Question about 1994 Ford F150 Styleside Supercab

2 Answers

What is the name of the bracket the spring sits in on 1994 f150 4x4 single shock frnt end bolts to the frame

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 195 Answers

If it's the part on the upper end of the coilspring, and it is a coilover suspension in front (meaning the shock absorber is mounted in the middle of the coilspring) then it is a called the shock top plate, and if it is a model where the shock absorver and coilspring are mounted one beside the other, then the bracket is called simply the spring seat. Although in both cases you can just ask for a spring seat for the front suspension and they will give you the right part and will know what you're talking about. If it is the part on the lower end of the coilspring, then it is called the control arm and is usually a one piece unit consisting of the control arm itself, the ball joints and the mount bushings.

Posted on Jul 28, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 103 Answers

Lower control arm.

Posted on Jul 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steps to replace 2007 dodge dakota tront shocks from strut spring assembly


Hello Russell,

If you replacing the front struts as an assembly the springs will be equipped and ready to install.

If your purchasing the strut assembly without the coil springs you will need a spring compressor.

  1. Before servicing the vehicle a service manual for safety precautions should be consulted.
  2. Raise and support the vehicle.
  3. Remove the tire and wheel assembly.
  4. Support the lower control arm outboard end.
  5. Remove the upper shock nuts.
  6. Remove the stabilizer link lower nut and then separate the stabilizer link from the lower control arm to gain access to the lower shock bolt.
  7. Remove the lower shock bolt.
  8. Remove the shock.
To install:
  1. Install the upper part of the shock into the frame bracket.
  2. Install the nuts. Tighten to 45 ft. lbs. (61 Nm).
  3. Install the lower part of the shock into the lower control arm. Tighten the bolt to 155 ft. lbs. (210 Nm).
  4. Install the stabilizer link lower nut to the lower control arm.
  5. Remove the support from the lower control arm outboard end.
  6. Install the tire and wheel assembly.
  7. Remove the support and lower the vehicle.

Jul 27, 2016 | Dodge Cars & Trucks

1 Answer

My 2003 oldsmobile bravada back end sits very low. Its either my strut or shocks.My question is, for this model, are the rear shocks coil or air springs?


The shocks do not set ride Hightower. The leaf springs set ride hieght in the rear. So ether the leaf springs are worn out or the shackles that hold the springs to the frame are broken (should be very obvious if they are). Most likely the rear leaf springs are the problem.

Aug 07, 2011 | Oldsmobile Bravada Cars & Trucks

1 Answer

My Front left tire is tilted inward and underneath the truck i found one of the support bars that run's across is broken off on the left side. I looked around the wheel and found that no metal was bent so...


General Description
The front suspension allows each wheel to compensate for changes in the road surface without affecting the opposite wheel. Each wheel independently connects to the frame with a steering knuckle, ball joint assemblies, and upper and lower control arms.
The control arms specifically allow the steering knuckles to move in a three-dimensional arc. Two tie rods connect to steering arms on the knuckles and an intermediate rod. These operate the front wheels.
The two-wheel drive vehicles have coil chassis springs. These springs are mounted between the spring housings on the frame and the lower control arms. Double, direct acting shock absorbers are inside the coil springs. The coil springs attach to the lower control arms and offer ride control.
The upper part of each shock absorber extends through the upper control arm frame bracket. This bracket has two grommets, two grommet retainers, and a nut.
A spring stabilizer shaft controls the side roll of the front suspension. This shaft is mounted in rubber bushings that are held by brackets to the frame side rails. The ends of the stabilizer shaft connect to the lower control arms with link bolts. Rubber grommets isolate these link bolts. Rubber bushings attach the upper control arm to a cross shaft. Frame brackets bolt the cross shaft.
A ball joint assembly is riveted to the outer end of the upper control arm. A rubber spring in the control arm assures that the ball seats properly in the socket. A castellated nut and a cotter pin join the steering knuckle to the upper ball joint.
The inner ends of the lower control arm have pressed-in bushings. The bolts pass through the bushings and join the arm to the frame. The lower ball joint assembly is a press fit in the lower control arm and attaches to the steering knuckle with a castellated nut and a cotter pin.
Ball socket assemblies have rubber grease seals. These seals prevent entry of moisture and dirt and damage to the bearing surfaces.
Four-wheel drive models have a front suspension that consists of the control arms, a stabilizer bar, a shock absorber, and right and left torsion bars. The torsion bars replace the conventional coil springs. The lower control arm attaches to the front end of the torsion bar. The rear end of the torsion bar mounts on an adjustable arm at the crossmember. This arm adjustment controls the vehicle trim height.
Two-wheel drive vehicles have tapered roller sheel bearings. These bearings are adjustible and need lubrication.
Four-wheel drive models and RWD Utilities have sealed front-wheel bearings. These bearings are pre-adjusted and need no lubrication.
Heat treatment may create darkened areas on the bearing assembly. This discoloration does not signal a need for replacement.
Hope this helps?

