Need picture of battery cable and battery location to install. New battery's in 2014 gem e 2

Generic Electronic Module (GEM)-Generic Electronic/Central Timer (GEM/CTM) Removal
NOTE: The GEM must be reconfigured upon replacement. Refer to the scan tool help screen on the Ford Service Function (FSF) card to program tire size and axle ratio.

1. CAUTION: Electronic modules are sensitive to electrical charges. If exposed to these charges, damage may result.Disconnect the battery ground cable. For additional information, refer to Section 414-01.

1. CAUTION: Use care when removing the instrument panel steering column cover (044F08) or damage to the cover locating tab may occur.Remove the instrument panel steering column cover.
   1. Unlock the retainers.
   1. Remove the instrument panel steering column cover.

1. Disconnect the bulkhead connectors from the instrument panel fuse junction panel.
   1. Loosen the bolts.
   1. Disconnect the bulkhead connectors.

1. Position the instrument panel fuse junction panel aside.
   1. Remove the nuts.
   1. Remove the bolts.

1. Remove the generic electronic module/central timer module (GEM/CTM).
   1. Disconnect the electrical connectors.
   1. Remove the screws.
   1. Remove the GEM/CTM.

1. To install, reverse the removal procedure.

I believe ford calls it a gem module.

https://s22.postimg.org/6pga2lqyp/gem_module.jpg

Click on the link. Ford calls it a Gem module.
The number one step was, disconnect negative battery cable. I couldn't get everything in one picture. Hope it helps. I found that info in my database.

Module - Generic Electronic (GEM)/Central Timer (CTM) Removal

1. CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. Depower the supplemental restraint system (SRS). For additional information, refer to Section 501-20B .

1. Remove the audio unit. For additional information, refer to Section 415-01 .

1. Remove the center instrument panel finish panel.
   1. Remove the screws.
   1. Remove the center instrument panel finish panel.
   • Disconnect the electrical connectors.
   • Remove the GEM/CTM.
     1. Remove the screw.
1. Disconnect the four connectors from the GEM/CTM.
1. Remove the GEM/CTM.
2. Installation
1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

Special Tool(s) Radio Removing Tool
415-001 (T87P-19061-A) Removal

1. Remove the radio chassis.
   1. Insert Radio Removing Tool into the radio face plate and release the radio retaining clips.
   1. Pull outward on Radio Removing Tool to remove the radio chassis from the instrument panel.
   3. Remove the radio.
      1. Disconnect the electrical connectors.
      1. Disconnect the radio antenna lead in cable.
      1. Remove the radio.

Ford , Lincoln , Mercury in that era called a GEM generic electronic module .
The generic electronic module (GEM) constantly monitors its subsystems for concerns. If a concern is found in one of the subsystems, the GEM will record the concern in the form of a diagnostic trouble code (DTC).
The ignition switch position is very important to the GEM function. Often times, erratic or unexpected GEM function can be traced to problems with these GEM inputs.
The GEM controls the following features:

• Wipers/washers (front/rear).
• Warning chimes.
• Battery saver.
• Illuminated entry and courtesy lamps.
• Driver power window.
• Accessory delay.
• 4-wheel drive.
• Heated back lite/mirror.

Generic Electronic Module (GEM) C239
Behind center of I/P CAUTION: Prior to removal of the module, it is necessary to upload module configuration information to scan tool. This information needs to be downloaded into the new module once installed. For additional information, refer to Section 418-01 .
CAUTION: Electronic modules are sensitive to electrical charges. If exposed to these charges, damage may result.

In this model year Ford calls the BCM- Generic Electronic Module (GEM) It is located , Behind center of I/P !
Module - Generic Electronic (GEM)/Central Timer (CTM) Removal

1. CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result.
   Depower the supplemental restraint system (SRS). For additional information, refer to Section 501-20B .

1. Remove the audio unit. For additional information, refer to Section 415-01 .

1. Remove the center instrument panel finish panel.
   1. Remove the screws.
   1. Remove the center instrument panel finish panel.
   • Disconnect the electrical connectors.

