Question about Cars & Trucks
An example... Stephanie Collins,
(because VAGUE GENERALITIES can only be
offered without your year, make & model)...
NORMALLY I would suggest:
Taking your (yet to be disclosed) year, make & model
and go onto the INTERNET... Forums & chat groups...
Whoever you are COMFORTABLE sharing your
super secret year, make & model...
(obviously not FIXYA)
Sooo... Go to the DEALER FIRST...
I personally you should go to PARTSGEEK...
to find your part.... or autozone...
and try to muscle your way through their nonsense...
Rockauto, AMAZON & eBay are way to easy
and simple... (in my personal opinion)...
If the car is a 1967 Austin Healey (BJ8) MK III, 3000...
I might suggest some entirely different PART sources...
>> ((in your search for a "TRAFFICATOR")).
RARE... BUT AVAILABLE:
"Control head assembly"
See... amazing what can be found with the
YEAR, MAKE and MODEL... (savvy... Stephanie Collins?)
Posted on Aug 02, 2017
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
The turn signal switches are known to go bad, try to use the turn signal switch and jiggle the lever after clicking to the left turn. Replace signal switch assembly.
Posted on Jul 20, 2009
Tips for a great answer:
Sep 12, 2014 | 2012 Chrysler 200 LX Sedan 2.4L 4-cyl....
Jul 14, 2011 | 1993 Dodge Dakota
Identify the blown bulb. Note that if a headlight bulb has blown, the dip beam is on the outside and the high beam is on the inside. Turn off the ignition switch and light switches.
Open the hood and replace any blown headlight bulbs. Press the plastic spring clips and remove the bulb holder from the assembly. Pull the bulb out of the bulb holder and replace it with a new bulb. It only fits one way. Be sure not to touch the bulb's glass. Replace any parking lights at the same time, they are in the headlamp unit too.
May 21, 2011 | 1995 Jaguar XJ6
Changing front, right turn signal on 2005 Buick Terraza:
Open hood; when facing the front of vehicle, the right turn signal is on the passenger
side (left). The headlight assembly
needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the
left side. Remove it. There is L-shaped pin on the right side of
the headlight assembly. Swing the pin counter-clockwise
(to the left). Pull the pin straight up
to remove. The headlight assembly is now
loose, but there is a pin snapped in a socket on the back of the assembly that
still holds the assembly. Pull the
headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held
just by the rubber gasket surrounding the assembly. You need to gently work the right side of the
gasket out of the grill cowling. The
assembly should pull straight out. The
wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and
pull out the light holder. Change the
bulb. Do not punch your man-card for
credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second
time. Once you have put the L-pin in
place, the screw back, and successfully tested the lights, you can now punch
I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.
Sep 07, 2010 | 2005 Buick Terraza
Jun 01, 2010 | 2001 Oldsmobile Silhouette
Dec 13, 2009 | 2006 Dodge Grand Caravan
Oct 29, 2009 | 2002 Dodge Caravan
Jul 19, 2009 | 1998 Chevrolet Cavalier
Jul 28, 2008 | 2000 Jeep Cherokee
23 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: