Question about 1999 Dodge Durango

1 Answer

Durango shuts off

My Durango shuts off after running for a little while, I have replaced the crankshaft sensor - no change. What now? Any suggestions?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,776 Answers

If the check engine light is on, take the vehicle to an autoparts store and have them scan the computer for fault code(s). Most parts stores offer this service at no charge. Getting the codes will go a long way toward figuring out what the problem might be. Hope this helped and best wishes.

Posted on Jul 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 99 Durango 5.9 rpm goes up and down rep. Crsen wires plugs cap rotor bug still runs really rough


Check to see if all the vacuum hoses are connected to the right source.
Regards
Sir Dana

Apr 27, 2017 | Dodge Cars & Trucks

1 Answer

2003 dodge durango while driving lost acceleration, shut it off, restarted then drove fine for about 4 miles did the same thing but this time it didn't want to start. After a couple minutes it started


sounds like the crankshaft sensor gets warm and then opens up, once cooled off it closes again ( it is a transformer in epoxy housing ) I would replace it.

Apr 28, 2015 | 2003 Dodge Durango

1 Answer

Troubleshoot crank position sensor location


For testing crank sensor,check the help link below:---How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html
----------

How to test Crankshaft Position CKP Sensor?

---------------
Crankshaft Position Sensor Operation?

----------------
Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
----------
GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html

------------
These details will help.
Thanks.

Nov 25, 2012 | 2000 Cadillac Escalade

1 Answer

The check engine light recently came on in my 2004 Honda Civic and the car proceeded to lose power and shut off repeatedly. After running the diagnostic it indicated that the crankshaft sensor needed to...


Check engine light means emissions control system failure.
I would only rely on Honda to properly diagnose this and
replace component failure with Honda part. The ck engine
light was probably reset when your mechanic replaced the
crankshaft sensor, and in time, came back on cause the
problem has not been corrected.

Jan 21, 2011 | 2004 Honda Civic

2 Answers

99 dodge durango keeps shuttin down every so often cleaned battery cables and replaced clamps on both terminals worked for a day then same thing and security light will come on if i unhook pos cable and...


2002 Durango shuts down without warning. Sit for about 30-45 min and will restart, run for a while, and shut down again. Shows "NO BUS" code. Took it to Dodge Dealer and had a diagnostic done....nothing!!! Have changed PCM, crank shaft sensor and am getting ready to RUN IT OFF A CLIFF if I can get it running long enough!!! It is a black hole and we are getting no where!! I can't even sell the dang thing!!

Aug 14, 2009 | 1999 Dodge Durango

1 Answer

Crankshaft sensor 1999 Durango


what engine?if it's a 5.2 l V8,you could remove right inner fender shield for easier access..i would not remove trans..if you remove trans and then install sensor to engine,you could break it reinstalling trans..if it's a 4.7..sensor is in block..these can be really tough to get out..rust forms behind sensor and it will not come out..most times these come out in pieces

Jul 19, 2009 | 1999 Dodge Durango

2 Answers

Problem with crankshaft sensor


no you dont have to remove the transmission it on the passenger side under a bracket at the corner of the tranny. if you remove the backet you have easy access. i changed mine in thirty minutes.

Jul 19, 2009 | 1999 Dodge Durango

2 Answers

2000 Dodge durango wont start after driving for a while.


i had the same problem in a dodge ram pick up. ended up being the coil. when the coil got hot my truck would die or not start again until the engine had cooled down. replaced the coil, and whalaaaaah. no more trouble. good luck!!!!!!!!!!!!!!

Apr 21, 2009 | 2000 Dodge Durango

Not finding what you are looking for?
1999 Dodge Durango Logo

Related Topics:

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...