Remove the GEM/CTM.

1. Remove the screw.

1. Disconnect the four connectors from the GEM/CTM.

1. Remove the GEM/CTM.

Installation

1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
   To install, reverse the removal procedure

The module on this truck year is called a "GEM", BCM comes later. The GEM is located behind the radio assembly and is bolted to the IP support bracket, it has 3 large connectors. See photo below.
The following is from Alldata:

>>Prior to removal of module, it is necessary to upload module configuration information to New Generation STAR (NGS) Tester. This information needs to be downloaded into the new module once installed.
Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result<<

then after install:

>>To install, reverse the removal procedure. CAUTION: Once the new module is installed, it is necessary to download the module configuration information from the New Generation STAR (NGS) Tester into the new module. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

No smart junction box , GEM - generic electronic module ! this module energizes the relays in the battery junction box ! The gem module is behind the center of the dash !
Generic Electronic Module (GEM) Removal and Installation

1. > CAUTION: Prior to removal of the generic electronic module (GEM), it is necessary to upload module configuration information to the diagnostic tool. This information needs to be downloaded into the new module once installed. For additional information, refer to Section 418-01 .
   Depower the supplemental restraint system (SRS). For additional information, refer to Section 501-20B .

1. Remove the radio chassis. For additional information, refer to Section 415-01 .

1. Remove the center instrument panel finish panel.
   1. Remove the screws.
   1. Remove the center instrument panel finish panel.
   • Disconnect electrical connectors.
   • Module Controlled Functions The multifunction modules consist of the following:
     
     • generic electronic module (GEM)
     • central security module
     The GEM controls the following features:
     
     • front wiper and washer
     • warning chime
     • battery saver
     • illuminated entry and interior lighting
     • driver one-touch down power window (optional)
     • battery saver relay
     • door ajar warning indicator lamp
     • safety belt warning indicator lamp
     The central security module controls the following features:
     
     • remote keyless entry
     • computer-operated lock system
     • trim switch unlock inhibit
     It's more then likely to have DTC'S diagnostic trouble codes stored in it's memory !
   • B1431 Wiper Brake/Run Relay Circuit Failure GEM REFER to Section 501-16 . B1432 Wiper Brake/Run Relay Circuit Short to Battery GEM REFER to Section 501-16 . B1434 Wiper Hi/Low Speed Relay Circuit Failure GEM REFER to Section 501-16 . B1436 Wiper Hi/Low Speed Relay Circuit Short to Battery GEM REFER to Section 501-16 . B1438 Wiper Mode Select Switch Circuit Failure GEM REFER to Section 501-16 . B1441 Wiper Mode Select Switch Circuit Short to Ground GEM REFER to Section 501-16 . B1446 Wiper Park Sense Circuit Failure GEM REFER to Section 501-16 . B1450 Wiper Wash/Delay Switch Circuit Failure GEM REFER to Section 501-16 . B1453 Wiper Wash/Delay Switch Circuit Short to Ground GEM REFER to Section 501-16 . B1458 Wiper Washer Pump Motor Relay Circuit Failure GEM REFER to Section 501-16 . B1460 Wiper Washer Pump Motor Relay Circuit Short to Battery GEM REFER to Section 501-16 . B1462 Safety Belt Switch Circuit Failure GEM REFER to Section 413-09 . B1466 Wiper Hi/Low Speed Not Switching GEM REFER to Section 501-16 . B1473 Wiper Low Speed Circuit Motor Failure GEM REFER to Section 501-16 . B1476 Wiper High Speed Circuit Motor Failure GEM REFER to Section 501-16 Your wipers do not work at all ? did you check this fuse Central Junction Box (CJB) fuse 16 (30A)
   • • The wipers are inoperative
     • Central junction box (CJB) fuse:
       • 16 (30A)
     • Circuitry.
     • GEM.
     • Multifunction switch.
     • Wiper run/park relay.
     • Wiper HI/LO relay.
     • Wiper motor.
     • GO to Pinpoint Test A .
     Before replacing parts you need to test , check for codes !

