Question about 2000 Jeep Cherokee

1 Answer

Uv joint ft end right wheel replacement instructions

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Can't really write it all out here but basics of what you need to do is to remove brake assembly, axle end nut, remove bolts that retain hub bearing from behind bearing and remove it. Axle comes through the bearing hole. If you have a control unit on axle (box with vacuum hoses going to it), that also needs to be removed. I recommend you use a complete rebuilt axle...price is not much higher than joint. Far easier to get the job done right. If you need more specific instructions, get a manual like chilton or haynes...any problems along the way, ask here!!

Posted on Jul 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove axle from front of 1998 windstar


  1. Raise and support the vehicle safely.
  2. Remove the front wheels.
  3. Insert a steel rod into the brake rotor to prevent the rotor from turning and loosen the axle wheel hub nut. Discard the nut.
  4. Remove the ball joint-to-front wheel knuckle retaining nut. Drive the bolt out of the front wheel knuckle using a punch and hammer.
  5. Remove the front brake anti-lock sensor and position it out of the way.
  6. Separate the ball joint from the front wheel knuckle using a prybar. Position the end of the prybar outside of the bushing pocket to avoid damage to the bushing.
Use care to prevent damage to the front wheel driveshaft joint boot.
  1. Remove the stabilizer bar link at the front stabilizer bar.
Make sure the CV-joint puller does not contact the transaxle shaft speed sensor. Damage to the sensor will result.
  1. Install a CV-Joint Puller (T86P-3514-A1) or equivalent between the inboard CV-joint and the transaxle case.
  2. Install a CV-Joint Extension (T86P-3514-A2) or equivalent into the puller and hand-tighten.
  3. Using an impact slide hammer, remove the driveshaft from the transaxle.
Do not allow the front wheel driveshaft and joint to hang unsupported. Damage to the front wheel driveshaft joint may result. Do not wrap wire around the front wheel driveshaft joint boot. Damage to the boot may result.
  1. Support the end of the driveshaft and joint assembly by suspending it from the chassis using a length of wire.
Never use a hammer to separate the outboard front wheel driveshaft joint from the wheel hub. Damage to the outboard front wheel driveshaft joint threads and internal components may result.
  1. Separate the outboard front wheel driveshaft joint from the wheel hub using a Front Hub Remover/Replacer (T81P-1104-C) or equivalent. Make sure the hub remover adapter is fully threaded onto the hub stud.
Do not move the vehicle without the outboard CV-joint properly installed, as damage to the bearing may occur.
  1. Remove the front wheel driveshaft and joint assembly from the vehicle.
To install:
Do not reuse the retainer circlip. A new circlip must be installed each time the inboard CV-joint stub shaft is installed into the transaxle differential.
  1. Install a new retainer circlip on the inboard CV-joint stub shaft by starting one end in the groove and working the retainer circlip over the inboard shaft housing end and into the groove. This will avoid overexpanding the circlip.
A non-metallic mallet may be used to aid in seating the retainer circlip into the differential side gear groove. If a mallet is necessary, tap only on the outboard CV-joint stub shaft.
  1. Carefully align the splines of the inboard CV-joint stub shaft housing with the splines in the differential. Exerting some force, push the inboard CV-joint stub shaft housing into the differential until the retainer circlip is felt to seat in the differential side gear. Use care to prevent damage to the inboard CV-joint stub shaft and transaxle seal.
  2. Carefully align the splines of the outboard front wheel driveshaft joint with the splines in the wheel hub, and push the shaft into the wheel hub as far as possible.
  3. Temporarily fasten the front disc brake rotor to the wheel hub with washers and two lug nuts. Insert a steel rod into the front disc brake rotor and rotate clockwise to contact the front wheel knuckle, to prevent the front disc brake rotor from turning during front wheel driveshaft and joint installation.
A new front axle wheel hub retaining nut must be installed.
  1. Manually thread the front axle wheel hub retaining nut onto the outboard CV-joint stub shaft housing as far as possible.
A new bolt and nut must be used to connect the front suspension arm to the knuckle.
  1. Connect the front suspension lower arm to the front wheel knuckle. Tighten the nut and bolt to 40-55 ft. lbs. (54-74 Nm).
  2. Install the front brake anti-lock sensor.
  3. Connect the front stabilizer bar link and tighten to 35-45 ft. lbs. (47-65 Nm).
Do not use power or impact tools to tighten the hub nut.
  1. Tighten the front axle wheel hub retaining nut to 157-212 ft. lbs. (213-287 Nm).
  2. Install the front wheels and lower the vehicle.
  3. Using the recommended type of fluid, fill the transaxle to the proper level.

