Question about Cars & Trucks

Open Question

Transmission oil pan removal2004 nissan quest

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2001 Nissan Altima Transmission Oil pan

Dealer is the best option...i just had to replace mine and it was about 40.00

Posted on Dec 13, 2008

  • 42 Answers

SOURCE: How to remove oil pan?

Junkyard for the pan. Either that or go an import specific shop, they should be able to at least you find one.
I highly doubt that you have to drop the whole engine. You shouldn't have to completely remove the transaxle to pull the oil pan but you probably do have to pull a few bolts.  By the way, if your oil pan is leaking, you can most likely just replace the oil pan gasket unless it is really warped.

Posted on Mar 10, 2009

  • 6982 Answers

SOURCE: Oil pan removal on a 97 jeep wrangler

Instructions can be found in any basic manual but the simple version is to remove anything obvious that will be in your way (starter, trans lines etc). Disconnect both engine mounts and raise engine to get better clearance (watch stuff on top so you don't break anything) I usually stuff a couple of 2x4 wood blocks between engine & mounts to support it. Remove all pan bolts and take it down (remember pump pickup will interfere) Do what you need to do, then reverse process.

Posted on Jun 12, 2009

  • 400 Answers

SOURCE: Oil pan removal- 12 point bit size?

I don't know what size they are, but the sockets are available at auto parts stores. They may know the size or you could try a couple to get the right one. I hope this helps you.

Posted on Nov 07, 2009

  • 14585 Answers

SOURCE: I'm trying to remove my oil pan on a 2000

I am not sure, But there could be six more bolts to remove. They will be on the side of the pan, about half way up. three on each side. Sorry for guessing, I work on to many makes and models. Also the gaskets do hold the pan on tight sometimes. If there are no extra bolts then carefully pry it off.

Posted on Feb 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove oil pan



4x4
1. Open the hood.
2. Disconnect the battery negative cables.
3. Remove the intake air assembly.
4. Remove the radiator shroud retaining bolts.
5. Install engine support fixture # 8534B .
6. Raise and support the vehicle.

WARNING: HOT OIL CAN CAUSE PERSONAL INJURY.


7. Drain the engine oil (Refer to 09 - Engine/Lubrication/OIL - Standard Procedure) .
8. Loosen the front engine mount bolts.
9. Lower the vehicle.
10. Use the engine support fixture # 8534B to raise engine out of the front mounts.
11. Remove the engine oil dipstick.
12. Raise and support the vehicle.
13. Remove oil pan bolts, break the pan to block seal, and lower pan slightly and remove oil suction tube fasteners.
14. Remove oil pan and suction tube.
15. Remove the 2 bolts from the front of the engine block stiffener.
16. Remove the oil pan.


4x2
1. Open the hood.
2. Remove the negative battery cables.
3. Raise and support the vehicle.
4. Remove the transmission oil cooler lines.
5. Remove the propeller shaft.
6. Remove the starter bolts.
7. Support the starter.
8. Remove the torque converter bolts.
9. Remove the exhaust hanger bolts.
10. Remove the gear shift cable.
11. Remove the wiring harness.
12. Remove the transmission mount.
13. Remove the crossover bolts.
14. Position the transmission jack.
15. Remove the bell housing bolts.
16. Remove the transmission.
17. Remove the flywheel housing bolts (8).
18. Remove the flex plate bolts (8).
19. Remove the engine oil dip stick.
20. Drain the oil.
21. Remove the steering rack bolts.
22. Remove the oil pan bolts.
23. Remove the oil pickup bolts.
24. Remove the oil pan. user_online.gif

Aug 01, 2014 | Dodge Ram 3500 Cars & Trucks

1 Answer

How to change a transmission fluid filter


You have to remove the transmission oil pan to access the transmission fluid filter. The bolts are turned counter clockwise to remove and clockwise to install (righty tighty, lefty loosey). The biggest problem you will have is the transmission oil leaking from the pan after you replace the transmission pan. Look up the details on proper installation of the pan. Also, check your manual (at local library) to see if their are going to be any obsticles you will have to remove that might be on top of the transmission pan or in the way of the transmission pan. And please don't under-fill, over-fill, use cheap transmission oil or the wrong type of transmission oil. Make sure you use the kind of transmission oil that your vehicle manufacture recommends. Have plenty of rags on hand. Put some cardboard under your vehicle to catch any spills.

