Question about 2000 Jaguar S-Type

2 Answers

How can i fix my broken drivers side window on a jag s type year 2000. the power is there but i will not go up or down all i can here is a crunching noise

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 305 Answers

Sounds like the window has come off the metal scissor runner, there is a metal fixture attatched to the bottom of the window, which has a channel groove,,,, the scissor runner has a nylon wheel at either end,which sits into the window frame groove..if these wheels come out, they cause a crunching noise..so, you need to remove door panel, and put window frame and runners together

Posted on Jul 27, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

For a X reg (2000) Jaguar S- type: to remove the rear left winder mechanism do the following... Remove the door panel: remove two Philips Screws from under the small rubber mat in the door pull recess. Starting at top outer edge lever the panel away from door using something that does not damage the paint (I used a flat wooden spatula) - you will hear the poppers as they release the panel; work down and around the panel using your fingers. At some point the bezel around the door opening handle will become loosened and you need to carefully remove it - I found this awkward. Lift the panel upwards off the door and remove the cable that goes to the switches. Next remove the large access cover made of soft material stuck on with body putty and the circular sticky plastic disc covering a hole in the lower centre of the door. Remove the loudspeaker - four bolts into door metal and a cable. Remove the trim strip from the bottom edge of the window opening. Assuming the window can be moved slide it so the securing peg can be seen through the small hole uncovered when you removbed the sticky plastic disk. It appears as two concentric circles of plastic, outside diameter about 1cm, with a hole through the middle. Knock out the middle peg with a punch of about 4mm dia. This will disappear into the door and will be needed later! Once the inner peg is removed the split outer peg can be pushed through releasing the window from the regulator mechanism. Pull the window all the way up and secure with duct tape to the side of the frame so it doesn't crash down. Remove three nuts securing the mechanism push it in to the door void and remove the electric plug. I did this through the speaker apperture and found it awkward to get out - patience is needed if yours is as difficult. Manoeuver the mechanism out through the access hole and survey the damage.

Posted on Mar 28, 2011

  • Philip Bradbury
    Philip Bradbury Mar 28, 2011

    Sorry wrong place this if for left rear door not a driver's door.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 2000 park avenue power window roll down 1/2 inch then stop?


the window regulator has a broken cable. easy and cheep to fix. remove door panel replace window regulator, you can get them on e-bay for about $30

Aug 30, 2014 | 2000 Buick Park Avenue

1 Answer

Drivers side window is like it has dropped out an i have no idea about electric windows the motor still works but heard a crunch when i was winding it up it reached the top then crunched and then proceeded...


You'd want to take it to either a mechanic or a body shop, either would be able to solve the issue.

Chances are, the regulator is broken, and there isn't really a problem w/ the motor.

Aug 19, 2010 | Ford Futura Cars & Trucks

2 Answers

2000 Dodge Dakota power window on driver side


the regulator assembly or even one of the tabs on the window that attaches to the regulator has broken. it can be a self repoair but if the glass broke then let the glass company do it.

Aug 05, 2009 | 2000 Dodge Dakota Quad Cab

1 Answer

How do i fix drivers power window? i think it's


does the window go up and down?? If not and there is a crunching type noise the regulator needs to be replaced

Jul 09, 2009 | 1996 Mercury Grand Marquis

1 Answer

Driver side power window does not move up


the cable that drives the window up and down the regulator has broken. common problem. regulator needs replaced

Jun 28, 2009 | 2000 Audi A4

2 Answers

2000 mercury mountaineer power windows won't work


check for a broken wire in the wiring between the body and door

Nov 30, 2008 | 2000 Mercury Mountaineer

1 Answer

Power window on my 2000 chevy silverado z71 won't go up


I also had the same problem on my 2000 Silverado 1500 Z71....on both doors!!! I found the best solution (even though I didn't have the money) was to get it fixed by a good mechanic who wouldn't screw up anything else in the process. Passenger side went first...then a year later, drivers side fell half way down. He researched the solution on his own...found out you have to buy the whole window motor assembly. After labor....300 bucks each window...OUCH!!! Bought my truck new in 2000. Window problem happened in 2006 then in 2007.

Sep 29, 2008 | 2000 Chevrolet Silverado 1500

1 Answer

Rear window on driver's side slides down


I've had this problem and I believe its a common problem with S types. There is a white plastic slider that wraps around a metal strut and moves up and down as the window opens and closes. The problem is that the plastic slider breaks if the car door is slammed when the window is half way down, When this occurs the slider breaks free and the wire that pulls it up and down wraps itself around the motor and jamms everything up. The fix is to replace the window regulator as a complete unit. This fairly straight forward and worth the effort as you most likely will be replacing the other regulators if you keep the car for a while. Buy the regulator either from Jag dealer or OEM part which is approx 1/2 the cost (I found mine on ebay!). Make sure your get the correct unit, left, right, front and rear are different. Take off the door panel, its all clips except you need to unscrew the two scews under the rubber insert in the door pocket first. After you have removed the panel remove the black plastic cover as well. You need to detach the glass window from the regulator, This is done by punching out the brass insert in the middle of the plastic plug that is pushed through a hole in the glass. Be careful, if you hit it too hard you can break the glass, I ended up drilling it out as this was easier. Once you have the plastic plug out the glass is detached and you can remove the regulator. This is just a few screws, the only tricky part is to get the angle right to pull it out the door frame. Installation of the regulator is just the reverse. Good luck.

Sep 07, 2008 | 2000 Jaguar S-Type

Not finding what you are looking for?
2000 Jaguar S-Type Logo

417 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...