Jul 07, 2014 | 1998 Ford Windstar

1 Answer

How do i replce ball joints on a 99 pontiac sufire


Lower Control Arm Ball Joint Replacement Removal Procedure Tools Required J 43828 Ball Joint Separator
  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  3. Remove the stabilizer shaft link. Refer to Stabilizer Shaft Link Replacement .
  4. Remove the wiring harness from the lower control arm.

  5. 165249.gif
    tif.gif
  6. Remove the cotter pin (1) from the ball joint (3).
  7. Remove the nut (4) from the ball joint (3).

  8. 490085.gif
    tif.gif
    Notice: Use only the recommended tools for separating the ball joint from the knuckle. Failure to use the recommended tools may cause damage to the ball joint and seal.
  9. Remove the ball joint from the steering knuckle using the J 43828 .

  10. 491742.gif
    tif.gif
  11. Remove the lower control arm front (1) and rear (4) mounting bolts.
  12. Remove the lower control arm (1) from the vehicle and place in a vice.
  13. Drill out the 3 rivets (3) retaining the ball joint to the lower control arm (2).
  14. Use a 3 mm (1/8 in) drill bit in order to make a pilot hole through the rivets.
    Finish drilling the rivets with a 13 mm (½ in) drill bit.
  15. Remove the ball joint (4) from the control arm (2).
Installation Procedure

    165250.gif
    tif.gif
  1. Install the ball joint (4) into the control arm (2).
  2. Install the 3 ball joint bolts (3) and the nuts (1). Follow the instructions in the ball joint kit. Tighten the ball joint bolts (3) according to the specifications in the instructions.

  3. 491742.gif
    tif.gif
  4. Install the lower control arm (2) to the front suspension support (1)
  5. Notice: Refer to Fastener Notice in the Preface section.
  6. Install the lower control arm front (5) and rear (4) mounting bolts.
  7. Tighten • Tighten the front bolt to 107 N·m (79 lb ft). • Tighten the rear bolt to 110 N·m (81 lb ft).
    165249.gif
    tif.gif
  8. Install the lower ball joint stud (3) to the steering knuckle (2).
  9. Install the ball joint stud (3) through the steering knuckle (2).
  10. Install the ball joint nut (4).
  11. Tighten
    Tighten the ball joint nut to 55 N·m (41 lb ft) plus 180 degree rotation minimum-65 N·m (50 lb ft) plus 180 degree rotation maximum to install the cotter pin.
  12. Install the wiring harness to the lower control arm.
  13. Install the cotter pin (1).
  14. Install the stabilizer link to the lower control arm. Refer to Stabilizer Shaft Link Replacement .
  15. Install the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  16. Inspect the front wheel alignment. Refer to Wheel Alignment Specifications in Wheel Alignment.

Sep 15, 2011 | 2003 Pontiac Sunfire

1 Answer

How do i fix front right ball joint for 2001 mazda protege lx?


SAFELY RAISE SUPPORT FRONT OF VECHICLE ON JACK STAND MAKE SURE VECHICLE PARKED ON SOLID LEVEL GROUND. REMOVE WHEEL OR TIRE. REMOVE BALL JOINT STUD PINCH BOLT AND NUT FROM THE STEERING KNUCKLE.REMOVE BALL JOINT BY PRYING IT FROM THE KNUCKLE.REMOVE BALL JOINT TO LOWER CONTROL ARM BOLT AND NUT. INSTALL NEW BALL JOINT TO LOWER CONTROL ARM.TORQUE THE BOLT TO 86 FT LBS INSTALL BALL JOINT TO THE STEERING KNUCKLE TORQUE BOLT TO 43 FT LBS YOU MORE LIKELY NEED FRONT END REALIGNMENT AFTER THE JOB DONE.