Jun 30, 2014 | 2006 Hyundai Tucson

1 Answer

Where is transmission filter located in 2001 mitsubishi diamante located and how do i change it?


transmission filter in the bottom of transmission bolted to valve body.you need a large drain pan.place drain plug under transmission oil pan.remove transmission oil pan drain plug.let all transmission fluid drain out then screw back drain plug in oil pan.then you need to remove transmission oil pan then remove filter and replace pan gasket also.make sure you have right amount transmission fluid on hand.buy extra because if you short of fluid you cant drive car if fluid level too low.make sure you get the right amount fluid.torque pan bolts to 96 inch pounds.

Nov 10, 2011 | 2001 Mitsubishi Diamante

1 Answer

How to do a transmission fluid/filter change on a gmc 1500 2wd v8 350 step by step


Raise the vehicle. Refer to Vehicle Lifting. Place a drain pan under the transmission oil pan. Remove the oil pan drain plug. Remove the oil pan bolts. Remove the oil pan. Remove the gasket. Remove the magnet. Remove the oil filter. Remove the filter neck seal. The transmission oil pan gasket is reusable. Inspect the gasket and replace as needed. Clean the transmission case and the oil pan gasket surfaces with solvent. Install the filter neck seal. Install the oil filter. Install the oil pan gasket to the pan. Install the magnet into the bottom of the pan. Notice: Refer to Fastener Notice in Service Precautions. Install the oil pan to the transmission with seventeen bolts. Tighten the oil pan bolts to 11 Nm (97 inch lbs.) . Apply a small amount of sealant GM P/N 12346004 to the treads of the drain plug. Install the oil pan drain plug. Tighten the oil pan drain plug to 18 Nm (13 ft. lbs.) . Install Dextron Automatic Transmission Fluid. Lower the vehicle.

Jul 04, 2011 | GMC Sierra 1500 Cars & Trucks

2 Answers

HOW DO I REPLACE A SHIFT SILENOID IN A 1998 CHEVY VAN 1500


This is on a 4L60-E--Automatic Transmission

michael_cass_182.jpg
This is on a 4L80-E--Automatic Transmission


michael_cass_183.jpgHope this helps you ??

Jun 27, 2011 | 1998 Chevrolet Express

2 Answers

How difficult is it to change the oil pan on a 1997 gmc jimmy 4x4?


4WD To Remove:
  1. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator
    • Front differential assembly
    • Starter
    • Transmission cover
    • Oil pan drain plug and drain the engine oil into a suitable container
    • Remote oil filter pipe adapter
    • Remote oil filter hose clip bolt on oil pan
    • Starter wire harness bracket stud
    • Transmission oil cooler pipes (if equipped)
    • Access plugs for oil pan rear nuts
    • Transmission to oil pan bolts
    • Oil pan nuts and bolts gm_truck_43_ol-pn_ol-lvl-snsr.gif

      NOTE: The low oil level sensor is not reusable.
    • Remove and discard the engine oil level sensor (if applicable) gm_truck_43_ol-pn_blts.gif

