Question about 1996 Chevrolet C1500

1 Answer

Rebuild done now wont start

92 k15 ran last weekend when pulled in. Did head swap with rebuilts, new gaskets new distributor new throttle position sensor new cap button pugs and wires. I have gas, spark "at the plugs" and it rols but does NOTHING HELP

Posted by on

  • zacharymicha Jul 26, 2009

    The timing was set at #1 TDC and then i adlusted the distributor and placed #1 wire on the button and rewired all the plugs one by one

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 335 Answers

Is the timing correct?

Posted on Jul 26, 2009

  • Moe Jul 26, 2009

    If the engine has fuel, spark, compression and is timed it should start and run. Is the engine multi port or throttle body ?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my ktm sx85 2014 keep blowing head gaskets??? Blown the head gasket at fatcats other weekend, had a top end rebuild and head ported checked waterpump etc.. carb cleaned and checked run lovely last...


Did you have the flatness of the block deck checked? Same thing for the head flatness. If one or both are not flat, then you will continue blowing head gaskets. Also, you can try using Blue Devil sealer. It can seal most head gasket leaks wiout tearing the heads off again.

Dec 08, 2014 | Cars & Trucks

1 Answer

I rebuilt the TBI, Changed every sensor in the truck and replaced the heads. I still cannot pass the CA smog test


Check everything that is connected to a vacuum line, check the CAT and the injectors and last run a compression test.

Mar 13, 2014 | 1988 Chevrolet K2500

1 Answer

Will start but wont stay running


sounds more like a fuel issue. fuel pressure should be checked.

Sep 09, 2017 | Mazda Protege Cars & Trucks

2 Answers

Died while driving and wont start


CK your distributor rotor ....pull it off and look in side the hole where it fit on the distributor shaft if it really black in side replace it . If OK then either your ignition module ( inside the distributor a little black block with wires going to both end of it ) or the Stator inside the distributor has shorted out . The stator is kinda hard to change if you don't have the right tools . i think rebuilt distributors from the parts store have gotten a lot cheaper then they use to be ; you may want to change the whole thing a new one will come with a new module and stator

Aug 05, 2012 | 1992 GMC Yukon

1 Answer

92 jeep wrangler 4 cyl 5 speed skipping and bogging down idling rough replaced fuel pump/filter injector o rings fuel pressure regulator timing chain distributor plugs wires map sensor crank sensor idle...


Have you checked the cam sensor? Also does that vehicle have a "throttle position sensor"? Some cars use both MAP and MAF sensors, not sure about your particular vehicle but if it is one of those, cleaning the MAF wouldn't hurt. Good luck.

Jun 28, 2012 | Cars & Trucks

1 Answer

Hello i have a 92 nissan 240sx just got car started after installing head gasket car ran great all day other than a small surge under mild throttle, later that night when i went to start the car now i have...


When replacing head gasket you had to disconnect and move spark plug wires and coil wire.Sounds to me if it ran for a little while then died out look for a burned wire by exhaust manifold.Something must of shorted out.Thats why it ran a little while and died.

Feb 10, 2011 | 1992 Nissan 240SX Fastback

1 Answer

Coolant blowing out of radiator into overflow bottle at start up.


Typically would not overheat until enough coolant was lost. Find out if they mag fluxed the heads, or had it done. A lot of shops rebuild without doing this step as it's expensive. If they got a rebuilt head, again they need to know if it was mag-fluxed.
It's harder to mag flux the block while in the vehicle and assembled.

Dec 12, 2009 | 1990 Mitsubishi Montero

1 Answer

Dead 92' Ford Econoline


Have you tried replacing the coil?

Jul 21, 2009 | 1992 Ford Econoline

Not finding what you are looking for?
1996 Chevrolet C1500 Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...