Question about 1994 GMC Suburban

1 Answer

1994 gmc rear axle removal how to

1994 gmc rear axle removal to fix wheel bearing

Posted by on

  • 2 more comments 
  • yadayada
    yadayada May 11, 2010

    what is the differential you have? dana or spicer, 1/4 ton, dual wheel, 1 ton? what?

  • anthony pyke Oct 08, 2013

    1 ton

  • Anonymous Mar 16, 2014

    How do you change the rear bearings on adult 3 wheel trike ? There are four sets bearings on the axle that runs from wheel to wheel

  • Anonymous Mar 16, 2014

    How do you change the rear bearings on adult 3 wheel trike ? There are four sets bearings on the axle that runs from wheel to wheel

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 97 Answers

-Remove tire and brake drum
-put drain pan under axle housing
-remove rear axle housing cover (10 or 12 bolts)
-turn gear untiil the bolt for cross shaft shows and remov e the bolt
-remove the cross shaft.
-push axle in until you can remove "U" clip from axle and axle will pull out,
Remove seal, you need a pulller to remove axle brg.

Posted on Jul 26, 2009

  • j Stozek Jul 08, 2013

    does not address problem

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I change rear wheel bearings on my 1992 GMC Safari van


Put the rear up on jack stands and remove the wheels and brake drums. Then unbolt the rear differential cover and drain the gear oil. Then, you remove the pinion securing bolt. DO NOT ROTATE THE WHEELS AS THIS CAN CAUSE THE PINION GEARS TO FALL OUT. Push the rear axle shaft inward toward the vehicle and remove the "C" clip that secures the axle to the pinion gears. Then pull the axle shaft outward and out of the axle housing. Inspect the axle shaft for scuffing and excessive wear on the place where the wheel bearings rest. If there is excessive wear, you can use a "repair bearing", which is modified to install so it runs on an unworn part of the axle shaft. Otherwise a regular replacement bearing is fine. You need a slide hammer removal tool to extract the old bearing from the axle housing, and a bearing install tool to insert the new one without damage. Once the new bearing is in, reinsert the axle shaft, secure with the "C" clip, and pull outward to latch the "C" clip into its recess. Install the pinion bolt. Reinstall the differential cover with appropriate gasket or sealer. Fill differential with approved gear oil in the recommended amount. Ensure that if the rear is a positraction rear end there may be an additive required to the gear oil for proper operation.

Sep 24, 2015 | GMC Cars & Trucks

1 Answer

How do I replace drivers side rear wheel bearing on 2005 gmc sierra with drum brakes?


not very much info. 1/2 ton? 2wd? If it is a standard pickup there are "C" clips that hold the axles in. You will have to remove the 3rd member cover and remove the clip. This is after you have removed the wheel and brake drum. The axle will slide out and the bearing will remain in the axle housing.Messy job. Take it to your mechanic.

Dec 06, 2014 | GMC Sierra 1500 Cars & Trucks

1 Answer

Replacing a rear wheel bearing 1996 gmc sonoma 5 speed what all is involved does the axle have to come out or can you just take wheel and brakes drum off etc.


To remove the rear axle to replace a bearing you have to remove the rear differential cover and remove the small retaining bolt holds the spider gear shaft in place and then slide this shaft out far enough to remove the "C" shaped axle shaft retaining clip. Once this clip is off then the axle can be slid out and the bearing & seal replaced. Make sure that none of the spider gears or thrust washers behind them get out of place and you should use a new retaining bolt when reassembling the differential components as they come [or should come this way] with thread locker to prevent them from coming loose.

Jun 22, 2010 | 1996 GMC Sonoma

1 Answer

Rear Wheel Seal & Bearing on 1999 GMC Safari Van


Yes you do have to pull the axle and make sure you put everything back in the same place you removed it from. The ring and pinion shouldn't have to be bothered. You will have to remove the rear end cover to remove the axle. Its very easy to do. There is a pin inside the rear end that has to be removed to pull the axle. Pay attention to how you take it out and put it back the same way. It sounds as if you can do this with no problem.

Apr 11, 2010 | 2000 GMC Safari

1 Answer

How to get the rear wheel bearing out of 99 gmc jimmy


Dear Jimmy,
This repair is an intrusive repair if you have never done it.A chilton's manual can be purchased at your local auto parts store for $20 for your vehicle. Jack up the rear of vehicle and support it.Remove the rear tires.If the vehicle came with disc brakes remove the caliper and bridge, if not then remove the brake drum.Remove the rear diff cover, with a drain pan to catch the fluid.Remove your rear pinch thru bolt, your pin will then slide thru.Push both axles in to release and remove the u clips on the inside of the carrier assy, then pull both axles out.Remove the outer axle seal, throw away, ten using a bearing puller tool remove the bearing from the axle tube, install new bearing ad seal with drivers and reinstall axles.any other questions get back to me...I'm here to help!!!

Nov 21, 2009 | 2000 GMC Jimmy

1 Answer

Squeeky rear wheel bearing. How is it removed and replaced?


This is a rear wheel drive vehicle? Are you sure it's not a brake squeal?
The bearing sits in the end of the axle tube and is lubed with the differential fluid. You need to dissasemble the differential to remove the axle, to remove the bearing. You need a puller for that type of bearing.

Sep 08, 2009 | 1994 Chevrolet Caprice Classic

1 Answer

Can't get left rear axle out to replace bearing


you must remove the cover on the rear end, remove the 5/16" bolt on center carrier, push the pin that the bolt whent through out, thenp push the axle in, a c clip will fall out of the carrier then axle may be removed,

May 26, 2009 | 1994 GMC Suburban

1 Answer

How do you remove right rear axle on a 2004 ford crown vic to replace seal on wheel?


Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
Removal
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.
  1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .




  1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.
  1. Drain rear axle lubricant by removing the axle housing cover .
  1. Remove differential pinion shaft lock pin and differential pinion shaft .


    9979cb3.gif
  1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .



  1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.
Installation
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.
  1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .
  1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .
  1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.




    NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
  1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).



  1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).
  1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).
  1. Install rear disc brake caliper and rear disc brake rotor .
  1. Install wheels and tires.
---------------------------------------------------------
  1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.

    Rear Disc Brake Caliper Anchor Plate




  1. Lubricate the rear wheel bearing with Rear Axle Lubricant.



  1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.



    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
  1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .



  1. Install axle shafts as outlined.

May 13, 2009 | 2004 Ford Crown Victoria

1 Answer

Need to know how to change rear wheel bearing in a 95 suburban


jack & support vehicle. remove rear axle cover drain fluid, removeleft rear tire drum/rotor brakes, remove bolt in axle housing that holds the 3/4 inch pin in place pull pin , push left axle shaft inwards and remove c clip from inside axle case,slide out axle shaft,remove seal,remove bearing and install in revers

Jan 16, 2009 | 2003 GMC Sierra

2 Answers

How to replace front wheel bearing on 2003 GMC ENVOY


Jack up vehicle and support with jack stands
Take off wheel
remove brake caliper
remove caliper bracket
remove rotor
remove axle retaining nut cotter pin
remove axle retaining nut
remove axle from output flange
pull axle out of vehicle
hub and bearing assembly held in by 4 bolts

installation is reverse of removal. You will need to find out the torque specs for the axle retaining nut.

Jan 14, 2009 | 2002 GMC Envoy

Not finding what you are looking for?
1994 GMC Suburban Logo

1,534 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...