    • The oil pan
    • The oil pan gasket
  2. Discard the oil pan gasket.
  3. Clean all sealing surfaces on the engine and the oil pan.
To Install:
Note: Whenever the transmission and the engine oil pan are removed from the engine at the same time install the transmission before the oil pan. This is to allow for the proper oil pan alignment. Failure to achieve the correct oil pan alignment can result in transmission failure.
  1. Apply a 0.197 inch (5 mm) wide and 1.0 inch (25 mm) long bead of adhesive GM P/N 12346141 (Canadian P/N 10953433) or equivalent to both the right and left sides of the engine front cover to engine block junction at the oil pan sealing surfaces. gm_truck_43_ol-pn_ahsv_loc_f.gif

    gm_truck_43_ol-pn_ahsv_loc_r.gif

  2. Apply a 0.197 inch (5 mm) wide and 1.0 inch (25 mm) long bead of adhesive GM P/N 12346141 (Canadian P/N 10953433) or equivalent to both the right and left sides of the crankshaft rear oil seal housing to engine block junction at the oil pan sealing surfaces. Note: Always install a new oil pan gasket. The oil pan gasket and oil pan must be installed and the fasteners tightened while the adhesive is still wet to the touch.
  3. Install the new oil pan gasket into the groove in the oil pan. Note: The oil pan alignment must always be flush or forward no more than 0.011 inch (0.3mm) from the rear face of the engine block.
  4. Install or connect the following:
    • The oil pan onto the engine block
      1. Press the oil pan gasket into the grooves of the engine front cover and crankshaft rear oil seal housing
      2. Slide the oil pan back against a suitable straight edge
    • The oil pan bolts and nuts, but do not tighten
  5. Measure the pan-to-transmission housing clearance using a feeler gage and a straight edge. gm_truck_43_ol-pn_trnz_clrc.gif

    • Use a feeler gage to check the clearance between the oil pan-to-transmission housing measurement points
      1. If the clearance exceeds 0.011 inch 0.3mm) at any of the 3 oil pan-to-transmission housing measurement points (A), then repeat the step until the oil pan-to-transmission housing clearance is within the specification
      2. The oil pan must always be forward of the rear face of the engine block
    gm_truck_43_ol-pn_trq-sqc.gif

  6. Tighten the oil pan bolts and nuts in sequence
    • Torque to: 18 ft lb (25 Nm).
  7. Measure the clearance between the 3 oil pan-to-transmission housing measurement points in order to ensure proper alignment.
  8. Install or connect the following:
    • A new oil pan drain plug seal (O-ring) onto the oil pan drain plug
    • Oil pan drain plug into the oil pan
      1. Torque to: 18 ft lb (25 Nm)
      NOTE: The low oil level sensor is not reusable.
      gm_truck_43_ol-pn_ol-lvl-snsr.gif

    • New low oil level sensor
      1. Torque to: 115 in lb (13 Nm)
    • Transmission to oil pan bolts.
      1. Torque to: 35 ft lb (47 Nm)
    • Access plugs for the oil pan rear nuts
    • Starter wire harness bracket stud
    • Transmission oil cooler pipes (if equipped)
    • Remote oil filter pipe adapter
    • Oil filter hose clip bolt to the oil pan
    • Transmission cover and bolts.
    • Starter motor
    • Front differential assembly
    • Oil level indicator
  9. Fill the engine with oil.
  10. Connect the negative battery cable.

Dec 19, 2010 | 1997 GMC Jimmy

1 Answer

Won.t shift into grear, how do i replace the tansmission filter?


