Question about Ford E-350 Super Duty

2 Answers

2000 ford E350 PASENGER FRONT BRAKE STUCK UP ENGINE STOP THEN WON'T START ONLY CRUNK WON'T FIRE.

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 170 Answers

For the brakes is sounds like a seized caliper. Loosen the bleeder screw and pry the brake pads back into the caliper. Unbolt and remove it, plug the brake line with a stopper or a golf tee wrapped in electical tape. You can try to free up the caliper yourself or if it's really seized buy a rebuilt one. You need to scan the computer codes, and test for spark and fuel pressure.

Posted on Jul 27, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,615 Answers

Your discription does not make sense. If you want semi accurate help you need to give as much info as possible.

Posted on Jul 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 ford e350 cutaway


brake fluid hose towards the front wheels in the brake master is blocked.

Jun 20, 2013 | 2002 Ford E350

1 Answer

2008 ford E350 van tail lights won't turn off. It's definitely not the brake lights.


may have a defective headlight switch or a bad relay for rear lights..

Feb 10, 2013 | Cars & Trucks

1 Answer

I have a 1996 ford 350 van it has a 5.8 engine in it, My problem is when I start it ,It fires right up after a few cranks but if its in park it will idle high and then stall out or if it been running for a...


Take it to AutoZone for a free diagnostic scan. Your local Ford dealer will charge you $100+ for the same scan.

It sounds like the idle control valve and/or the mass air flow sensor. The scan will accurately pinpoint the problem.

Jun 01, 2012 | 2002 Ford E350

1 Answer

My 1998 E350 engine shuts down in 10-15 minutes when the airconditioner is switched on. The won't start immediately, even with a strong battery but it will start after a while. What could be the...


probly need a tuneup-change plug wires and distributer cap--------clean throttle body and idle control motor---------get a scan and data stream done as an option

Oct 18, 2011 | 2002 Ford E350

2 Answers

I am trying to change the plugs on 2003 E350 Ford van


you have to remove the engine shroud inside the the passenger compartment. its the cover between the 2 front seats, it covers the back 1/2 of the engine once its off you can see the entire engine almost

Mar 10, 2010 | Ford Econoline Cars & Trucks

2 Answers

Hi, My blower on my E350 1994 Ford is not working anymore... Where is it? Perhaps I can replace it myself. HELP !!!


i have a 2000 Ford E350 1 ton Van the heat works in front but blows cold air in rear. Would the problem be a blower heater switch and where is it? I hope I don't have to take off the whole dash.

Jan 28, 2010 | 2002 Ford E350

3 Answers

I need a fuse number and location or a fuse box diagram for the brake lights on a 2002 E350 super duty


go to the link bleow and follow it to the Ford web site, there you can download a free owners manual, all fuse box info u need is in the manual.

http://www.edmunds.com/ownership/howto/articles/120189/article.html

Sep 18, 2009 | 2002 Ford E350

1 Answer

Help-Ford E-350 Brake problem


First, if the recall applies to your van, it can be done anytime. There is no time limit on recalls. Call your dealer with your 17 Digit VIN number and they can check. Please rate as solved if this is what you need. thanks.

Here is the recall:

Safety Recall 92S44 - Certain 1988-1991 F250/350 Trucks for Loss of Front Brake Effectiveness
Affected Vehicles
Certain 1988-1991 F250/350 trucks over 8500 lb GVW with 7.5L EFI or 7.3L diesel (4x2 and 4x4) and 5.8L EFI (4x4 only). Trucks under 8500 lb GVW. 5.8L EFI (4x2) and F-Super Duty light trucks are not involved in this recall. Specific vehicle information is as follows:

AFFECTED VEHICLES ASSEMBLY PLANT PRODUCTION DATES F250/350 Norfolk Job#1 1988 to 4/18/91 Kansas City Job#1 1988 to 4/25/91 Ont. Truck Job#1 1988 to 5/1/91 Mich. Truck Job#1 1988 to 5/11/91 Twin Cities Job#1 1988 to 5/29/91
Reasons For Recall
In certain extremely severe driving conditions, the vehicle may experience a loss of front brake effectiveness due to overheating of brake fluid. These vehicles have a split brake system and the rear brakes remain operational. This condition has been reported primarily in vehicles operated in mountainous regions, and on vehicles that have been in service for a minimum of one to two years and where the brake fluid has absorbed moisture from the air, lowering its boiling point. It usually involves heavily loaded vehicles driving on long, steep grades, or when towing at, or near, the Maximum Gross Combination Weight Rating (GCWR) for towing. Warm weather also appears to contribute to this condition. To correct this condition, dealers will install insulators in the front brake caliper pistons on all the affected trucks. 7.5L EFI engine equipped trucks will also have insulation installed on selected portions of the front brake lines.
-----------------------------------------------------------------------------------------
PART NUMBER DESCRIPTION CLASS DEALER PRICE F2TZ-2C361-A Kit-Brake Caliper Piston Insulator (All Except 7.5L Engines) BG F2TZ-2C361-B Kit-Brake Tube Insulator Jacket (Required Only For Vehicles Equipped With 7.5L EFI Engines) Kit Also Includes Brake Caliper Piston Insulators

Brake Caliper Piston Insulator Kit
Installation Instructions
  1. Remove the front wheel and tire assemblies.
  2. Remove the brake calipers from the rotors. Refer to the appropriate shop manual for the procedures.
  3. Remove the inner and outer brake linings.
  4. Inspect the brake caliper pistons. If the pistons are phenolic, (brown in color) no modifications are required. Reassemble the calipers as described in the shop manual. If the truck is equipped with a 7.5L EFI engine, install the brake tube insulator kit. If the truck is not equipped with an 7.5L EFI engine, install the wheels and tires and release the truck.
    If the pistons are aluminum, continue as described below.
  5. Remove the steel retainer and Nomex thermal washers from the kit.
  6. Place a steel retainer on a bench with the tabs facing up. Refer to Figure 1.
  7. Place a Nomex thermal washer over the tabs so that it rests on the barb of each tab. Then, carefully press it over the barb of one of the tabs. Repeat the procedure for each of the remaining tabs.

    • NOTE:
      Do not bend the tabs. The inner edge of the washer may crease slightly as it passes over the barb. This is permissible provided that the crease can be smoothed out once the washer is in place. The washer must be installed without tearing.

  8. Push the washer down onto the back face of the retainer. Be sure it is seated uniformly on the retainer. Once installed, do not use an adhesive or other aid to hold it in place. This is neither necessary nor permissible.
  9. Snap an assembled insulator into the inside diameter of each caliper piston. Be sure the assembly is firmly seated on the rim of the piston. See Figure 2.
  10. Install the inner and outer brake linings.
  11. Clean the caliper slide surfaces on the caliper and the spindle with a wire brush and lubricate with Disc Brake Caliper Slide Grease, D7AZ-19590-A (ESA-M1C172-A) or equivalent.
  12. Reinstall the brake calipers. Refer to the appropriate shop manual for the procedures.
  13. Install the wheel and tire assemblies.

May 25, 2009 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

96 ford e350, brake pedal goes to the floor when running


Check for fluid leaks, possibly rear brake cylinders. has anything else been replaced prior to this concern?

Dec 17, 2008 | 2002 Ford E350

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...