Question about 1998 Honda CR-V

1 Answer

Oil is spiling out from the side of the engine

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 672 Answers

You have a leaking seal. Possible valve cover, cam, crank, balancer seal. If its coming from within the timing cover, you will need a timing belt and cam,balancer, crank seal replacement. It's also recommended to replace the waterpump while performing this repair(if it hasnt been done recently).

Posted on Jul 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 96 tt 993 is accumulating oil in the intercooler and then spiling down to the left side onto the engine, is there an easy fix to this problem?


If oil is accumulting inside the inetercooler, it means that the turbo-shaft seal is leaking causing oil to by pass in to the intake system, then through to your intercooler. A quick check to see if this is a fault, remove the hose/piping from the turbo the intercooler and place a piece of white paper over the hole at the turbo where the air is dispelled. Run the engine for a few minutes and if you notice any oil occuring/building up on the white papaer, then it is the turbo seal. This method is used on everything from jetskis to dump trucks. If no oil is present then the oil leak will be coming from somewhere else on the engine, and being sucked in through to the top of the intercooler. May have to remove it to see where any other leaks are coming from.

Jan 22, 2011 | 1996 Porsche 911 Turbo 3.6

2 Answers

Were is the drain plug located on a 2007 chevy 5.3 on the passenger side of engine . is it behind the ac unit. i want to put a engine block heater in.


The block drain is on the passenger side of the engine, in the center of the block near where the oil pan attatches to the block.

Engine Block Plugs/Sensors


Engine Block Plugs/Sensors
100 - Engine Block
100 - Engine Block
101 - Oil Gallery Plug - Front
110 - O-Ring
111 - Oil Gallery Plug - Rear
112 - Oil Gallery Plug - Side
113 - Washer
114 - Engine Coolant Heater
115 - Washer
116 - Oil Gallery Plug - Side
117 - Washer
130 - Transmission Housing Locating Pin
145 - Washer
146 - Engine Block Coolant Drain Hole Plug
701 - Crankshaft Position (CKP) Sensor
702 - O-Ring
718 - Knock Sensor
718 - Knock Sensor
739 - Bolt
739 - Bolt
750 - CKP Sensor Bolt

Oct 19, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Turn on car and the motor oil starts spiling


you have a major leak somewhere. Inspect your engine top to bottom for this leak. DO NOT RUN THE ENGINE severe damage may occur!!

Sep 29, 2010 | 1992 Honda Accord

1 Answer

I have a problem on the 1st and second gear sensor as when i engage the drive gear there is a hard sound coming from the gear box and there is oil spiling and when yu start to accelerate there is a loud...


Bring vehicle to a transmission shop ASAP. If the spilling oil is automatic transmission fluid (ATF) ( usually pink but Honda has been known to use regular oils in transmissions )your leaking ATF and its affecting the subject gears.

Sep 02, 2010 | 2000 Honda CR-V

2 Answers

Where is the engine oil filter on the engine block?


Oil filter is on the drivers side, all the way back on the side of the block, close to where the transmission bolt's up to the engine block.

Jul 13, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

Oil pressure switch location on 1999 chev cavalier


The oil pressure switch relays the oil pressure in the engine to the instrument cluster. The switch will illuminate the OIL PRESSURE light if the oil pressure drops below 2psi (13 pa). The switch is usually located on the side of the engine, under the intake manifold on the 2.2L engine and on the side of the intake camshaft housing on the 2.3L/2.4L engine.


7fef8ab.jpg

Fig. 1: The oil pressure switch is located on the engine block under the intake manifold and is accessible from underneath the vehicle-2.2L engine

bdee34a.jpg

Fig. 2: Oil pressure switch location-2.3L/2.4L engine


Other, the low oil level switch activates the OIL light in the instrument cluster when the oil level in the pan goes below a certain level. The switch is mounted on the oil pan.


Hope this helped (remember rated this post).

Apr 11, 2010 | 1999 Chevrolet Cavalier

1 Answer

Where is the oil sending unit on a 1996 ford taurus 3.0 liter engine located? glenn


On 3.0L OHV engines, the oil pressure sensor is located on the left side of the engine block above the flywheel. On 3.0L DOHC engines the sensor is located on the left side of the engine block above the oil filter. On 3.4L DOHC engines the sensor is screwed into the oil filter adapter. The oil pressure sensor operates the oil pressure warning lamp.

71f6e37.jpg
Fig. 1: Location of the oil pressure sensor-3.0L OHV engines


046f42b.jpg Fig. 2: Location of the oil pressure sensor-3.0L DOHC engines

69cce3e.jpg

Fig. 3. The oil pressure sensor-3.0L OHV engine

Hope help with this (remember rated this help). Good luck.

Feb 18, 2010 | 1996 Ford Taurus

1 Answer

Oil leak passenger side 300 turbo sedan, some on front passenger side wheel. Never lost oil pressure, but dipstick showed very little oil in crankcase on immediate after-run check. Have not started...


Add about 2.5-quarts of new engine oil to the engine.
Remove the passenger-side wheel, and support the car on jack-stands.
Start the engine and look for oil leak.
Chances are leaks are coming from failed oil-pan gasket or the drain-plug.
The head-cover gasket could be failing as well..

Nov 30, 2009 | 1985 Mercedes-Benz 300

1 Answer

Oil pressure is fine. Oiling only to the pass side valve train.


The 3.1/3.4 engines are built the same way. The oil goes through the cam bearings then to the lifters, then the push rods to the rocker arms. The last engine I seen that had a weird problem had the cam bearings spun. Unfortunately there is no easy way to check for this problem short of disassembling the engine.

The other possibility would be bad lifters but loosing half of the engine lifters wouldn't be possible. Sometimes the pushrods wear on the contact areas also but not usually half an engine.

This isn't going to be easy, Good luck.

Nov 02, 2009 | 2005 Chevrolet Impala

1 Answer

7mge have oil leak


hi if your engine 22R front engine first in side timing cover where engine bully fitted there is oil seal, next valve cover front side between cover and head there seal not like oil seal half cercle shap it makes leak also front side of the camshaft there is oil seal..

Sep 12, 2008 | 1989 Toyota Cressida

Not finding what you are looking for?
1998 Honda CR-V Logo

Related Topics:

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...