Jun 27, 2017 | 1999 Chevrolet S-10 Pickup

1 Answer

How to change 2007 dodge 1500 front struts?


Removal & Installation Independent Front Suspension – 2WD Vehicles To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Safely raise and support the vehicle.
  3. Support the lower control arm outboard end.
  4. Remove or disconnect the following:
    • Upper shock absorber nut, retainer and grommet
    • Lower nuts and shock absorber
To Install:
  1. Install or connect the following:
    • Lower retainer and grommet on the shock absorber stud and insert shock absorber through frame bracket hole
    • Lower nuts
      1. Torque to: 25 ft. lbs. (34 Nm)
    • Upper grommet, retainer and new nut (or existing nut with Mopar Lock N Seal or Loctiti 242) on the shock absorber stud
      1. Torque to: 40 ft. lbs. (54 Nm)
  2. Remove support from lower control arm outboard end.
  3. Lower the vehicle.
Independent Front Suspension – 4WD Vehicles To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Safely raise and support the vehicle.
  3. Remove tire and wheel assembly.
  4. Support the lower control arm outboard end.
  5. Remove or disconnect the following: dod_ram15_02-04_4wd_shock.gif

    • Upper shock nut with insulator and retainer
    • Lower shock bolt
    • Shock absorber
To Install:
  1. Install or connect the following:
    • Upper part of shock absorber into frame bracket with insulators and retainers and nut
      1. Torque to: 40 ft. lbs. (54 Nm)
    • Lower part of shock absorber into lower control arm with the bolt
      1. Torque to: 100 ft. lbs. (135 Nm)
  2. Remove support from lower control arm.
  3. Install tire and wheel assembly.
  4. Lower the vehicle.
Link/Coil Front Suspension To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Nut, retainer, and grommet from upper stud in engine compartment dod_ram15_02-04_shock.gif

    • Nuts from upper shock bracket
  3. Lower bolt from axle bracket and shock absorber from engine compartment
To Install:
  1. Position lower retainer and grommet on upper stud and insert the shock through the spring from the engine compartment.
  2. Install or connect the following:
    • Lower bolt
      1. Torque to: 100 ft. lbs. (135 Nm)
    • Upper shock bracket and nuts
      1. Torque to: 55 ft. lbs. (75 Nm)
    • Upper grommet, retainer and upper shock absorber nut
      1. Torque to: 35 ft. lbs. (47 Nm)
prev.gif next.gif

Jul 22, 2010 | 2007 Dodge Ram Truck

1 Answer

How to replace front shock bsorbers


This is for the 2WD model:

2-Wheel Drive
  1. Raise and support the front of the vehicle safely using jack stands.
  2. Using an open end wrench, hold the shock absorber upper stem to prevent it from turning, then remove the upper stem retaining nut, the retainer and rubber grommet.
c16056c.gif
Common front shock absorber mounting-2WD vehicles

  1. Remove the shock absorber-to-lower control arm retaining bolts and lower the shock absorber assembly from the bottom of the control arm.
  2. Inspect and test the shock absorber; replace it, if necessary.
To install:
  1. Fully extend the shock absorber stem, then push it up through the lower control arm and spring so that the upper stem passes through the mounting hole in the upper control arm frame bracket.
  2. Install the upper shock absorber nut and tighten to 100 inch. lbs. (11 Nm) on 1994 models 145 inch lbs. (16 Nm) on 1995 models, 54 ft. lbs. (73 Nm) on 1996 models, or 106 inch lbs. (12 Nm) on 1997-99 models while holding the stem with an open end wrench. Be careful not to crush the rubber bushing.
  3. Install the shock absorber-to-lower control arm retaining bolts and tighten to 20 ft. lbs. (27 Nm) on 1994-95 models and 54 ft. lbs. (73 Nm) on 1996 models, or 22 ft. lbs. (30 Nm) on 1997-99 models.
  4. Remove the jack stands and carefully lower the vehicle.

Nov 01, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

I have a 94 jeep wrangler front left axle seal bad. I took the left side apart and not sure how to get the seal back in. Do I need to open the inspection cover on the diff. and take the gears out?



