Question about 1992 Chevrolet S-10

2 Answers

I have a 92 s-10 blazer, brake lights an running lights dont work

I just recently replaced my brake lights and running lights. when ever i turn my running lights on my right rear running light comes on but left rear stays off also when running lights are on my right side turn signals are on as well. But still when ever the brake pedal is depressed my brake lights still do not work???

Posted by on

  • raymond20256 Jul 26, 2009

    i checked the wiring twice and everything was fine

  • raymond20256 Jul 26, 2009

    i checked the wiring twice and everything was fine

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 94 Answers

I just recently replaced my brake lights and running lights

are you sure you wired everything correctly?
check again especially your grounds

Posted on Jul 26, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 2,899 Answers

There's a switch on the brake pedal arm that controls the brake stop lights, that needs adjustment or replacement.
Hope this helps.

Posted on Apr 04, 2015

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: Left turn signal stops flashing when brake pedal is depressed.

there is a ground problem, most likely in the tail unit itself, but a ground problem is hard to find and easy to fix. reground the system, the turning unit, and the problem should stop. About the hazards, I don't know...... some times in older cars, that is the way it works. because the brake and hazard element in the bulb is the same and the old cars used a break in the power, but the new cars use a break in the ground. any way, chase the ground down first, it is usually the cause.

Posted on Feb 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All signal lights dont work. l checked the fuses and its not the problem


My 95 blazer has the same problem. I didn't have brake lights, blinkers, or high beams. Just running lights and low beams. Turns out many people have this problem with Blazers. My issue with my blazer turned out to be the hazard switch on the steering column. The metal connectors under the switch don't make proper contact sometimes. I found a "sweet" spot in the switch by pushing it down till I noticed the lights working properly. Then I duct taped it down and they work now. Not the best solution but a quick fix and a good place to start trouble shooting.

Jan 22, 2013 | 1995 Chevrolet Blazer

2 Answers

Hi: I have a 1998 Chevy Blazer 4.3 The brake lights and turn signals don't work.... HELP


Sounds like you have a bad multiple function turn signal switch. A couple things to try With your foot pressing on the brake pedal, Press the four way flasher button up and down, press and hold it down, pull up on it, or wiggle it. If the brake lights come on during any one of those replace the switch. With the key in the run position pull, push, the turn signal lever slightly. If the turn signal or brake lights start to work replace the switch. Let me know if none of those work, they usually do, and I'll get you some more in depth diagnostic info.

Jun 17, 2011 | 1998 Chevrolet Blazer

2 Answers

2001 chevy blazer all lights work except the brake lights. The third top light works but not the bottom. Bulbs are good and no fuses are out.


does the 4 ways work? if they do it would be the brake light switch at the brake peddle,,,,,,,,, if they dont the problem is in that red hazerd switch on your steering colum inside it has 3 spring loaded pads that make 3 electrical contacts each so 9 in all and they get sticky from dirt, dust & coffee and hot chocolite dumped on them and stick and burn out. and your brake lights stop working... I could tell you how to fix it but rather diagnose what it is first

Jun 11, 2009 | 2001 Chevrolet Blazer

2 Answers

No brake lights on 2001 chevy blazer LT 2wd


Check your wires, the smoke could mean an electrical fire.

Jun 03, 2009 | 2001 Chevrolet Blazer

2 Answers

Right rear brake light and blinker dont work


when you use the right turn signal, does it blink faster?. Could it be the bulb holder is damaged or rusty?

May 16, 2009 | 2001 Plymouth Neon

1 Answer

Lower brake lights dont work,third light does


Turn signal switch 95% of t he time. Try to work your hazards, if it stuck at all will also cause this.

Feb 10, 2009 | 1998 Chevrolet Blazer

3 Answers

No turn signals or brake lights on left and right but brake light on top


I agree. My brake light dont work. Only the third brake light does. The running lights work but when i apply the brakes the rear tails dont light up.
I currently have this issue along with the signals dont work unless I bang the top of the steering colum. The hazard switch doesnt work either. If the signals dont work it makes this very quick clicking sound on the passenger side. I checked the fuses and they are good. The bulbs still work. The brake switch works cause the third brake light goes on. And seeing as I am having a problem with signals.....GM says I have to replace the switch in the steerg colume. Its a little box about the size of a cigarette pack. If you take apart the panels off ( right behind the steering wheel, where the hazard switch is) ...that is where it is located. Its plugged into the signal lever. Hope this helpa....Good luck everyone with this issue.

Oct 17, 2008 | 2001 Chevrolet Blazer

Not finding what you are looking for?
1992 Chevrolet S-10 Logo

403 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...