Question about 2002 Toyota Camry

Open Question

What is the torque spec for the nut that holds on the windshield wiper arm for a toyota camry 2002?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
justuscc
  • 360 Answers

SOURCE: replacing windshield washer wiper switch on 2000 Toyota Camry

pretty easy just remove the plastic shroud around the switch there is phillips sloted screws and you should be able to access the wiper switch good luck

Posted on Sep 18, 2008

Ad
  • 22 Answers

SOURCE: 98 camry windshield wiper

You will have to change the swich that control the wiper blades cause sometimes they go bad

Posted on Dec 17, 2008

  • 124 Answers

SOURCE: 2006 Toyota Tacoma. What is the spec torque for

100 lbs should do it

Posted on Apr 10, 2009

  • 1861 Answers

SOURCE: need torque specs for a 2002 toyota camry 2.4 for

The 2002 2.4 engine head bolts are 'torqued to distance'.

First, install all the bolts, and, in a sequential fashion, starting at the innermost, working outward, torque all bolts to 70 N-m/806 kgf-cm/58 foot lbs.

Next, mark the front side of each head bolt with a dot of paint. Retighten te cylinder head bolts 90 degrees, starting at the inner 2, and working outward.

We hope that this helps you out.

Posted on Dec 29, 2009

thandragni
  • 101 Answers

SOURCE: TOYOTA HILUX 2006 engine head torque specs

it depends on the size of the screws. i recommend to set torque as 100lbs for new bolts, 90 for old bolts

Posted on Feb 29, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Drivers windshield wiper not working


Common problem is that the nut holding the arm on has loosened. Right at the pivot point on the arm is a nut underneath a pop off cover. You should be able to take that off. Tap the arm down far enough to grab the post again and tighten the nut. The only thing that would stand in your way is if the arm connection or the post is stripped in which case you will have to replace the wiper arm, the wiper mechanism, or both.

Feb 26, 2015 | 2002 Isuzu Rodeo

1 Answer

Find the torque specification for a 2007 corolla windshield wiper arm nut


Good luck finding that torque spec. Tighten it until you can't tighten it anymore.

Feb 21, 2015 | 2007 Toyota Corolla

1 Answer

Torque for windshield wiper arm on 2007 escape


hand tighten with a 3/8 drive rachet-you don't need to tighten it like you're wrestling a grizzly- cheers Denny

Nov 27, 2013 | 2007 Ford Escape Hybrid FWD

4 Answers

How to remove windshield wiper arms?


pull the wiper arm up, pull the wiper back then pull it hard down the wiper arm once the loop releases the wiper.

Mar 09, 2011 | 2000 Saturn L-Series

2 Answers

Rear windshield wiper does not cover the intended area how to remove rear windshield wiper arm


IF YOU HAVE A PLASTIC CAP ON ARM REMOVE IT AND THE NUT UNDER IT, AND LIFT WIPER ARM OFF.

Jan 02, 2011 | 2000 Dodge Caravan

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

1 Answer

I installed a new wiper motor. I ran it before installing the wiper arms. it will not stop at zero. it over travels down into the cowling. I try to rest them higher then they stop some where in the middle...


Try to run the motor without the wiper arms tightened down and turn it off so it can cycle down to its rest state. Then install the wiper arms.

Make sure, that the car's windshield wiper wiring is correct for this motor.
---
Wiper Arm & Blade Removal & Installation Front To Remove:
CAUTION
When the wipers are parked (off), the driver’s wiper arm must be above the passenger’s wiper arm.
  1. Remove the clip holding the outside end of the wiper arm cover to the arm.
  2. Lift the arm cap up to expose the nut.
  3. Remove the wiper arm mounting nut.
  4. Using a suitable two jaw puller, remove the wiper arm from the wiper pivot.
To Install:
  1. Verify that the wiper motor and linkage are in the parked position.
  2. Place the wiper arm in position over the wiper pivot.
  3. Install the nut to hold the wiper arm to the wiper pivot. Torque nut to 26 ft. lbs. (35 Nm). CAUTION
    Make sure to tighten the wiper arm nut properly.
  4. Push the arm cap cover down.
  5. Secure the clip holding the cover to the wiper arm.
Rear To Remove:
  1. Lift and hold the wiper arm away from the rear window.
  2. Lift the lock securing the wiper arm to the pivot.
  3. Slowly release the wiper arm so it rests against the lock.
  4. Remove the wiper arm from the pivot.
To Install:
  1. Install the wiper arm on the pivot.
  2. Pull the arm outward and release the lock.
  3. Gently release the wiper arm until it rests on the rear window.
prev.gif next.gif

Aug 22, 2010 | 1996 Dodge Grand Caravan

1 Answer

Removing rear windshield wiper arm on 94 4Runner


on the wiper arm, there is a cap. remove cap and there is a nut underneath, remove nut spray wd40 oil on the threads that are exposed, then slowly wiggle arm and pull simultaneously to remove.

Jun 11, 2010 | 1994 Toyota 4Runner

1 Answer

Ford f150 windshield wiper bushing diagram. windshield wipers are not working , motor is going and the wiper arms will move freely when truck is not on


sounds like a loose nut. there are nuts that hold the wiper arms on, they may be under a cover but theyre at the base of the wiper arm. also there's a nut that holds the wiper linkage onto the wiper motor. if you can move the wipers independently, it's the nuts connecting the wiper arms.if you move one arm and the other moves with it, it's the nut holding the linkage to the motor.

Feb 17, 2010 | 2000 Ford F150 Flareside SuperCab

Not finding what you are looking for?
2002 Toyota Camry Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...