Rear Axle Notes
  1. Raise and support vehicle.
  2. Remove rear wheels.
  3. Scribe alignment marks on propeller shaft and axle for proper assembly, then disconnect propeller shaft from axle.
  4. Disconnect the track bar from axle mounting bracket.
  5. Disconnect parking brake cable at equalizer.
  6. Disconnect shock absorbers at axle tubes.
  7. Disconnect hydraulic brake hose at rear axle Tee-fitting, then tape ends of hose and fitting to prevent contamination.
  8. Disconnect axle vent tube from axle.
  9. Remove U-bolts and tie plates.
  10. Loosen spring mounting bolts.
  11. If equipped, disconnect ABS wiring connections at axle.
  12. Support axle with suitable jack.
  13. Remove spring-to-shackle attaching bolts and lower spring to the floor.
  14. Remove axle assembly.
  15. Reverse procedure to install.

Front Axle Notes
  1. Raise and support vehicle at frame behind front springs.
  2. Remove front wheels.
  3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
  4. Disconnect connecting rod at steering knuckles.
  5. Disconnect shock absorbers at axle housing.
  6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
  7. Disconnect breather tube at axle housing.
  8. Disconnect stabilizer bar link bolts at spring clips.
  9. Remove disc brake calipers, rotors and brake shields.
  10. Remove U-bolts and tie plates.
  11. Support axle assembly with suitable jack to relieve spring tension.
  12. Loosen rear spring shackle to spring attaching bolts.
  13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
  14. Remove axle from under vehicle.
  15. Reverse procedure to install.

Jul 21, 2009 | 1994 Jeep Wrangler

1 Answer

I need to know how to get to the rear suspension (tower)


i don't think you have to do any repairs from the top end. I will list most fromFord shop manual. Please rate as Fixya if this answers your questions. Please report back. Good luck.

Section 04-02: Suspension and Wheel Hubs, Rear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual
REMOVAL AND INSTALLATION Spring Rear
Removal
  1. Position a hoist under the rear axle housing, and raise the vehicle. Refer to Section 00-02 . Place jackstands under frame side rails.
  1. Remove rear stabilizer bar as outlined.
  1. Disconnect the lower studs of the two shock absorbers from the mounting brackets on the rear axle assembly .
  1. Unsnap the RH parking brake rear cable and conduit (2A635) from RH upper arm retainer before lowering the rear axle assembly .
  1. Lower the hoist and axle housing until the rear springs are released.
  1. Remove rear spring and rear spring center mounting insulators (5741) from vehicle.
    -----------------------------------------------------------------
Shock Absorber Removal
Raise the vehicle on a hoist. 1. To assist in removing the upper attachment on shock absorbers using a plastic dust tube, place an open end wrench on the hex stamped into the dust tube's metal cap. For shock absorbers with a steel dust tube, simply grasp the tube to prevent stud rotation when loosening the retaining nut.
  1. Remove the shock absorber retaining nut, washer, and insulator assembly from the stud on the upper side of the frame. Discard nut. Compress the shock absorber to clear the hole in the frame, and remove the inner insulator and washer from the upper retaining stud.
  2. Remove the self-locking retaining nut, and disconnect the shock absorber lower stud from the mounting bracket on the rear axle tube.
  3. Perform Shock Absorber Checks. Refer to Section 04-00 to determine shock absorbers performance.
Installation
  1. Properly prime the new shock absorber . Refer to Section 04-00 , Shock Absorber Checks.
  1. Place the inner washer and rear spring insulator (5536) on the upper retaining stud, and position the shock absorber so that the upper retaining stud enters the hole in the frame. While holding the shock absorber in this position, install a new rear spring insulator , washer and nut assembly on the upper side of the upper frame. Be sure to seat the rear spring insulator in the frame attaching hole. Tighten nut to 34-46 Nm (25-34 lb-ft).
  1. Extend the shock absorber , and place the lower stud in the mounting bracket hole on the rear axle assembly housing. Install a new self-locking retaining nut. Tighten nut to 76.5-103.5 Nm (56-76 lb-ft).
  1. Lower vehicle.
-----------------------------------------------------------------------------
Arm Lower
Removal
Refer to the illustration in Description and Operation. NOTE: To improve rear axle assembly noise and vibration concerns, the rear suspension should be fastened to the frame and rear axle assembly at the curb height position.
NOTE: If one rear suspension lower arm requires replacement, also replace the opposite rear suspension lower arm .
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN REAR SUSPENSION LEVELER COMPRESSOR SWITCH OFF (IF SO EQUIPPED).
NOTE: If both rear suspension arm and bushings and both rear suspension lower arms are to be removed at the same time, remove both rear springs as outlined under Rear Spring Removal. For air spring removal, refer to Section 04-05 .
  1. Mark rear suspension shock absorber relative to protective sleeve with the vehicle in a static, level ground condition.
  1. Remove rear stabilizer bar as outlined.
  1. Raise the vehicle on a hoist, and place jackstands under the rear axle assembly . Refer to Section 00-02 .
  1. Lower the hoist until the shock absorbers are fully extended to relieve rear spring pressure.
  1. Support rear axle assembly under differential pinion nose as well as under rear axle assembly .
  1. Remove and discard the lower arm pivot bolt and nut from the axle bracket. Then, disengage the rear suspension lower arm from the bracket.
  1. Remove and discard the pivot bolt and nut from the frame bracket, and remove the rear suspension lower arm .
-----------------------------------------------------------------
Upper
Removal
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Suspension Bushing Service Set T79P-5638-A1, A2 and A5 Rear Axle Control Arm Bushing Tools T86P-5638-AH
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
  1. Raise the vehicle, and support the frame side rails with jackstands. Refer to Section 00-02 .
  2. Support the rear axle assembly .
  3. Lower the rear axle assembly , and support the rear axle assembly under differential pinion nose as well as under rear axle assembly .
  4. Unsnap parking brake rear cable and conduit from upper arm retainer.
  5. Remove and discard the nut and bolt retaining the rear suspension arm and bushing to the rear axle assembly housing. Disconnect the rear suspension arm and bushing from the housing.
  6. Remove and discard the nut and bolt that secures the rear suspension arm and bushing to the frame bracket, and remove the rear suspension arm and bushing . If upper arm rear bushing is to be replaced, use Suspension Bushing Service Set T79P-5638-A and Rear Axle Control Arm Bushing Tools T86P-5638-AH and the following procedure:
  7. Place the upper arm rear bushing remover tool in position, and pull bushing out. Using Suspension Bushing Service Set T79P-5638-A install bushing assembly into bushing ear of rear axle assembly.
------------------------------------------------
Stabilizer Bar
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
Removal
  1. Raise vehicle on hoist, and place jackstands under the frame side rails. Refer to Section 00-02 .
  1. Lower the hoist and rear axle assembly housing until the shock absorbers are fully extended.
  1. Disconnect rear stabilizer bars from rear stabilizer bar link and bushing (5C488) . Remove bolts and stabilizer bar bracket (5486) retaining rear stabilizer bar to rear axle assembly .