It sounds like something is drawing power with the key off. It could be the GEM module but I doubt it. There is a draw somewhere. Connect battery and pull fuses one at a time to see if curent drain stops. You will need an ampmeter in series with the battery and the postive cable. Expensive. Get one from pick n pull salvage yard real cheap.

Check the following fuse junction panel fuses: fuse 23 (5A), fuse 20 (5A), and fuse 8 (5A).

Section 13-09A: Gauges/Warning Devices, Chime/Buzzer System 1998 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/16/1998
Generic Electronic Module (GEM) Removal
The generic electronic module (GEM) is connected to the rear of the fuse junction panel (14A067) .

1. Disconnect battery ground cable (14301) . Refer to Section 14-01.
   

1. Remove two nuts retaining fuse junction panel to dash panel (01610) .
   

1. Pull upper ears of fuse junction panel down out of retaining bracket.
   

1. Disengage locking tangs and disconnect three harness connectors from bottom of GEM.
   

1. Turn fuse junction panel over and remove screw retaining GEM to fuse junction panel .
   

1. Disconnect and remove GEM from fuse junction panel .
   

Installation

1. Follow removal procedure in reverse order.
   

1. Tighten GEM to fuse junction panel screw to 1-2 Nm (9-17 lb-in).
   

1. Tighten fuse junction panel retaining nuts to 4-6 Nm (36-53 lb-in).
   
   
   
   
   
   Item Part Number Description 1 14B205 Generic Electronic Module (GEM) 2 - Mounting Ear (Part of 14A067) 3 14A067 Fuse Junction Panel 4 - Screw (Part of 14A067) 5 - Generic Electronic Module (GEM) to Fuse Junction Panel Connector A - Tighten to 1-2 Nm (9-17 Lb-In)

here it is but you must have it configured.

Generic Electronic Module (GEM) —Generic Electronic/Central Timer (GEM/CTM) Removal
NOTE: The GEM must be reconfigured upon replacement. Refer to the scan tool help screen on the Ford Service Function (FSF) card to program tire size and axle ratio.

1. CAUTION: Electronic modules are sensitive to electrical charges. If exposed to these charges, damage may result.
   Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
2. CAUTION: Use care when removing the instrument panel steering column cover (044F08) or damage to the cover locating tab may occur.
   Remove the instrument panel steering column cover.
   1. Unlock the retainers.
   1. Remove the instrument panel steering column cover.
3. Disconnect the bulkhead connectors from the instrument panel fuse junction panel.
   1. Loosen the bolts.
1. Disconnect the bulkhead connectors.
4. Position the instrument panel fuse junction panel aside.
5. Remove the nuts.
6. Remove the bolts.
7. Remove the generic electronic module/central timer module (GEM/CTM).
   1. Disconnect the electrical connectors.
   1. Remove the screws.
   1. Remove the GEM/CTM.

it's by the gas pedal.

The multifunction module consists of the generic electronic module (GEM).
The GEM controls the following features:

• interval rear window wiper
• battery saver
• illuminated entry
• headlamp control
• interior lamp control
• power door locks
• remote keyless entry (RKE)
• accessory delay
• perimeter anti-theft system
• door ajar output control

Generic Electronic Module (GEM) 2003 escape Removal and Installation

1. NOTE: Prior to removal of the GEM, it is necessary to upload module configuration information to a diagnostic tool. This information needs to be downloaded into the new module once installed. For additional information, refer to Section 418-01 .
   Disconnect the battery ground cable. For additional information, refer to Section 414-01 .

1. Remove the pin-type retainer and the lower shield.

1. Position the RH and LH carpet aside from the center tunnel.
2. Disconnect the GEM electrical connectors.

1. Remove the GEM
   1. Pull back the insulation and remove the nuts.
   1. Remove the GEM.
2. To install, reverse the removal procedure.
   • Configure the GEM. Refer to Section 418-01 .