Question about Cars & Trucks

Open Question

What is the torque spec on a 2002 CLK 320 Mercedes lower oil pan bolt?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

Ad
  • 158 Answers

SOURCE: 2000 sebring transmission pan torque spec

10 ft lbs no real patterm needed

Posted on Apr 03, 2009

  • 43 Answers

SOURCE: need to find battery location: 1999 Mercedes CLK 320

Hi, The battery is located in the trunk, under the trunk mat.

Posted on Apr 08, 2009

  • 1 Answer

SOURCE: mercedes clk 320 will not start

i have a 2000 clk320. it would not start sometimes, the engine would crank but it wont start. but after an hour or so it would start. sometime i'll get somewhere park, and come out an hour later and the engine would not start. if your having the same problem, take it to autoparts store ex: autozone or kragen. they could check your battery for free. and if its not the battery. than it could either be your fuel pump. or the crank position sensor. good luck. hopefully this help.

Posted on Jul 18, 2009

  • 743 Answers

SOURCE: oil and transmission pan bolt torque specs

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

Posted on Oct 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

98 jeep wrangler tj 4.0 oil pan bolt pattern or layout. An torch specs


Bobby, oil pan bolt torques for 4.0 Wrangler. Oil Pan Bolts 1/4 84 in-lbs Oil Pan Bolts 5/16 132 in-lbs As far as sequence, see last link, start in center, criss cross pattern tighten snug all, then repeat to torque spec.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Oil Pan Gasket leaking
http://jeephorizons.com/tech/99_40l_torque_specs.html
98 jeep 4 0 oil pan bolt torque sequence specs Google Search

May 21, 2016 | Jeep Cars & Trucks

1 Answer

What are the oil pan torque specs on a 1987 Pontiac Fiero GT


To install: Place a 3mm bead of RTV sealant on the oil pan sealing flange.
Install the oil pan and torque the 1 inch bolts to 6-9 ft. lbs. (8-12 Nm) and the 1.5 inch bolts to 14-22 ft. lbs. (19-29 Nm).
Install the starter assembly.
Install the flywheel and clutch housing cover.
Lower the vehicle and refill the crankcase with the specified engine oil.
Start the engine and check for oil leaks.

Mar 12, 2015 | 1987 Pontiac Fiero

1 Answer

Where can I find bolt torque specs


I suggest going to an auto parts store in your area and asking for the "HAYNES" manual for your make and model. It is an easier book to read than a "Chilton'. It will have all the torque specs you need. The book will probably cost 20 - 30 dollars. This is much less than it will cost if you torque something wrong. I would be careful trusting internet sources. It is a very worthwhile investment and a complete repair manual.

Feb 20, 2015 | Cars & Trucks

1 Answer

Need torque specs for 96 yukon 5.7 liter


Here's a link to the oil pan removal guide with pan bolt torque specs.

Jan 13, 2013 | 1996 GMC Yukon

1 Answer

WHERE IS THE OIL PLUG LOCATED ON MY 1999 MERCEDES CLK 320. I WANT TO CHANGE THE OIL AT HOME.


you will find the drain plug at bottom of oil pan, you will have to jack car up. use car stands for safety.

Feb 12, 2011 | Mercedes-Benz CLK Cars & Trucks

1 Answer

What is the oil pan bolts torque spec for a 2002 jaguar X-type V-6


Fig. Oil pan bolt torque sequence-X-Type

b8259f9.jpg



  1. Use a new oil pan gasket. Tighten the bolts, in the sequence shown, to 18 ft. lbs. (25 Nm).
  2. Tighten the pan-to-transmission bolts to 33 ft. lbs. (45 Nm).
  3. Tighten the access cover bolt to 89 inch lbs. (10 Nm).
  4. Tighten the compressor bolts to 18 ft. lbs. (25 Nm).
  5. Refill the engine with oil.
  6. Install the transfer case.
Hope this helped (rememer comment and rated this).

Apr 14, 2010 | 2002 Jaguar X-Type

2 Answers

2001 Silverado oil pan gasket is it hard to change?


it can be you must remove oil filterand housing along with oil cooler lines lower trans lines you really need a repair manual for this kind of repair for torque specs and procedures

Jul 10, 2009 | 2001 Chevrolet Silverado 2500HD

1 Answer

Need torque specs for oil pan bolts


torque specs for these bolts can be found in a Haynes or Chilton manual availiable from your local parts store, or maybe at your local library, however these bolts are usually no more than 14 ft pounds, unlike cylinder head bolts, the bolts do not need to have any stretch factor to hold the oil pan gasket in place or sealed.

May 17, 2009 | 1997 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...