Question about Cars & Trucks

1 Answer

Whom do I send the bill for removing water from my cars fuel tank.Cost $1,350,car FPV recomended fuel 98.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,504 Answers

That depends on who put the water in your car doesnt it??

Posted on Aug 09, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 17 Answers

SOURCE: 98 Buick Lesabre-fuel regulator

The nipple that will leak it on the regulator, its a device that is about a inch around and sits just forward of the intake. The other end of the hose leads up to the top of the throttle body.

Posted on Aug 20, 2008

SOURCE: fuel gage sending unit

I have a 1991 Ford F-250 with dual gas tanks. When I turn the ignition on there is no power to the fuel sending uhit. You cannot hear the unit when the key is turned on, therefore the vehicle will not start. While attempting to check for power I grabbed the frame and the I could hear the unit click on. I drove the vehicle and upon parking the vehicle I shut the ignition off and the problem occurred again. Seems to me there is a short somewhere, but what is the best solution.

Posted on Sep 22, 2008

localwonder
  • 6784 Answers

SOURCE: remove fuel pump from tank ford windstar 98

To gain access to the fuel pump, it is necessary to remove the fuel tank.

  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump module attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump module locking ring counterclockwise using a locking ring removal tool or a brass drift and remove the locking ring.
  4. Remove the fuel pump module.
  5. Remove the seal gasket and discard it.

To install:
  1. Put a light coating of grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove.
  2. Insert the fuel pump module into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  3. Install the tank in the vehicle.
  4. Install a minimum of 10 gallons of fuel and check for leaks.
  5. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF , then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi.
  6. Check for fuel leaks at the fittings.
  7. Remove the pressure gauge.
  8. Start the engine and check for fuel leaks.

Posted on May 27, 2009

  • 192 Answers

SOURCE: replacing fuel pump do i need to remove tank 1993

No, you don't have to drain the fuel tank. All you have to do is relieve the fuel pressure. If your car will start, remove the fuse or relay for the fuel pump and start the car. Let it idle until it stalls. Then turn off the key and remove the negative battery cable (to prevent sparks while you work).

I hope this helps.

Posted on Aug 18, 2009

Testimonial: "cheers mate "

  • 136 Answers

SOURCE: fuel tank sending unit needs replacing. The

the sending unit is in the tank. jack it up make sure fuels low disconnect lines and filler hose and wireing to pump drop straps lower tank.undo bolt to tank top unlock locking ring.take out sending unit and pump replace and reverse.involved but not that complicated unless your exhaust is in the way.hope that helps

Posted on Nov 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change fuel pump on a 98 Pontiac sunfire


disconnect the electrical connections and fuel lines and vent lines at the tank then disconnect the fuel filler hose from the tank. support the tank then undo the fuel tank straps then lower the tank down to the ground. be careful as the tank will be heavy depending on how much gas is in it. clean the area around the sending unit. there is a lock ring that holds the sending unit assembly in the tank that needs to be removed then you can pull out the unit. at the bottom of the sending unit is the fuel filter. follow the instructions that came with the new fuel pump.

Oct 10, 2014 | Cars & Trucks

1 Answer

Replacingn Fuel Sending Unit


If you have access to it without removing the fuel tank, there is no reason to drain the tank. Just relieve the pressure. Have rags handy when the lines are pulled apart to catch fuel drips. Clean the area well around the pump assembly to tank mounting hole. Use an air compressor if available, or just make sure no dirt falls into the tank after the pump is removed.

May 16, 2013 | Cars & Trucks

1 Answer

Fuel gauge not working


The problem is almost always caused by a defective fuel level sending unit inside the fuel tank. To replace the sending unit you must remove the gas tank from the car and replace the fuel pump module which contains the fuel level sending unit. Repair cost is about $600.00 USD's

Aug 31, 2012 | 2004 Cadillac SRX

1 Answer

We have a 98 cherokee laredo and it starts fine run for awhile then it dies like you turn the key off need help


sounds like you need to replace the fuel sending unit it is located in the fuel tank cost about $85.00 at most any auto parts store. lower fuel tank has a nut on top that looks like a washer with tabs on it use screwdriver and hammer tap in counter clockwise direction to loosen and remove. should be able to pull out fuel sending unit and replace. also replace your fuel filter at same time.

hope this helps you (PTL)

Nov 12, 2011 | Cars & Trucks

1 Answer

Where is the Fuel sensor locate on a 98 chev blazer?


Both the fuel level sensor/sending unit and the fuel tank pressure sensor are located on or in the fuel pump module.

The fuel tank will need to be lowered in order to gain access to the fuel tank pressure sensor which will be the black sensor on top of the fuel pump module.

The fuel tank will need to be removed in order to remove the fuel pump module to gain access to the fuel level sending unit attached to the side of the fuel pump module.

Nov 07, 2010 | 1998 Chevrolet Blazer

1 Answer

1990 alfa spider car will not start, looked at the fuel gauge & it seems does not move ( at zero) there's fuel in the tank. but I noticed fuel indicator light does not come on when I turn the key....


The float/sending unit inside your fuel tank has gone bad. It can be replaced, but will likely require dropping the fuel tank. The replacement itself is rather simple and straightforward, but removing and replacing the tank is messy, hazardous, and better left to a dealer or professional mechanic. You might consider using the odometer/trip meter to estimate your fuel usage.

Bill B

Aug 29, 2010 | 1990 Alfa Romeo Spider

3 Answers

Where do you find the fuel pump for a 98 oldsmobile intrigue and how do you change it.


you dont have to remove the tank, pull down your rear seats and lift up the carpet, you will see 7 nuts, remove them and you will have instant access to the fuel pump.

Apr 01, 2010 | 1998 Oldsmobile Intrigue

2 Answers

Fuel pump 98 s10


Hi:
You must first drain and lower the fuel tank, as your pump is mounted inside. With the fuel tank supported, undo the tank mounting straps, and the filler hose, then slowly lower it until you can disconnect the fuel lines and electrical harness. The pump assembly is now accessable. Remove and replace the assembly , then reinstall the tank .

Dec 21, 2009 | 1998 Chevrolet S-10 Pickup

2 Answers

Fuel gauge stopped working


Can't say for sure since you did not include year of your car but more than likely it's the fuel sending unit that requires replacement. Some years you can replace just the level sensor on the fuel sending unit but both repairs involve dropping the gas tank and opening to remove the fuel sending unit.

Aug 12, 2008 | Chevrolet Cavalier Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...