Question about 2006 Honda Odyssey

3 Answers

How do I align low beam headlight in 2006 honda odyssey .Right side headlamp set to low will not light up signs on side of road(Stop,yield)

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 04, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,776 Answers

There should be a headlight adjustment screw located above and to the side of the light behind the headlight retainer ring. Hope this helped.

Posted on Jul 27, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 298 Answers

1-be careful with head light because they get very hot 2- park your car in a level surface 3- get some one who weight the same as you to sit in the drivers seat 4-clean the lens on both lamps 5-be sure to park facing a wall at lease 25 ft. away from the wall 6- measure the height of the lamp on your vehicle from the floor to the top of the lamp 7- then go to the wall and use the same height. some of these vehicle are equipped with a leveler on the lamp if so use the leveler and take the bubble to the middle I hope this information is of use good luck

Posted on Jul 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust my headlights on my 2001 Honda Odyssey ? The low beams are too low.


open the hood, and look at the top of the light , you should see a screw head, that would be your up and down adjustment,, there is one on the side of the unit for left to right adjustments

Sep 27, 2011 | 2001 Honda Odyssey

1 Answer

How do remove a headlight from the the assembly for a 1999 buick park avenue


Hello there,
For you to be able to take off the assembly of the headlight on your car, please follow the steps below:
Ensure that the headlight switch (on the driver side of the Regal's passenger cabin) is in the off position.
Release the hood latch and open the hood.
Approach the passenger-side headlamp assembly. (Although on your left, this is the right-side lens assembly when sitting inside the vehicle.)
Locate the two white retaining brackets on the top rear edge of the assembly.
Lift the tabs straight upward about an inch to an inch and a half.
Grab the assembly from the sides of the front edge (being careful of any broken lens pieces; although the lens is made of plastic, you can still get cut by jagged pieces).
Firmly pull the assembly outward, away from the front of the Regal. Wiggle the assembly slightly to unseat the headlamp assembly alignment guide pins from their anchors.
Pull the assembly out only far enough to access the wire harness connections of the low-beam headlight, the high-beam headlight and the integrated parking/directional light.
Twist the retaining collar of the low-beam lamp (the outside lamp, toward the fender) a quarter-turn counterclockwise to remove the light from the headlamp assembly while it is still attached to the wire harness. Be careful not to contact the halogen bulbs with your bare hands, or you can damage the bulbs.
Twist the retaining collar of the high-beam headlight (the inner headlight, closer to the grill) in the same manner as you did the low-beam lamp to remove the high-beam bulb and harness from the headlamp assembly.
Twist the socket of the last remaining integrated parking/directional bulb and wire harness assembly a quarter-turn counterclockwise to remove it from the headlight assembly.
Discard the assembly and replace it with the new headlamp assembly by following the steps above in reverse order. Make sure to align the tabs of the retaining collar and parking/directional lamp socket with the mating notches on the new headlamp assembly before turning them all clockwise a quarter-turn to lock them in place.
All the best Elect_Comp

Sep 13, 2011 | Buick Park Avenue Cars & Trucks

1 Answer

How do you align or focus headlights beams that are to


AIMING THE HEADLIGHTS

The headlights must be properly aimed to provide the best, safest road illumination. The lights should be checked for proper aim and adjusted as necessary. Certain state and local authorities have requirements for headlight aiming; these should be checked before adjustment is made.

CAUTION About once a year, when the headlights are replaced or any time front end work is performed on your vehicle, the headlight should be accurately aimed by a reputable repair shop using the proper equipment. Headlights not properly aimed can make it virtually impossible to see and may blind other drivers on the road, possibly causing an accident. Note that the following procedure is a temporary fix, until you can take your vehicle to a repair shop for a proper adjustment.
Headlight adjustment may be temporarily made using a wall, as described below, or on the rear of another vehicle. When adjusted, the lights should not glare in oncoming car or truck windshields, nor should they illuminate the passenger compartment of vehicles driving in front of you. These adjustments are rough and should always be fine-tuned by a repair shop which is equipped with headlight aiming tools. Improper adjustments may be both dangerous and illegal.
For most of the vehicles covered by this guide, horizontal and vertical aiming of each sealed beam unit is provided by two adjusting screws which move the retaining ring and adjusting plate against the tension of a coil spring. There is no adjustment for focus; this is done during headlight manufacturing.
Because the composite headlight assembly is bolted into position, no adjustment should be necessary or possible. Some applications, however, may be bolted to an adjuster plate or may be retained by adjusting screws. If so, follow this procedure when adjusting the lights, BUT always have the adjustment checked by a reputable shop.
Before removing the headlight bulb or disturbing the headlamp in any way, note the current settings in order to ease headlight adjustment upon reassembly. If the high or low beam setting of the old lamp still works, this can be done using the wall of a garage or a building:
  1. Park the vehicle on a level surface, with the fuel tank about 1 / 2 full and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall.

