Answers

Having trouble locating the erg valve


Please let me know if you have more questions, and thanks for using FixYa.

3.0 liter:

jturcotte_1407.gif

SHO:

jturcotte_1408.gif

3.8:

jturcotte_1409.gif

2.5:

jturcotte_1410.gif

Apr 02, 2011 | 1990 Ford Taurus

1 Answer

Where is the egr valve & position sensor located on a 1995 ford f-350 with a 460


The egr valve is located on the valve cover and has a 1/2 hose connected to it going to air cleaner.
The position sensor is located at the front bottom of motor it is looking at the harmonic balancer at the front bottom pulley under the fan blade pully.

Jul 12, 2010 | 1995 Ford F350

1 Answer

WHERE IS THE EGR VALVE ON A 1990 OLDSMOBLE CUTLASS SUPREME LOCATED AT


6ff5ad5.jpg About $140.00

The EGR valve is mounted on the intake manifold and has an opening into the exhaust manifold.

The digital EGR valve, used on all 1990 and later EGR-equipped engines (Except the 2.5L and 1994-96 3.8L engine) is designed to control the flow of EGR independent of intake manifold vacuum. The valve controls EGR flow through 3 solenoid-opened orifices, which increase in size, to produce 7 possible combinations. When a solenoid is energized, the armature with attached shaft and swivel pintle, is lifted, opening the orifice.
The digital EGR valve is opened by the ECM, grounding each solenoid circuit individually. The flow of EGR is regulated by the ECM which uses information from the Coolant Temperature Sensor (CTS), Throttle Position Sensor (TPS) and Manifold Absolute Pressure (MAP) sensor to determine the appropriate rate of flow for a particular engine operating condition.

Digital EGR Valve Testing:

This system must be checked using a Tech 1®or equivalent scan tool. Steps 4, 5 and 6 must be done very quickly, as the ECM will adjust the idle air control valve to compensate for idle speed.
  1. Using a Tech 1®or equivalent scan tool, check for any diagnostic trouble codes and solve those problems first. Refer to the Diagnostic Trouble Code (DTC) lists later in this section.
  2. Select "EGR CONTROL'' on the scan tool.
  3. Start and run the engine, until it reaches normal operating temperature, then allow the engine to idle for 2 minutes.
  4. Energize EGR SOL #1; engine rpm should drop slightly.
  5. Energize EGR SOL #2; the engine should have a rough idle.
  6. Energize EGR SOL #3; the engine should idle rough or stall.
  7. If all tests were as specified, the system is functioning properly.
  8. If not, check the EGR valve, pipe, adaptor, gaskets, fittings, and all passages for damage, leakage or plugging. If all is OK, replace the EGR valve assembly.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 02, 2009 | 1990 Oldsmobile Cutlass Supreme Conv

2 Answers

Location of the egr sensor on 2000 ford ranger


The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Feb 24, 2009 | 2000 Ford Ranger SuperCab

2 Answers

2005 Dodge 1500 code p0404 EGR valve.


The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Feb 05, 2009 | 2005 Dodge Ram 1500

2 Answers

EGR VALVE ON 96 FORD PROBE SE


If it's a 2.0L, 5 speed (1994-7) there are two DPFE solenoids (both w/ 3 vacuum ports) near the oil filter, which control the EGR valve. They are discontinued and impossible to find except on junked cars. (FORD #'s K5T44093-4)
I have to junk my 1996 Probe if I don't find them - Missouri emissions.

Aug 24, 2008 | 1996 Ford Probe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...