Mar 05, 2009 | 1994 Lincoln Town Car

2 Answers

Diagram of front end for '94 F150 Ford


this is a 96 f150 suspension, 4x2, not 4x4.

f7f2b45.gif
Item Part Number Description 1 N806246-S56 Nut and Washer 2 5A333 Retainer 3 18124 Front Shock Absorber 4 40949 Bolt 5 N62048 Nut 6 N806496 Nut 7 18126 Lower Shock Bracket 8 805033 Bolt 9 3B404 Caster and Camber Adjuster 10 800937 Nut 11 5414 Front Spring Insulator 12 3105 Front Wheel Spindle (RH) 13 3106 Front Wheel Spindle (LH) 14 3050 Front Suspension Lower Arm Ball Joint 15 3B008 Steering Arm and Drag Link 16 800895 Nut 17 642569 Cotter Pin 18 383489 Nut 19 3006 Front Axle 20 388727 Bolt (F-150) 21 389574 Bolt (F-250, F-350) 22 606085 Bolt 23 605920 Bolt 24 3405 Radius Arm 25 34992 Nut 26 5A307 Lower Spring Seat 27 5414 Front Spring Insulator 28 18183 Front Shock Absorber Mounting Bracket 29 34992 Nut 30 5310 Front Coil Spring 31 5B315 Upper Spring Seat 32 18198 Insulator A — Tighten to 34-48 Nm
(25-35 Lb-Ft) B — Tighten to 18-23 Nm
(13-18 Lb-Ft) C — Tighten to 32-58 Nm
(23-42 Lb-Ft) D — Tighten to 60-80 Nm
(44-59 Lb-Ft) E — Tighten to 68-92 Nm
(50-67 Lb-Ft) F — Tighten to 112-152 Nm (83-112 Lb-Ft) G — Tighten to 112-152 Nm (83-112 Lb-Ft) H — Tighten to 340-460 Nm (250-339 Lb-Ft)

Jan 29, 2009 | 1994 Ford F150 Styleside Supercab

Not finding what you are looking for?
1994 Ford F150 Styleside Supercab Logo

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...