Question about 2005 Nissan Quest

2 Answers

Vibration changed all four rotors,new pads.cant get vibration to stop

Posted by on

  • Mike Butler
    Mike Butler May 11, 2010

    Vibration all the time or only when brakes applied?

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 520 Answers

If the vibration only occurs when applying the brake pedal then the problem still lies with the rotors. They may have been warped again after they were reinstalled and the lug nuts were tightened down. This is a common problem that happens when proper torque is not applied. If the vibration is occuring all of the time at different speeds without applying the brake then the problem is either going to be bad alignment or unbalanced tires. It is also possible to have vibration problems from bad ball joints and wheel bearings. Hope this helps, good luck!

Posted on Jul 26, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 105 Answers

Most likely you have a problem with your calipers and how they are gripping with abs assist control on rotor.

Posted on Jul 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 chevy silverado. When braking truck start to vibrate. Changed front and rear rotors and brake pads. Just bought new tires.


I know on my Malibu the pads for the side against the caliper piston is different than the pad on the other side of the rotor.

Feb 03, 2014 | Chevrolet Cars & Trucks

1 Answer

Truck shakes when brake is applied upon slowing down it gets shakier until i let off the brake and pulse the brakes till truck stops


A common cause for the vibration when braking is when front brake pads are replaced, but the brake rotors were not resurfaced smooth. Overtime when braking, the new pad will wear into the rotor that was not cut. The uncut rotor, having high and low spots when turning, will cause the brake pedal to vibrate/pulse when stopping.

Sep 16, 2011 | 1998 GMC Sierra

1 Answer

My car is shaky every time i hit a stop light?


you should keep all four tires on the ground !!!! LOL ! your rotors or brake pads are bad. do you feel it shake in the steering wheel ? Check these three items and im sure it will fix.......1) jack front car up and try to move front tires in all directions, does it feel loose at all? if yes check tie rod ends, upper and lower ball joints. 2) check brake pads for wear, heat from pads warp the rotors and cause the break pedal and steering to shake or vibrate. 3) If nothing can be found wrong with the tie rods or ball joints i recommend changing the rotors and brake pads, a pretty cheap fix.

Jan 21, 2011 | 2005 Dodge Neon

1 Answer

2006 freestyle was just inspected by a ford dealer 4 days ago. according to the technician, pads and rotors are good. The car vibrates alot when brakes are applied for an average stop. I can feel the...


a visual inspection would not show up a warped disc/rotor,so as a first step(cheapest)i would change both front rotors/pads but buy genuine parts.(rotors only last about 50/60k before you need to change them anyway)and as mentioned to another person,by the time you buy the bits, take the wheels off,remove the calipers etc you might as well take it to autozone and keep your hands clean.....it only takes an hour, tops....

Jul 23, 2010 | 2006 Ford Freestyle

3 Answers

350z Rotors need to be cut at only 10K miles


Your rotors should be fine but it also depends on who turned the rotors and how they were done.Considering the dealer replaced the pads they probably used a metallic pad which have been known to be a noisy .Id suggest you have a repair shop resurface your rotors again and install some ceramic brake pads.

Jan 30, 2010 | 2005 Nissan 350Z

2 Answers

Brakes are starting to grind really bad and car vibrates when im coming to a stop. any idea what may be going on with my brakes?


Its most likely time to change those break pads, and shoes, also wouldnt hurt to get an alignment while your at it... hope this helps!

Jul 31, 2009 | Mitsubishi Galant Cars & Trucks

2 Answers

Pulsating and vibrating brakes on 2003 chevy express, new pads and rotors


Rust build up is commonly found on the hubs sandwiched by the rotors/hubs

May 15, 2009 | 2003 Chevrolet Express

1 Answer

Ford 1988 escort GL-Front wheel constant scrape-scrape,vibration


sounds like you need new brake pads and the rotors atleast turned down if not replaced
the pads should stop the noise and the rotors should stop the vibration/wobble
thanks wes
ps please rate me

Mar 27, 2009 | 1988 Ford Escort EXP

1 Answer

Honda Odessey 2002 - Rotor brake


Yes, depending on the quality of the rotor, in extreme conditions it can rust out quicker. The brake pad graps the rotor, 'cleaning' it as it stops the vehicle. If the vehicle sits for a long period of time then it is more likely to accumulate rust. If a rotor gets out of balance, (this is what causes your vibration) it needs to be remachined. The rotor can only be machined so many times before it is too thin to use. The rear rotor must be thinner than the front rotor. Since this is a vital part of your brake system, it's money well spent to help insure your safety.

Jun 19, 2008 | 2002 Honda Odyssey

Not finding what you are looking for?
2005 Nissan Quest Logo

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...