TO DO A TRANSMISSION FLUID CHANGE YOU NEED HAVE TRANSMISSION FLUID ON HAND YOU NEED TRANSMISSION FILTER AND GASKET.YOU NEED 3/8 WRENCH THE RATCHET TYPE WITH METRIC SOCKETS. YOU NEED JACK TO RAISE VECHICLE SUPPORT VECHICLE ON JACK STANDS.YOU NEED A DRAIN PAN. ONCE YOU GET VECHICLE OFF GROUND.PLACE DRAIN PAN UNDER TRANSMISSION OIL PAN REMOVE OIL PAN DRAIN BOLT.LET FLUID DRAIN OUT IN DRAIN PAN THEN SCREW DRAIN PLUG BACK IN PLACE DONT OVER TIGHTEN.REMOVE OIL PAN AND GASKET. BESURE TO HAVE PAPER TOWEL ON HAND.MAKE SURE TRANSMISSION OIL PAN GASKET SURFACE CLEAN BEFORE INSTALLING NEW PAN GASKET. ONCE TRANSMISSION OIL PAN REMOVED. REMOVE THE OLD TRANSMISSION FILTER INSTALL THE NEW FILTER.THEN WITH NEW GASKET ON OIL PAN IN PLACE.OIL PAN NEED TO BE CLEAN SO THE GASKET ADHESIVE WILL HOLD PAN GASKET IN PLACE WHILE INSTALLING PAN AND GASKET TO TRANSMISSION.INSTALL OIL PAN BOLTS INSTALL THEM CRISS CROSS TORQUE PAN BOLTS TO 7 TO 10 FT LBS. LOOK IN OWNERS MANUAL FOR TRANSMISSION FLUID CAPACITY.BUY 10 QUARTS .TO BE ON SAFE SIDE SO YOU WILL HAVE ENOUGH FLUID ON HAND. IF YOU DONT HAVE NO TRANSMISSION FLUID CAPACITY. ADD 7.5 QUARTS FLUID.WAIT FOR 2 MINUTES.CHECK TRANSMISSION FLUID LEVEL ON DIP STICK. SHOULD BE ON THE FULL MARK.CRANK VECHICLE UP.LET IDLE FEW MINUTES CHECK TRANSMISSION DIP FLUID LEVEL IF DROPPED ADD LITTLE MORE.WHILE ENGINE IDLING GETTING WARM UP. KEEP EYE ON FLUID LEVEL.WHEN FLUID LEVEL STOP DROPPING. APPLY BRAKES HOLD FOOT ON BRAKES SHIFT THROUGH ALL GEARS TWO TIMES. THEN CHECK FLUID LEVEL SHOULD BE ON FULL MARK.CHECK FOR LEAKS WHILE ENGINE RUNNING.

Nov 19, 2010 | 1996 Ford F250 Crew Cab

2 Answers

When changing the trans fluid on my 2004 Avalanche, I understand that you have to disconnect the trans lines from the radiator and run the engine until the fluid stops flowing. Is this correct? If so, do...


I didn't read about running the engine at all during the transmission fluid change. --- Removal & Installation 4L60E/4L65E To Remove:
  1. Raise and safely support the vehicle.
  2. Place a drain pan under the transmission.
  3. If equipped with a drain plug, drain the transmission fluid.
  4. If necessary, remove the bolts and position aside the range selector cable bracket for clearance while lowering the pan. It is not necessary to remove the cable from the lever or bracket.
  5. Remove the catalytic converter.
  6. Remove the oil pan bolts from the front and sides of the pan only.
  7. Loosen the rear oil pan mounting bolts about 4 turns.
  8. Lightly tap the oil pan with a rubber mallet in order to loosen the pan and allow the fluid to drain.
  9. Remove the remaining oil pan bolts.
  10. Remove the oil pan and the gasket.
  11. Remove the filter by twisting and pulling on it.
  12. Remove and discard the filter seal. The filter seal may be stuck in the pump; if necessary, carefully use pliers or another suitable tool to remove the seal.
  13. Clean the transmission and the oil pan sealing surfaces with solvent, and air dry. You must remove all traces of the old gasket material.
To Install:
  1. Coat the new filter seal with transmission fluid.
  2. Install the new filter seal into the transmission case. Tap the seal into place using a suitable size socket.
  3. Install the new filter.
  4. Install the oil pan and new gasket. Tighten the bolts alternately and evenly to 97 lb in (11 Nm).
  5. Install the catalytic converter.
  6. If previously removed, install the range selector cable bracket and bolts. Tighten the bolts to 18 lb ft (25 Nm).
  7. Apply a small amount of sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the oil pan drain plug, if equipped.
  8. Install the oil pan drain plug, if equipped. Tighten the plug to 13 lb ft (18 Nm).
  9. Lower the vehicle.
  10. Fill the transmission to the proper level with DEXRON® III transmission fluid.
  11. Check the COLD fluid level reading for initial fill only.
  12. Inspect the oil pan gasket for leaks.
4L80E/4L85E To Remove:
  1. Raise and suitably support the vehicle.
  2. Place a drain pan under the transmission oil pan. Drain the transmission fluid and install the plug. Tighten the drain plug to 13 lb ft (18 Nm).
  3. Support the transmission with a transmission jack.
  4. Remove the transmission crossmember.
  5. Disconnect the range selector cable end from the transmission range selector lever ball stud. NOTE: It is not necessary to remove the selector cable from the bracket.
  6. Remove the transmission range selector cable bracket. Reposition the bracket and cable.
  7. Remove the oil pan bolts. NOTE: The transmission oil pan gasket is reusable. Replace as needed.
  8. Remove the oil pan and gasket.
  9. Remove the magnet from the bottom of the pan, if necessary.
  10. Remove the oil filter and neck seal.
To Install:
  1. Clean the transmission and the oil pan sealing surfaces with solvent.
  2. Install the filter neck seal and filter.
  3. Install the oil pan gasket to the pan.
  4. Install the magnet into the bottom of the pan, if necessary.
  5. Install the oil pan and bolts. Tighten the oil pan bolts to 18 lb ft (24 Nm).
  6. Install the transmission range selector cable bracket. Tighten the bolts to 18 lb ft (25 Nm).
  7. Connect the range selector cable end to the transmission range selector lever ball stud.
  8. Install the transmission crossmember. Tighten the fasteners to 70 lb ft (95 Nm).
  9. Install the transmission mount nuts. Tighten the nuts to 30 lb ft (40 Nm).
  10. Remove the transmission jack.
  11. Lower the vehicle.
  12. Fill the transmission to the proper level with DEXRON® III transmission fluid.
prev.gif next.gif

