Question about 1987 Chevrolet Blazer

1 Answer

Slip out when in 2 wheel

My blazer slips out of gear when in two wheel but not when in 4. if i shift back into either then back into drive it will shift in to gear but will slip out again.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,140 Answers

Check fluid level. Sounds like transfer case problem.

Posted on Jul 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trans troubleshooting


If you are driving in 4 wheel drive on hard surface then you have drive line torque lock up as there is no centre diff to allow the front and rear wheels to equalise out the torque . 4 wheel drive is for use when on dirt / snow / ice where the differences between the front and back are allowed to slip the tyres . Jack up a rear wheel and allow the torque to dissipate by rotating a wheel . A point from all 4x4 manufacturers is that you NEVER drive in 4 wheel drive unless you are on dirt or ice/snow conditions. You have probably been getting away with it as any bump that lifts a wheel from the road surface will allow the wheel to slip. Even running the tyre on the white painted line on the road or any wet patch on the road will help ease the torque loading

Feb 01, 2014 | Cars & Trucks

1 Answer

Chevy blazer 4 wheel shifts


check your oil level may be low.

Dec 20, 2013 | Cars & Trucks

2 Answers

When I'm in 4 wd the front wheels feel like the brakes are being applied when I make a sharp turn. No problems when driving straight or in 2 wd.


It sounds like you are driving in 4wd drive on dry pavement. The front drive axles do not work like the rear differential. When you turn, the outside front wheel must travel farther than the inside wheel, therefore they are traveling through the turn at different speeds. If you are on dry pavement, this causes the gears to bind. You don't notice this on slick surfaces because the outside wheel will slip instead of bind up the gears. You should not use 4wd on dry pavement. That's the advantage of push button, or shift on the fly, 4wd. You can shift back to 2wd when you encounter dry pavement. All wheel drive vehicles don't have this problem because they have a limited slip front differential as opposed to a locking differential on 4wd. Hope I didn;t confuse you too much.

Dec 21, 2010 | 2004 Ford Ranger

1 Answer

98 blazer seems to go in 4 wheel drive. as it is driven it makes a loud pop/bang sound fron transfer case is it disingaging, slipping, broken gear?


most likely the chain has streched and is slapping against the case and or jumping teeth on the gears either way it's not minor.

Jul 31, 2010 | 1998 Chevrolet Blazer

1 Answer

1995 chevy blazer transmission will not let truck shift out of second when in drive


Normally while driving in overdrive (4th gear) you will feel it start slipping and finally slide into third gear. Then 3rd gear slips out into second, and you will never see 3rd or 4th gear again. I'm guessing this was the problem? If so its time for an overhaul

Dec 22, 2009 | 1995 Chevrolet Blazer

1 Answer

2002 envoy makes a slipping noise when put into


sound like shift motor is slipping trying to rotate sector shaft to go in gear.

Dec 08, 2009 | 2002 GMC Envoy

1 Answer

We bought a 1995 jeep grand cherokee orvis edition...the truck will not go into reverse...it makes a wierd grinding noise


Be sure that the truck is fully engaged in two wheel drive. It may have slipped out of gear on the transfer-case. Move the lever for 2 and 4 wheel drive back and forth a few times before shifting transmission.Good luck

Apr 25, 2009 | 1995 Jeep Grand Cherokee

1 Answer

4x4 problems


What make, model, and year is your truck? Does it have AWD or just 4-wheel drive? What selector knob to you have for 4x4 (gear shifter or electrical switch?) Does your vehicle have limited slip or locking differentials? If you have an electrical selector with locking (limited slip) diffs and AWD, that is normal for it to automatically switch into 4x4 when you loose traction.

Jan 22, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...