Question about Hyundai Motor 2003 Elantra

1 Answer

How do you get the top of the bearings out - Hyundai Motor 2003 Elantra

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Main ones?????or what???????

Posted on Jul 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can the connecting rod bearings be changed via the oil pan without pulling the engine?


Yes
however as there may/will be a ring ridge at the top of the cylinder any new bearings fitted may make the top ring hit that ridge
if you are replacing just oneset of bearings on one con-rod you may get away with it but it there is a tapping noise after the job it will be the rings hitting the ridge
if left un-attended to , there is the possibilities of broken top rings or broken ring lands on the piston

Nov 19, 2015 | Cars & Trucks

1 Answer

Crankshaft rod bearings


NO , YOU NEED A NEW CRANKSHAFT AND MAIN BEARINGS AND ROD BEARINGS

Nov 15, 2013 | Honda Civic Cars & Trucks

1 Answer

How do you know when the front bearings are worn out on a 2000 ford mustang and does the bearing come separately from the hub when u replace it?


If you jack up the car, grab the wheel at the top and the bottom and see if there is any play while trying to pull the top of the tire towards and away from you. The bearing comes on the hub and has the ABS ring mounted to it also.drsinister69_0.jpg

Nov 05, 2010 | 2000 Ford Mustang

1 Answer

2001 ford explorer packing front bearings


This is going to sound silly. Buy a bearing packer. This device is not expensive and should be available at just about any auto parts store.

It is a fairly simple device. It looks like two shallow cones mounted on a shaft. The bottom cone is fixed and the top cone unscrews from off the shaft. The shaft itself is hollow with a grease fitting on top. Just remove the top cone, place the bearing on the bottom cone and screw on the top cone firmly, but not over-tight. Attach a grease gun loaded with the desired grease and pump the handle until you see grease come out the sides. At that point, the bearing should be fully packed.

Jul 22, 2010 | 2001 Ford Explorer

1 Answer

Noise from front wheel while driving whinning turn steering slightly to left stops , if bearing can i do my self transit 280 ,53 plate


Sounds like the bearing is loose, yes you can do it yourself. Remove the bearing dust cap, do you see a cotter pin, if so jack up the front wheel, remove the cotter pin and locking ring, then place your hand just at the bottom of the bearing, using your other hand gently tap the top of the tire, the bearing should come out, inspect it to make sure it is okay and not in need of replacement, repack the bearing with new bearing grease and reinstall it. Ajust the bearing to 0 play, do this by tightening the bearing nut, and grab the tire at the top with one hand and bottom with the other, then push and pull in opposite directions at the same time, if the tire wobbles then tighten the bearing a little more until the tire will not wobble. Spin the tire around forwards and then backwards serveral time and check for 0 play again. After spinning and 0 play is good, reinstall the nut locking device and cotter pin, and dust cover. Hope this helps, let me know.

Jul 01, 2010 | 1981 Ford F 100

1 Answer

Abs light come on and 4wd light flashes


check your front wheel bearings by jacking up the front end of your vehicle and trying to wiggle the tire at the top and bottom of the tire. If the tire seems to be jiggling a little bit at the hub; not the suspension or steering, your wheel bearing needs to be replaced. If it gets really bad you can actually see the wheel inverted or the top of the tire leaning towards the inside from the front of the vehicle.

when your wheel bearings go the sensor in the bearing goes off and the abs light comes on.

Good Luck

Apr 08, 2010 | 2005 Ford Escape

1 Answer

Ford f150 how do I replace the front wheel bearings? parts?


First check if there is a screw in the outer side of the axle on trucks there is usually an adjusting screw to tighten the bearing. be carefull not to over tighten

Aug 05, 2009 | 1997 Ford F150 Regular Cab

2 Answers

The left hand wiggle part two.


Top to bottom and side to side. There should not be any slack in the bearings.

Jul 19, 2009 | 2001 Ford Focus

1 Answer

Left-front wheel bearing is worn-out


the wheel bearing will need to be pressed on so unless you know someone to press it for you you might want to take it to a shop.

Mar 14, 2009 | 1995 Mitsubishi Galant

Not finding what you are looking for?
Hyundai Motor 2003 Elantra Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...