Sep 09, 2011 | Mazda Protege Cars & Trucks

1 Answer

Replacing axel on passenger side of 2000 hyundai elantra please give a step by step


  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Front wheel
    • Spindle nut
    • Wheel speed sensor, if equipped
    • Outer tie rod end
    • Stabilizer bar link
    • Lower ball joint
  3. Press the stub shaft out of the hub.
  4. Pry the inner joint out of the transaxle or intermediate shaft.

To install:

NOTE

Use new circlips, split pins and self-locking nuts for assembly.


  1. Install the inner joint so that the circlip is felt to seat in the retaining groove.
  2. Guide the stub shaft into the hub.
  3. Install or connect the following:
    • Lower ball joint and torque the nut to 43-52 ft. lbs. (58-70 Nm)
    • Stabilizer bar link
    • Outer tie rod end and torque the nut to 17-25 ft. lbs. (23-34 Nm)
    • Wheel speed sensor, if equipped
    • Spindle nut and torque the nut to 144-187 ft. lbs. (195-253 Nm)
    • Front wheel
  4. Check and/or adjust the wheel alignment.

Jun 16, 2011 | 2000 Hyundai Elantra

1 Answer

Need to replace 2003 corola front wheel bearings. need step by step instruction please


Removal & Installation To Remove:
toy_car_cor-02-04wheelhub1.gif

  1. Remove the front wheel.
  2. Remove the front axle hub nut.
  3. Disconnect the front stabilizer link from the strut.
  4. Disconnect the speed sensor (with ABS).
  5. Remove the front brake caliper and rotor.
  6. Disconnect the tie rod end.
  7. Remove mounting bolts and nut and separate the lower control arm from the ball joint.
  8. Using a plastic hammer separate the front axle shaft from the hub.
  9. Remove the 2 mounting bolts from the strut. Remove the knuckle and hub assembly.
  10. Remove the lower ball joint from the knuckle.
  11. Remove the axle hub snap ring from the knuckle. toy_car_cor-02-04wheelhub2.gif

  12. Remove the axle hub from the hub bearing using special tool 09520-00031 or equivalent hub puller.
  13. Remove the inner race from the axle hub using special tool 09950-40011 or equivalent puller.
  14. Remove the dust shield from the knuckle.
  15. Remove the axle hub bearing from the knuckle using special tool 09520-00031 or equivalent and a press.
To Install:
  1. Install the axle hub bearing on the knuckle using special tool 09950-600020 or equivalent and a press.
  2. Install the dust shield on the knuckle with 3 mounting bolts.
    • Tighten 73 in-lb (90 Nm).
  3. Install the axle hub on the knuckle using special tool 09950-600010 or equivalent and a press.
  4. Install the axle hub snap ring.
  5. Install the lower ball joint on the knuckle.
    • Tighten the ball stud castle nut 76 ft-lb (103 Nm).
  6. Install a new cotter pin.
  7. Install the knuckle on the strut with the 2 nuts and bolts.
    • Tighten 162 ft-lb (220 Nm) (except '03-'04) 113 ft-lb (153 Nm) ('03-'04).
  8. Lift the knuckle and hub assembly over the axle shaft and into the hub splines.
  9. Install the lower control arm on the lower ball joint.
  10. Connect the tie rod end to the knuckle.
  11. Connect the stabilizer link to the strut.
  12. Install the front rotor and brake caliper to the knuckle.
    • Tighten the 2 caliper bolts 79 ft-lb (107 Nm).
  13. Install the ABS sensor if equipped.
  14. Install the front axle hub lock nut.
    • Tighten 159 ft-lb (216 Nm) and stake the lock nut.
  15. Check the axle hub backlash and run-out.
  16. Install the front wheel.
  17. Check the front wheel alignment and adjust if necessary.
prev.gif next.gif

Feb 17, 2011 | Toyota Corolla Cars & Trucks

4 Answers

How do I replace the upper ball joints in my 2002 Ford Explorer?