Aug 26, 2010 | 2004 Chevrolet Avalanche

1 Answer

How do I change the tranny fluid in my 1998 cadillac catera


Fluid - A/T: Service and Repair
Transmission Fluid and Oil Filter Changing
REMOVAL PROCEDURE
1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
2. Place drain pan under pan
3. Remove oil pan bolts from front and sides only.
4. Loosen the rear oil pan bolts approximately four turns.
5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
6. Remove the oil pan bolts from rear oil pan and gasket.
7. Remove front oil pan bolts leaving one corner bolt in loosely.
8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
9. Remove the following remaining components:
^ The front oil pan bolts
^ The oil pan
^ The gasket
10. Remove the oil filter bolts and filter.
11. Clean the following components:
^ The transmission case
^ The front adapter case
^ The oil pan gasket surfaces with solvent
^ Air dry
^ All traces of gasket material must be removed
INSTALLATION PROCEDURE
1. Install the gasket.
2. Install the oil filter.
3. Install the bolts.
^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
NOTICE: Refer to Fastener Notice in Service Precautions.
4. Install the front oil pan.
5. Install the front oil pan gasket
6. Install the front oil pan bolts
^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
7. Install the following components:
^ Install the pan
^ Install the gasket
^ Install the bolts
^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
pan fill. Fill plug opening using and oil suction gun.
^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
9. Lower the vehicle.
10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

Sep 13, 2009 | 1998 Cadillac Catera

3 Answers

Oil Pan Gasket Replacement - How to - GMC Yukon 2000


No big job Really. Just locate your Drain Plug for the Oil. Thepan is right there, Remove the Bolts around the Pan and Remove. You will lose all of your oil so, Have something there to catch it all. Clean it all around the Edges of the Block where the Pan mounts with Degreaser and Make sure that you Scrape the Old Gasket off of Both the Block and the Pan. Run a Thin Bead of Blue ATV Silicone around the Pan Edge, Lay the Gasket on top of this Silicone. Put another Thin line on top of the Gasket and Reinstall. This Silicone is High Temp Silicone and will Seal Very Well. Make sure to put oil Back in the Motor! Please Rate my Response, I need all the Help That I can Get! Thanks!

Jan 27, 2009 | 2000 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...