I how do I mount EZ-pass since the radio antenna surrounds the rear view mirror and is built into the glass and is a dot pattern? I have a 2007 Honda CRV. Thanks for any guidance.

The piece that is on the glass is glued on with an ultra violet cured adhesive, or a two part epoxy adhesive. The last one I did was cured by the sun in 24 hours (mix, set and cure).

https://www.youtube.com/watch?v=8IBp0Pkoa24

Gluing it back on

https://www.google.com/search?q=fixing+rear+view+mirror+mounting+plate

Permatex® Rear-view Mirror Repair Kit - Canadian Tire

https://www.canadiantire.ca > ... > Interior Car Mirrors
Jan 23, 2022 - Permatex® Rear-view Mirror Repair Kit contains everything required for making professional quality repairs in just minutes Two part adhesive ...
Mount Style: Adhesive
Assembled Weight (kg): 1.00 kg
Assembled Weight (lb): 2.20 lb
Assembled Width (mm): 10.00 mm Rating: 3.3 · ‎$6.49

How to Fix a Rearview Mirror - NAPA Know How Blog

https://knowhow.napaonline.com > how-to-fix-a-rearvi...
Jul 30, 2020 - Most rearview mirror repair kits only come with the glue components, some come with a replacement metal glue-on tab, but you still need a couple ...

Permatex® Rearview Mirror Adhesive Kit

https://www.permatex.com > products > permatex-rearv...
Permatex's Rearview Mirror Adhesive contains everything required for making professional quality repairs in just minutes. This repair kit includes ...

Rearview Mirror Repair Kit - Princess Auto

https://www.princessauto.com > product
Home · Auto Repair · Chemicals, Adhesives and Lubricants · Adhesives and Sealants · Instant Adhesives; Rearview Mirror Repair Kit.

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

I am assuming you are talking about the interior rear view mirror and not the side rear view mirror. Most auto parts stores sell an adhesive glue to fix the interior rear view mirror. Most of these mirrors have two parts to them. One part is the bracket that glues to the windshield and the other part is the rear view mirror assembly. Before gluing the bracket to the glass check and see how the mirror assembly attaches to the bracket. There will often be a screw that fixed the two together.

SECTION 501-09: Rear View Mirrors 2002 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.

NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors

1. Position the glass in the full up position.

1. Locate the notch at the bottom of the exterior mirror glass.

1. Release the exterior mirror glass.
   1. Insert a long flat-bladed screwdriver in the notch.
   1. Push the screwdriver into the notch until the glass is released.

Heated mirrors

1. Position aside the exterior mirror glass.

1. Disconnect the electrical connectors.

All mirrors

1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.

Installation
Heated mirrors

1. Connect the electrical connectors.

All mirrors

1. Position the exterior mirror glass on the exterior mirror motor.

1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation

1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
   

1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
   

1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
   

1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
   

1. To install reverse Removal procedure.
   

------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove front door trim panel (23942). Refer to Section 01-05 .
   

Trim Panels, Door Front—Town Car
Removal

1. Snap out two door pull strap retaining screw covers. Remove screws.
   

1. Remove three screws on front and rear side and center of front door trim panel (23942).
   

1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
   
   Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
   

1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.
   
   Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
   

1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
   

1. Remove the door trim panel.
   

1. Disconnect two electrical connectors.
   

1. Remove nut from outside rear view mirror mounting base.
   

1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
   

1. Remove screw from outside rear view mirror base.
   

1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
   

1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
   

If the mount is still on the glass, loosen the set screw that holds the mirror to it and slide it off. If the mount fell off the windshield, you can get special glue to re-attach it at any parts store for around $10.00 Key to replacing it is to mark the correct position on the outside of the glass with a crayon and to make sure the windshield is very clean where you are re-attaching. follow the package instructions exactly and make sure you hold the mount in place without sliding it around, till it has adhered. Don't hang the mirror for at least twelve hours. While the mirror is removed, lube the pivot joints so it will adjust easily to avoid pulling it off the windshield again.

is it just the glass that broke?

Exterior Mirror Glass Removal

1. Position the inner edge or the exterior rear view mirror glass to its maximum travel.

1. WARNING: Place a shop towel between the exterior rear view mirror glass and the hand to avoid personal injury in the instance of glass breakage.
   Grasp the outboard edge of the exterior rear view mirror glass and pull outward.

1. Remove the exterior rear view mirror glass.
   • If equipped, disconnect the heated rear view mirror glass electrical connectors.

Installation

1. If equipped, connect the heated rear view mirror glass electrical connectors.

1. NOTE: An audible click will be heard during installation.
   Press firmly in the center of the exterior rear view mirror glass until it snaps onto the exterior rear view mirror motor.

for radio

Visual Inspection Chart Mechanical Electrical

• Audio unit
• Antenna or antenna cable
• audio speakers mounting/speaker cones
• Radio ignition interference capacitor, radio frequency interference suppression bond

• Central junction box (CJB) fuses:
  • 19 (10A)
  • 12 (5A)
• Battery junction box (BJB) fuses:
  • 19 (40A)
  • 20 (40A)
  • 27 (10A)
• Connectors
• Ignition switch
• Circuitry
• Audio unit

for mirrors

Visual Inspection Chart Mechanical Electrical

• Exterior rear view mirror(s)
• Interior rear view mirror

• Central junction box (CJB) Fuse(s):
  • 8 (10A)
  • 16 (10A)
• Circuitry
• Exterior rear view mirror motor(s)
• Exterior mirror control switch
• Heated rear window switch

are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.

1. Remove the front door trim panel; refer to Section 501-05 .
2. go to car-part.com for a used mirror. Page with * is cheapest seller.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect the electrical connector.
   1. Remove the speaker.

1. Remove the outside rear view mirror (17682).
   1. Disconnect the power mirror wiring clips.
   1. Remove the outside rear view mirror nuts.
   1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).

------------------------------------------------------

----------------------------
SECTION 501-09: Rear View Mirrors 2001 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass, 2001 model Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors

1. Position the glass in the full up position.

1. Locate the notch at the bottom of the exterior mirror glass.

1. Release the exterior mirror glass.
   1. Insert a long flat-bladed screwdriver in the notch.
   1. Push the screwdriver into the notch until the glass is released.

Heated mirrors

1. Position aside the exterior mirror glass.

1. Disconnect the electrical connectors.

All mirrors

1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.

Installation
Heated mirrors

1. Connect the electrical connectors.

All mirrors

1. Position the exterior mirror glass on the exterior mirror motor.

1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

auto parts stores sell an adhesive to glue the metal mount tab back to the glass.