The upper ball joints are replaceable without replacing the control arms. Use Moog K80008 ball joints and a ball joint press.

Jun 25, 2009 | 2002 Ford Explorer

1 Answer

I have a bad wheel bearing how do I replace it


Hub and Bearing Assembly
ani_caut.gif CAUTION: Do not begin this removal procedure unless the following parts are available:
  • A new front axle wheel hub retainer (3B477) (Step 1).
  • A new inboard halfshaft joint stub shaft circlip.
Once removed, these parts must not be reused during assembly. Their torque holding ability or retention capability is diminished during removal.

Removal
  1. Turn ignition switch to the OFF position and place the steering column in the unlock position.
  1. ani_caut.gif CAUTION: Discard the front axle wheel hub retainer. It is a torque prevailing design and cannot be reused. If loosened, the retainer must be removed and a new one installed.
    Remove and discard front axle wheel hub retainer (3B477).
  1. Raise vehicle on hoist.
  1. NOTE: Make sure steering column is in the unlocked position, and do not use a hammer to separate tie rod end (3A130) from the front wheel knuckle (3K185) . Use extreme care not to damage boot seal.

    Remove cotter pin from tie rod end stud and remove slotted nut. Discard cotter pin and nut.
  1. Using Tie Rod End Remover 211-001 (TOOL-3290-D) or equivalent and Tie Rod End Remover Adapter 211-087 (T81P-3504-W), remove tie rod end from front wheel knuckle.
  1. ani_caut.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to remove the nut, or bearing and seal damage will result. Loosen the nut first, then remove nut from stud using the hex hold feature.
    For SHO vehicles, remove vinyl cover from upper link stud.
    Remove stabilizer bar link (5K484) from front shock absorber (18124) .
  1. Remove disc brake caliper (2B120) and support with wire to obtain working space. Do not allow disc brake caliper to separate from the front disc brake caliper anchor plate (2B292) to prevent contamination of the disc brake guide pin journals. Do not allow disc brake caliper to hang from front brake hose (2078) . Remove front disc brake rotor (1125) . Remove front disc brake rotor from wheel hub (1104) by pulling it off the lug bolt (1107). If front disc brake rotor is difficult to remove from front wheel knuckle , strike front disc brake rotor sharply between lug bolt with a rubber or plastic hammer.
    If front disc brake rotor will not pull off, apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to inboard and outboard rotor/hub mating surfaces. Install 3-Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor by pulling on front disc brake rotor outside diameter and pushing on hub center. If excessive force is required for removal, check front disc brake rotor for lateral runout prior to installation. Refer to Section 06-00.
  1. Remove anti-lock brake sensor mounting bolt and front brake anti-lock sensor (2C204) .
  1. Remove and discard lower ball joint nut. Using Remover Adapter 211-211 (T96P-3010-A1), separate lower ball joint from front suspension lower arm (3078) .
  1. Using Rotunda Spring Compressor 014-00781 or equivalent, compress front coil spring (5310) until lower ball joint clears front suspension lower arm .
  1. Using Front Hub Remover/Replacer 204-069 (T81P-1104-C), Two Stud Adapter 205-237 (T86P-1104-A1), Metric Hub Remover Adapter 204-085 (T83P-1104-BH) and Front Hub Installer 204-067 (T81P-1104-A), press front wheel driveshaft joint (3B414) from wheel hub . Wire front wheel driveshaft joint to body to maintain a level position.


