Question about 2007 Chrysler Sebring Sedan

1 Answer

2007 sebring will not shift out of park. remove the linkage from transmission and it will shift. There is no button on shifter handle. When you apply brake you can hear a clicking sound in console by shifter but it will not come out of park.

Posted by on

  • Richard Scordino May 11, 2010

    Open up the console and find the shift lock solenoid. That's whats holding the shifter from moving.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

See if this helps. Someone on LXforums had the same problem with their300. This solution worked for me as I had the same problem as you withmy Chrylser Sebring 2007.
http://www.lxforums.com/board/showthread.php?p=1538277

Posted on Oct 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to I repair my shift gears on my Chrysler 2007 Sebring? It's stuck in park.


I assume this is a floor shift,remove shifter knob, pry the trim around the shifter up to remove to get to the 2 screws there, in the storage compartment there may be 4 screws, pull Ebrake up as far as you can then rear of console upward over ebrake handle then back,remember you have to reverse what you just did to put it back together. If your after the shift cable try to pop it off the trans first to see if it can be moved out of park at the trans if so more likely is the cable if not you may have internal trans problem.

Dec 27, 2014 | 2007 Chrysler Sebring 2.7

3 Answers

Shifting Out of Park Position


hi..

spaclear.gif A simple procedure to prevent being jammed in PARK on a grade:
  1. Do not put it in PARK until, with foot brake applied, you've secured the parking (emergency) brake.


  2. Before releasing the parking brake, apply the foot brake and move the shift lever to NEUTRAL or DRIVE.
spaclear.gif

Sep 13, 2008 | 1991 Honda Accord

2 Answers

Shifter linkage failure on 2001 Chevrolet Venture


check the linkage on the transmission, i have heard of the shift cables breaking if there is a lot of weight against the parking pin such as parking on a hill without first applying the emergency brake before placing it in park.

Aug 31, 2012 | 2001 Chevrolet Venture

1 Answer

99 E-250 will not shift into park


With the ebrake applied. Block all the wheels and disconnect the linkage at the transmission. Then see if you can move the shifter easy. if so check the transmission shift linkage. and see if it moves easy.

Dec 31, 2011 | 2002 Ford E250

1 Answer

2007 Chrysler Sebring will not shift out of park. We apply the brakes, but it still will not shift.


can you hear a slight click when applying brake?? if not interlock safty switch is bad, if so then best idea is something in shifter housing blocking it. OR cable issue

Jun 04, 2011 | 2007 Chrysler Sebring Sedan

1 Answer

How do i repair shifting cable from cosole to trans.?


Welcome to FixYa.com



REMOVAL
1. Remove air cleaner and air intake hose assembly.
2. Remove center dash trim panel.
3. Remove center console cup holder assembly.
4. Remove floor console assembly.
5. Remove console side panels.
6. Remove Transmission Control Module ftMJ bracket.
1. Remove TCM.
8. Remove shifter cable from transaxle operating lever by removing nut and clip.
9. Remove shifter cable from shifter lever assembly by removing clip.
10. Remove shifter cable from shifter lever mechanism.
11. Remove cable from firewall grommet by removing grommet assembly nuts.
12. Remove gearshift cable from vehicle.
ADJUSTMENT
Lift and rotate the gearshift hand lever into the park (F9 gate position and remove the ignition
key. This confirms the shift lever is in the gated park (F9 position.
After confirming the park gate position. turn the ignition switch . If the starter will operate. the
park gate position is correct. Move the shift lever into the neutral (NJ position. If the starter
will operate in this position, the linkage is properly adjusted. If the starter fails to operate in
either position, linkage adjustment is required.
1. Park the vehicle on level ground and set the parking brake.
2. Place the gearshift lever in park (F9 gate position and remove key.
3. Loosen the cable adjustment screw at the transaxle operating lever.
4. Pull the transaxle operating lever fully forward to the park detent position.
5. Release the park brake, then rock the vehicle to assure it is in park lock. Reset the park
brake.
6. Tighten the cable adjustment screw to 8 Nm (10 inch Ibs.J. Gearshift cable should now be
properly adjusted.
1. Check adjustment by usinq the precedinq procedure.



Thank you for Using FixYa.com

Kind Regards, Lee

Your Master Technician FixYa Expert

leedavidian_98.png

Jan 31, 2011 | 1997 Chrysler Sebring

1 Answer

Reverse is not where it belongs, it is between reverse and neutral


you may have a bent shifter rod under your car. can you pull the rubber boot up on shifter and see if it has not came loose from the shifter inside? you will need to remove the screws that hold the cover on. on the floorboard. if the problems not there,it's on the shifter linkage rod. the bushings in the shifter rods may have gone bad or have been jammed by erratic shifting,or just every day useage.that was solution for manual shift transmission.[this is solution for automatic transmission] your shifter cable may only out of adjustment,or your shifter cable may have stretched due to cold weather or just worn. open your hood, this will take 2 people to work together.one to see the transmission shift on top of transmission,the other to shift the transmission. apply the emergency brake,engine off, shift the gears back and forwards from drive to park. does it look like the cable or linkage has play or slop in it? if it does you can adjust it by putting the car in park and then tighten the bolt on top of the cable,on the top of the transmission. hope this helps and thank you for choosing fixya.com

Jan 20, 2011 | Suzuki Reno Cars & Trucks

3 Answers

My 2008 Chrysler is stick in park


emove trim ring around gear sift, turn the car on, push down on breaks, use a screwdriver to push little pink plastic piece back

Jun 03, 2010 | 2007 Chrysler Sebring Sedan

1 Answer

My 07 sebring wont shift out of park, is there anything i can do, without taking it to a dealership


look at the plastic linkage under shifter,if you hear the shift lock working.will be a pink clip that attaches to black plastic clip

May 19, 2010 | 2007 Chrysler Sebring Sedan

1 Answer

2007 GMC Sierra 2WD 4.3 litre shifter problems (automatic)


More then likely the cable from the shift lock solenoid that unlocks the shifter is binding up or the shift lock solenoid is sticking..

May 04, 2017 | 2007 GMC Sierra Classic

Not finding what you are looking for?
2007 Chrysler Sebring Sedan Logo

747 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...