Question about Seat Cars & Trucks

1 Answer

Seat belt buzzer always on,even when buckled - Seat Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 84 Answers

Open the Seat Belt Buckle receptacle. Check for broken wires or bad switch, which is not operating when buckle is pushed in.

Posted on Aug 28, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tbock86
  • 68 Answers

SOURCE: Turn the seat belt buzzer off

Usually what I do is reroute the seatbelt behind my seat, or buckle the seat belt prior to sitting. Unless you want to rewire the sensor with a toggle switch if you have any electrical knowledge. Hope this helps.

Posted on May 09, 2009

  • 3600 Answers

SOURCE: SEAT BELT BUZZER WHERE IS IT

does it do it on the driver side? hook it up without sitting in the seat start the rig if the buzzer is on sit in the seat if it is still on you have a bad ground on the seatbelt side the short belt that it connects to. the buzzer is under the dash driver side above the sterring wheel.

Posted on May 24, 2009

  • 163 Answers

SOURCE: Seat belt won't click into buckle

make sure you are using the right one

Posted on Jan 14, 2010

  • 8404 Answers

SOURCE: seat belt buzzer stays on

The switch in your seat belt buckle is probably faulty. The simple and easy thing to do is disconnect the wire under the seat. Whether you want to do this or not is something else.

You don't say what year vehicle this is so it is difficult to give more detailed instruction.

Thanks for your question @ FixYa.com

Posted on Feb 28, 2011

  • 66 Answers

SOURCE: The driver side seat belt buzzer keeps ringing

Find and disconnect the seat belt buckle connector. short the two wires together on the harness side with a paper clip. If the chime/buzzer quits, the problem is in the buckle assembly. If the chime/buzzer is still going off, the problem is some where in the wiring or module.

Posted on Apr 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Seat belt won't buckle. What should i do?


please open the buckle assembly. Pretty sure something is stuck in it. clean all parts and reassemble.

Aug 28, 2017 | Seat Cars & Trucks

1 Answer

Seat belt sensor goes on and off as your driving with all seat belts on


Look for garbage in the drivers seat buckle.

Make sure there is no heavy weight in the passenger seat.

You likely need a seat buckle, but could be wiring.

Dec 29, 2014 | 2008 Chevrolet Uplander

1 Answer

Disable seat belt warning


It can be done using diagnostic cable and appropriate SW.
Cheep hack is to find used buckle (without the belt) and insert it into socket.

Sep 03, 2014 | 2010 Peugeot Partner Tepee

1 Answer

The driver side seat belt buzzer keeps ringing even with the belt buckled


Find and disconnect the seat belt buckle connector. short the two wires together on the harness side with a paper clip. If the chime/buzzer quits, the problem is in the buckle assembly. If the chime/buzzer is still going off, the problem is some where in the wiring or module.

Apr 17, 2011 | 2007 Dodge Dakota Cab SLT

1 Answer

Seat belt warning buzzer won't stop even when the seat belts are connected.


The seatbelt connector could be disconnected. Follow the wiring that comes out of the buckle. You would see this wire close to the cars floor/carpet. Hopefully the connector is pulled out otherwise wiring could have snapped. If the wiring looks good. You may need to clean the buckle as dirt could be preventing the switch from going off.

Feb 28, 2011 | Ford Ranger Cars & Trucks

1 Answer

Seat belt buzzer stays on even if seat belts are buckled


The switch in your seat belt buckle is probably faulty. The simple and easy thing to do is disconnect the wire under the seat. Whether you want to do this or not is something else.

You don't say what year vehicle this is so it is difficult to give more detailed instruction.

Thanks for your question @ FixYa.com

Feb 28, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

SEAT BELT BUZZER WHERE IS IT


does it do it on the driver side? hook it up without sitting in the seat start the rig if the buzzer is on sit in the seat if it is still on you have a bad ground on the seatbelt side the short belt that it connects to. the buzzer is under the dash driver side above the sterring wheel.

May 24, 2009 | 2003 Ford E150

1 Answer

Turn the seat belt buzzer off


Usually what I do is reroute the seatbelt behind my seat, or buckle the seat belt prior to sitting. Unless you want to rewire the sensor with a toggle switch if you have any electrical knowledge. Hope this helps.

May 09, 2009 | 2008 Scion Xd

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Seat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

yadayada
yadayada

Level 3 Expert

77202 Answers

Adam Truesdale

Level 2 Expert

344 Answers

Are you a Seat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...