    df1570a.gif


    Item Part Number Description 1 204-085 (T83P-1104-BH) Metric Hub Remover Adapter 2 204-067 (T81P-1104-A) Front Hub Replacer 3 — Turn Wrench Counterclockwise 4 — Hold Wrench Stationary While Turning Other Wrench 5 204-069 (T81P-1104-C) Front Hub Remover/Replacer 6 204-067 (T81P-1104-A)1 Two Stud Adapter A — Make Sure Metric Hub Remover Adapter 204-085 (T83P-1104-BH) is Fully Threaded onto 1107 and is Positioned Opposite the Two Stud Adapter 205-237 (T86P-1104-A1)
  1. Remove and discard three hub and bearing retainer bolts from front wheel knuckle .
  1. NOTE: Wheel hub is not pressed into front wheel knuckle . Do not use slide hammer to remove a stuck wheel hub . Do not strike back of inner bearing race. Use of these methods will damage bearing internal parts.

    NOTE: If bearing carrier is corroded to front wheel knuckle , apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to the inboard and outboard wheel hub/knuckle mating surface and allow to soak.

    Remove wheel hub from front wheel knuckle .


    f8656a.gif

Installation
  1. NOTE: If wheel hub is damaged or if any end play is detectable, replace wheel hub . End play is not adjustable. If wheel hub is disassembled, the assembly must be replaced.

    Remove all foreign material from knuckle bearing bore for correct seating of new wheel hub.
  1. Lightly lubricate mating surfaces of bearing corner and front wheel knuckle.
  1. ani_caut.gif CAUTION: Knuckle bore must be clean enough to allow wheel hub to be completely seated by hand. Do not press or draw wheel hub into place.
    Position wheel hub in front wheel knuckle . Install three new hub and bearing retaining bolts. Tighten to 83-107 Nm (61-78 lb-ft).
  1. Push front wheel driveshaft joint into wheel hub . Hand start front wheel hub retainer.
  1. Slowly release Rotunda Spring Compressor 014-00781 or equivalent while guiding lower ball joint into front suspension lower arm .
  1. Install new lower ball joint nut. Tighten to 68-92 Nm (50-67 lb-ft).
  1. Install tie rod end into front wheel knuckle . Install new slotted nut and tighten to 47-63 Nm (35-46 lb-ft). If necessary advance nut to install a new cotter pin.
  1. ani_caut.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Install stabilizer bar link to front shock absorber . Install stabilizer bar link nut. Tighten to 77-103 Nm (57-75 lb-ft). For SHO vehicles, install stud cover.
  1. NOTE: Remove rust from the rotor and hub mating surfaces with a medium abrasive pad.

    Install front disc brake rotor and disc brake caliper . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: The front axle wheel hub retainer must be tightened to specification immediately during installation. If the retainer is not tightened immediately, the nylon lock will set incorrectly, leading to incorrect torque readings and bearing failure. Any front wheel hub retainer that is not immediately tightened to specification or is loosened must be removed and a new retainer installed.
    Install front axle wheel hub retainer . Tighten to 230-275 Nm (170-203 lb-ft).
  1. Install wheel and tire. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.

May 28, 2009 | 1999 Ford Taurus

1 Answer

Uv joint noise when turning wheel on freway at 70 mph!


is clock noise, check for gres elaking on the lf side if is leaking replace the lf side drive axel

Apr 17, 2009 | Ford Escort Cars & Trucks

1 Answer

Replacing a front wheel bearing


here is a step by step instructions on how to replace your bearing. please copy and paste the link into your browser for an image.

please do not forget to rate and comment about your experience with fixya today.

Removal & Installation
  1. Apply the brakes and hold in place.
  2. Raise the vehicle.
  3. Remove the front tire and wheel assembly.
  4. Remove the cotter pin, lock nut and spring washer from the hub nut.
  5. While the brakes are applied, loosen and remove the hub nut on the end of the driveshaft.
  6. Release the brakes.
  7. Remove the front disc brake caliper and adapter as an assembly, and the brake rotor from the steering knuckle.
  8. Remove the nut attaching the outer tie rod to the steering knuckle. To do this, hold the tie rod end stud with a wrench while loosening and removing the nut with a standard wrench or crowfoot wrench.
  9. Remove the tie rod end from the steering knuckle using Remover, Special Tool MB991113.
  10. Remove the tie rod heat shield.
  11. Remove the nut and pinch bolt clamping the ball joint stud to the steering knuckle.

