Question about 2000 Hyundai Elantra

1 Answer

Blinkers don't work

I have a 1990 Pontiac Bonneville and the turn signals won't come on. They will, however, come on as hazard lights. I checked the fuses and they're okay.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

If you are somewhat mechanically inclined then try taking the steering colume apart and checking the blinker handle take apart to try and fix the problem or get a new from a scrap yard or your dealer

Posted on Jul 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Pontiac Bonneville no turn signals or lights in the dash the fuse isnt blown either


As far as the turn signal, did you check the proper fuse for voltage. Even if the fuse is good, if no voltage, the circuit is still dead. The turn fuse goes hot with key on, turn on the key, check fuse circuit for voltage, use a test lite or something. I hope you can read diagram?

26290676-3omtbjp4r4esnhpbq2uccvz4-3-0.jpg

Sep 24, 2016 | 1990 Pontiac Bonneville

1 Answer

I have a 1991 celica and for some reason the front signals does not work at all. When I turn on the blinkers it blink really fast on both sides but hazard light works fine it blinks normal but it...


check the main earth wire near the battery. and one near the rear of the lights. unbolt them and clean the connectors up put some grease on them after. then check again. remember that when the earth wires come off the radio code will be needed to reset the the radio. be safe and take the battery off.

Sep 28, 2013 | Cars & Trucks

1 Answer

I have a 1990 Mercury Cougar. Several problems...Blinkers, hazards, horn, and break lights are not working. However the break light in the back window comes on when the break is pressed. Checked fused and...


I am unaware of what a "CO" display is.
Now with the blinkers, hazard, horn and brake lights not working that may be the multi funtion switch (blinker switch) that is located inside the column (where the blinker lever attaches).
Obviously the blinker, hazard and horn will all work off of something in the column. Brake lights, you may think a switch on the pedal.

the brake lights do work with that switch but when you have the kind of tail lights where a turn signal light shares the same bulb as a brake light, the brake light is cancelled for the turn signal by running through the multi function switch inside the column.
The third brake light does not blink so its not on that same circuit.

Oct 07, 2011 | 1990 Mercury Cougar

1 Answer

Flashers work but turn signals will not 1989 bonneville


There are usually two flashers that are used on most cars. One for the turn signals and one for the hazard lights. They are usually located under the dash. If you don't know what they look like, then go to the parts store and ask to see a new one. Once you locate both of them, see if they have the same part number stamped on them. If they do, then switch them and see if the signals work.
REMEMBER : The key must be turned on for the turn signals to work in most cases. The hazard flashers will work with the key off.
If the signals work, then replace the turn signal flasher. I hope this information is helpful and thank you for using Fixya.com.

Jun 25, 2011 | Pontiac Bonneville Cars & Trucks

2 Answers

I have a 1995 grand prix Blinkers dont work but, other lights do.


First check turn signal fuse and relay if, they are good then try pressing on and off the hazard switch while turning the signal switch on.If signals start to work replace hazard switch.If hazard switch is good then replace turn signal switch.

May 02, 2011 | 1995 Pontiac Grand Prix

1 Answer

No break lights, blinkers or hazzards. I changed the fuses. That wasn't it. Still No breaks, blinkers or hazards. Where is the relay?


I would check the turn signal/ hazard flasher module, its on the brake pedal bracket, 5 wires, turn the hazards on and give the side of it a few raps with a screwdriver and see if it starts flashing. The PINK should have 12v. If that checks out good it may need the turn signal switch. At the turn signal switch there is a WHITE wire that should have 12v when the brake is depressed, then you should have 12 on the DARK GREEN and the YELLOW wires coming out. If the center high mounted light works, then the brake switch at the pedal is good.

Nov 19, 2010 | 2002 Pontiac Sunfire

1 Answer

1990 Corsica: the brake lights work but the blinkers dont...


does the hazard signals work? if they do, then replace all turn signal bulbs.

May 06, 2010 | 1990 Chevrolet Corsica

2 Answers

Hazards and blinkers not working


There are separate fuses for the turn signals and blinkers, but you should check both of them just to see if they're good.

You may have a burnt out turn signal bulb as well. I know that this sounds like an obvious answer, but a single bulb can sometimes disable the entire system because of the way that some flashers operate.

You could also have a defective turn signal/hazard light flasher. This is located under the dash board on the driver's side between the steering column and the door. You have to remove the sound insulation/kick panel (the cover on the bottom of the dash board) to reach the flasher (it is easy to remove - I don't think you even need tools).

May 16, 2009 | 1997 Pontiac Grand Am

2 Answers

Turn signals don't work but hazards do on 1995 bonneville pontiac


Hi,

Try Check or replace the turn signal switch. It might have loose connections or its faulty.

Feb 08, 2009 | 1996 Pontiac Bonneville SE CA Value

Not finding what you are looking for?
2000 Hyundai Elantra Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...