fbcb5a7.jpg

Fig. : Location of the aiming screws on most vehicles with sealed beam headlights


97dee4f.jpg

Fig. : Dual headlight adjustment screw locations-one side shown here (other side should be mirror image)

9a545e8.jpg

Fig. : Example of headlight adjustment screw location for composite headlamps
  1. If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows.
  2. Turn the headlights ON and mark the wall at the center of each light's low beam, then switch on the brights and mark the center of each light's high beam. A short length of masking tape which is visible from the front of the vehicle may be used. Although marking all four positions is advisable, marking one position from each light should be sufficient.

031bc2f.jpg

Fig. : Low-beam headlight pattern alignment

758eed8.jpg

Fig. : High-beam headlight pattern alignment

  1. If neither beam on one side is working, and if another like-sized vehicle is available, park the second one in the exact spot where the vehicle was and mark the beams using the same-side light. Then switch the vehicles so the one to be aimed is back in the original spot. It must be parked no closer to or farther away from the wall than the second vehicle.
  2. Perform any necessary repairs, but make sure the vehicle is not moved, or is returned to the exact spot from which the lights were marked. Turn the headlights ON and adjust the beams to match the marks on the wall.
  3. Have the headlight adjustment checked as soon as possible by a reputable repair shop.

Hope helped with this information. Good luck (remember rated this help).

Nov 10, 2009 | 1996 Toyota Camry

3 Answers

WHAT ARE THE SPECS TO ALIGN Headlights for 2006 chevy colorado


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 06, 2009 | 2006 Chevrolet Colorado

1 Answer

The 2006 RL headslights are horrible. On low beam there is like a curtain that comes down and you can only barely see the road, and you cannot see anything above the hood of the car! Many people have...


2006 RL headlamps are similar to 2005 TL headlamps. We owned a 2005 TL (great car). The headlamps are HID (high intensity discharge) and many people don't like the sharp cutoff that they have. Your only option other than driving with the high beams on is to have them professionally re-aimed. This may or may not help the problem. Take it to your Acura dealer and talk to the service department about this.

Sorry, I wish there was any easy fix.

Bob

Oct 27, 2009 | 2006 Acura RL

2 Answers

How do you adjust the headlights on a 2006 dodge ram 2500 ?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jul 28, 2009 | Dodge Ram 2500 Cars & Trucks

2 Answers

Toyota avensis 2002 1798cc, headlights beam is low need to raise


you need to bring it to a garage with a headlight alignment machine to pass an MOT. ensure the headlight position switch (on the right hand side of the dash) is set to "0"

Mar 22, 2009 | 2002 Toyota Camry

1 Answer

How do you adjust the headlight of a 2005 Honda Odyssey?


I assume you are talking about a vertical adjustment.

If so Easy enough. Park the car about 25 feet from a wall or so. This is normal range for adjustment. Turn on your low beams.

Now Pop the hood and take a look at your headlight On You will see a black rubber bump stop. This is used to adjust your hood height.

Right behind that you will see a area where you can insert a screw driver into. Turn that with the screw driver and the headlight vertical angle will change

Here is a picture
[IMG]http://i67.photobucket.com/albums/h298/JDMITRCinci/RJAAI003_204.png[/IMG]

Dec 12, 2008 | 1995 Honda Odyssey

1 Answer

UK Headlights to French Headlights


The headlamps themselves will look identical. If you were to look at the beam pattern of the light, then it would be different. Your original headlights were designed to throw excess light to the passenger side of the road (I.E. away from oncoming cars). Now that driving directions are opposite in France, your old headlights would be throwing the excess light into the oncoming cars, blinding them). The new lights are designed to throw the light away from those oncoming cars.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 18, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
2006 Honda Odyssey Logo

673 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...