Question about Cars & Trucks

1 Answer

They say they cannot find 043. This is what is on my machine 46788 043-5488-8

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Http://www.manualsonline.com/support/other/air-conditioner/manual-5487384

Posted on Aug 09, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What should the spark plug gap be set to?


the spec is .043", for both the V6, and the Inline 4. The theory behind enlarging gaps, is that a larger gap creates a larger spark, thus more effecient ignition. The problem is, your ignition system was designed for the .043" spark plug gap, not larger. Enlarging the gap puts a greater strain on your ignition system components, and it may not be strong enough to jump a larger gap. The result would be less efficient combustion, or a cylinder(s) that won't fire at all. Pull your plugs, and set them at .043". Check the distributor cap, rotor, wires, and your filters. Make sure the car is totally warmed up before the smog test. Good luck.

Jun 04, 2016 | 1990 Toyota Corolla

1 Answer

What is the gap setting for the spark plugs a 2004 trailblazer?


I have been told by mechanics and 2 auto stores that the gap should be .043. I don't know where people are getting .060. but my plugs are .043 and my trailblazer does not misfire or run poorly. Also, check the gap always, even if it's pre gapped because the handling of spark plugs could cause a change in gap. IE the plug bouncing in the box, vibration, etc.

Aug 23, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

How to replace rear wheel bearing on 1994 bmw 325i


3-Series (Except M3, M Roadster, M Coupe, 318ti & Z3)

1. Raise and support vehicle. Remove wheel(s).
2. Remove axle shaft. See appropriate AXLE SHAFTS article.
3. Remove brake disc. See BRAKE DISC .
4. Screw special tool (33 2 116) onto drive flange with wheel studs. Drive out drive flange with special tool (33 4 201/202/203). See Fig. 33.
5. If necessary, pull off bearing inner race using special tool (00 7 500) and a thrust piece. See Fig. 34.
6. It may be necessary to remove inner wheel bearing race with the following procedure:
  • Detach wheel bearing inner race with special tool (33 4 400) through groove in bearing inner race.
  • According to outside diameter of bearing inner race, use special tool 33 4 401 with: 33 4 405 for dia. 45-51 mm, 33 4 406 for dia. 50-55 mm and 33 4 407 for dia. 55-61 mm in groove. See Fig. 35.
  • Tension special tool 33 4 401 with wrenches 33 4 403 and 33 4 404 until it can still just be turned in groove. See Fig. 36 .
  • Screw in special tool 33 4 402. Detach inner bearing race.
7. Remove circlip. See Fig. 37 .
8. Remove wheel bearing with special tool 33 4 031/ 041/ 042/ 043/ 045. See Fig. 38 .

CAUTION: Do not reuse old wheel bearing.

9. Draw in new wheel bearing with special tool 33 4 041/ 042/ 043/ 047. For inner bearing race 42 mm use special tool 33 4 049 and for 39 mm use 33 4 046. See Fig. 39 .
10. Installation is reverse of removal.
11. Replace stretched or damaged circlip. Ensure correct seating.
12. Pull in drive flange using special tool 33 4 041/ 042/ 043/ 045/ 048. See Fig. 40 .
13. Install brake disc.
14. Install axle shaft.


91stt_11.jpg

91stt_12.jpg

91stt_13.jpg

91stt_14.jpg

91stt_15.jpg

91stt_16.jpg

91stt_17.jpg

91stt_18.jpg

Nov 12, 2010 | BMW 325 Cars & Trucks

1 Answer

What is the spark plug gap for a 1993 2.2 honda accord


Look on the emissions sticker under the hood, or in the owners manual. If you don't have either, it should be between .039 and .043.
I would go .042.

Nov 07, 2009 | 1993 Honda Accord

1 Answer

What is the correct spark plug gap setting for a 2001 Honda Accord with a 3.0 V6


Typically that vehicle would need about .043. However, use NGK plugs and do not drop them, and they will be gapped correctly...

Sep 20, 2009 | 2001 Honda Accord

1 Answer

What does Code 043 Mean?


Engine misfire in one or more cylinders. Vehicle been acting up?

Jul 08, 2009 | 1996 Chrysler Town & Country

1 Answer

I am changing the spark plugs on my 2002 GMC Envoy. I need to know what the gap will be


.043. Good luck. Thanks for rating my response and for using FixYa!

Jun 28, 2009 | 2002 GMC Envoy

1 Answer

Need diagram for serpentine belt on a 2003 monte carlo


http://gsi.xw.gm.com/image_en_us/gif/000/000/043/43400.gif

Jan 11, 2009 | 2003 Chevrolet Monte Carlo

2 Answers

Bosch Injectors for a 1972 Citroen DS 21 IE


If you put larger injectors in the engine without the proper fuel management then all you are going to do is run rich and get horrible gas mileage. The only way you will need larger injectors is if you have forced induction or a full motor high compression build.

Jun 03, 2008 | 1989 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...