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during removal. Hold the bolts stationary in the steering knuckles while removing the nuts, then tap the bolts out using a pin punch.
  12. Remove the two bolts attaching the strut to the steering knuckle.

    NOTE Use caution when separating the ball joint stud from the steering knuckle, so the ball joint seal does not get cut.
  13. Separate the ball joint stud from the steering knuckle by prying down on lower control arm and up against the ball joint boss on the steering knuckle.

    NOTE Do not allow the driveshaft to hang by the inner C/V joint; it must be supported to keep the joint from separating during this operation.
  14. Pull the steering knuckle off the driveshaft outer C/V joint splines and remove the steering knuckle.

    NOTE The cartridge type front wheel bearing used on this vehicle is not transferable to the replacement steering knuckle. If the replacement steering knuckle does not come with a wheel bearing, a new bearing must be installed in the steering knuckle. Installation of the new wheel bearing and hub must be done before installing the steering knuckle on the vehicle.
  15. If the wheel bearing and hub need removal. Do not reuse the wheel bearing.
    http://www.chiltonlibrary.com/content/images/32050/images/32050_ptcr_g0035.gif The separation of the ball joint and the knuckle
To install:
  1. Slide the hub of the steering knuckle onto the splines on the driveshaft C/V joint.
  2. Install the steering knuckle onto the ball joint stud aligning the bolt hole in the knuckle boss with the notch formed in the side of the ball joint stud.
  3. Install a new ball joint stud pinch bolt and nut. Tighten the nut to a torque of 70 ft. lbs. (95 Nm).

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during installation. Install the nuts while holding the bolts stationary in the steering knuckle.
  4. Position the lower end of the strut assembly in line with the upper end of the steering knuckle and align the mounting holes . Install the two attaching bolts. The bolts should be installed with so that the nuts face towards the front of the vehicle once installed. Install the nuts. Holding the bolts in place tighten the nuts to a torque of 40 ft. lbs. (53 Nm) plus an additional 90° turn after the specified torque is met.
  5. Place the tie rod heat shield on the steering knuckle arm so that the shield is positioned straight away from the steering gear and tie rod end once installed. Align the hole in the shield with the hole in the steering knuckle arm. Install the outer tie rod ball stud into the hole in the steering knuckle arm. Start the tie rod attaching nut onto the stud. Hold the tie rod end stud with a wrench while tightening the nut with a standard wrench or crowfoot wrench. To fully tighten the nut to specifications, use a crowfoot wrench on a torque wrench to turn the nut, and a wrench on the stud.
  6. Tighten the nut to a torque of 40 ft. lbs. (55 Nm). Install the brake rotor, disc brake caliper and adapter.
  7. Clean all foreign matter from the threads of the driveshaft outer C/V joint. Install the hub nut in the end of the driveshaft and snug it.
  8. Have a helper apply the brakes. With vehicle brakes applied to keep brake rotor and hub from turning, tighten the hub nut to a torque of 180 ft. lbs. (244 Nm)
  9. Install the spring washer, lock nut and cotter pin on the hub nut. Wrap the cotter pin ends tightly around the lock nut.
  10. Install the tire and wheel assembly. Install the wheel mounting nuts and tighten them to a torque of 100 ft. lbs. (135 Nm).
  11. Lower the vehicle.
  12. Set the front toe on the vehicle to required specification.

Apr 17, 2009 | 2003 Chrysler PT Cruiser

1 Answer

Cannot remove the front drive shaft


you have to remove the differential cover this will exp[ose the carfrier gear. you have to remove the end bearing caps make sure you keep them in order they have to be replaced the same way . there is a retaining ring on each axle that must be removed before you can remove the axle. remember wwhen you assemble it back that you replace those rings on the axles. please rate this........thanks

Sep 23, 2008 | 1997 GMC Jimmy

Not finding what you are looking for?
2000 Jeep Cherokee Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...