Question about 1995 Nissan Altima

2 Answers

LOCATING CRANK SHAFT POISITION SENSOR ON 2002 NISSAN 2.5

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

I had a hard time locating the sensor too. I went to the dealership and they gave me the schematic. I tracked down by following the schematic

Posted on Aug 01, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 146 Answers

The crankshaft position sensor is located on the back side of the engine, in the engine block near the oil pan towards the transmission. If you take the engine cover off of the top of the engine and look down the back of the block past the intake you can see the sensor and the harness going to it.

Posted on Jul 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Service engine soon


Check for any loose wire harness connection or bad contacts.

Aug 18, 2008 | 2002 Nissan Maxima

1 Answer

2002 Nissan Altima crank shaft censor located bank 2


there is only one crankshaft sensor so you will be looking for a CAM shaft sensor for it to be on bank 2
go google and type in --location of cam shaft sensors on nissan altima engine ---

Dec 18, 2016 | Nissan Cars & Trucks

1 Answer

Where is the cam sensor in a 2002 nissan quest?


HI Chuck! The cam position sensor is inside the distributor on the quest. If the cam sensor has gone bad you need to replace the distributor assembly as it is not servicable. Before replacing the distributor, take the cap off and make sure the rotor is turning when you crank the engine. If it is not then check the timing belt as the distributor is driven by the cam shaft. If the belt is broken the cam shaft will not turn and you could get this code.The cam sensor is located under the plastic cover located under the rotor button

Nov 18, 2016 | Nissan Cars & Trucks

1 Answer

Where are the 2 crank shaft sensors in a 2003 nissan altima


There is one crank sensor and it is: 1) Looking at the front of the car it is on the back side of the engine. 2) Just behind where the flywheel is located.

Aug 02, 2011 | 2003 Nissan Altima

1 Answer

I am getting an error code for cam shaft sensors on a 2002 Nissan max. Is is complicated to go under the hood and replace them?


It is not difficult. It is located on the timing cover on the passenger side of the engine. You'll see a wire harness going to a hall effect sensor with a 10mm bolt. They should cost around $80.

However, there was also a Recall in 2003, ID# 46615 involving a bad solder joint on the crank and cam sensor control boards. You can read about it here:

http://www.internetautoguide.com/10-12-2002-59-897/2002-nissan-maxima-recalls.html

Best wishes

Jan 01, 2011 | 2002 Nissan Maxima

2 Answers

2002 Altima 2.5 is now giving me problems like it doesn't want to start...it is not the alternator, battery or starter. Very frustrating because it starts when it wants to..


I would be looking towards the crank angle sensor failure. Its located right above the passenger side drive shaft, where it goes into the trans. Good luck

Aug 19, 2009 | 2003 Nissan Altima

2 Answers

Where crank shaft and camshaft?


There are two cam shaft sensors and one crank sensor Nissian did sell a kit at one time with all the sensors in it one cam sensor is in the left cylinder head a one is in the right cylinder head

May 29, 2009 | 2002 Nissan Altima

1 Answer

Where crank shaft and camshaft?


The camshaft position sensor is located on the timing cover, near the top of the motor. The crankshaft position sensor is located on the same timing cover near the crankshaft. Just a side note, more than likely the crankshaft position is your issue and it's under a recall from Nissan and they will replace it for free.

May 23, 2009 | 2002 Nissan Altima

2 Answers

CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA


1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.

Dec 18, 2008 | 2005 Nissan Altima

Not finding what you are looking for?
1995 Nissan Altima Logo

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...