Question about Nissan Cars & Trucks
Most any locksmith will have the key and can cut it to the key code for the ignition
again most have the ability to program the new key to the vehicle immobilizer
will not be cheap
Posted on Aug 09, 2017
Go to any Nissan outlet, guess they will be of help.
Posted on Aug 09, 2017
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
HI any nissan dealer should be able to get key codes for you just give them the vin number they normally charge for this but not to much ,they wil usually ask for some id and proof it's your car steve
Posted on Feb 24, 2009
Check the locking solenoid / actuator in the door behind the panel, could be burned out or loose wire. It should take about 20-30 minutes to open, fix it and close the door panel if there's no major problem. Autozone might be able to help out with a solenoid.
Posted on May 17, 2009
SOURCE: reprogramming remote and key
if its early 05 round heart shaped remote it needs programming into system at dealer with Tech2
later 05 to 07 had square (rectangle) shaped remote
1.2 ID Code Additional Registration
Note: This procedure will add additional remotes to the Keyless Entry Control Units memory. A total of 4 remote transmitters may be programmed into the Keyless Entry Control Units memory. When a total of registered and newly registered remotes exceed 4, the oldest one shall be erased.
1 Note: Make sure that all the doors are closed and unlocked. Insert the ignition key into the ignition switch.
Open the driver's side door.
2 Turn the Ignition key to the “ON” position and then to the “LOCK” position three times
(The key should remain in the “LOCK” position)
Note: This step must be carried out within five seconds.
3 “CLOSE” and “OPEN” the driver’s doors once (Leaving the driver’s door in the “OPEN” position)
Note: This step must be carried out within five seconds after step 2 is completed.
4 Wait for 8 seconds (This wait time is critical)
5 Turn the Ignition key “ON” and then to the “LOCK” position once and turn key to the “ON” position (The key should remain in the “ON” position)
OR on/lock once
Note: This step must be carried out eight seconds after step 3 is completed.
6 “CLOSE” the driver’s door
The HAZARD lights should flash 3 times (This acknowledges the Keyless Entry Control Unit has entered programming mode)
7 Operate the lock or unlock button of the transmitters to be programmed; a flash of the HAZARD lights indicates the remote has been successfully programmed into the control unit
8 The HAZARD lights will flash approx 4 seconds after pressing the remote button to indicate the Keyless Entry Control Unit has exited programming mode.
Posted on Jun 21, 2009
The key fob is the remote. But the remote type that works like a key. The remotes that you just need to carry on you to start the car or truck. That is a Key Fob.
Posted on Jul 31, 2009
i losted my nissan almera car key and i don't have the code to make a new key in my country ...it's now in lebanon exported frfom swiss
Posted on Oct 11, 2009
Tips for a great answer:
Aug 19, 2017 | Nissan Murano Cars & Trucks
Aug 09, 2017 | Nissan Cars & Trucks
Apr 07, 2017 | 2015 Nissan Murano
Apr 22, 2014 | 2007 Nissan Murano SE
Apr 07, 2013 | 2005 Nissan Murano
Dec 21, 2010 | 2007 Nissan Murano SE
Feb 08, 2010 | 2003 Nissan Murano
Jul 30, 2009 | 2005 Nissan Murano
Apr 10, 2009 | 2007 Nissan Murano SE
27 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: