Question about Ford Edge

2 Answers

Iwant to know what is the possible cause. engine not start but it is cranking. ford car.. edge 2009 model. i check in IDS. no DTC found,, i replace CKP. Sensor but still no start. can you help me what the other possible cause of this. thanks. regard team.

Posted by on

  • bumblebee77 Jul 26, 2009

    no im not use fuel pressure. but fuel pump is working..



    because i remove fuel rail in the top in the engine. what you said,,



    check if fuel is come. when i do ignition on @ off.. fuel is available.



    accuallly i check the in data logger RPM during cranking but no respond during cracking.



    only that please can help me..



    thanks

  • bumblebee77 Jul 27, 2009

    okey i will check....



    power train is including for my pin point test..





    thanks for that.. i try to swap power train.



×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 76,691 Answers

Do u have fuel pressure? the test port is on the top of the engimne is the fuel supply rail to the fuel injectors

Posted on Jul 26, 2009

  • yadayada
    yadayada Jul 26, 2009

    poss defective powertrain control module

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,185 Answers

If it is a 2009 model it is still under warranty so why are you trying to fix it.

However
You will need a hand with the next bit

When you turn over the engine over is there anything coming out of the exhaust (Gas or LIquids)

If not then the catylist may have collapsed and this will not allow the gasses to escape from the engine causing back pressure which stops the engine from putting fuel into the cylinders.

You have checked the fuel coming from the pump have you cracked an injector pipe to see if it is reaching the cylinders .

Have you removed a spark plug and laid it on the engine block to see if there is a spark being produced at the plug tip.

Is the engine cranking over fast enough on the battery.

Have you been in a very dusty environment where the Air Filter can get blocked.

Let me know

Posted on Jul 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Ford f 150 4.2liter Check engine light P0352


Does your f150 have coil on plug or coil pack ignition system !
P0352 - Ignition Coil B Primary/Secondary Circuit Malfunction Description: See the description for DTC P0350. Possible Causes: See the possible causes for DTC P0350. Diagnostic Aids: See the diagnostic aids for DTC P0350. Application Key On Engine Off Key On Engine Running Continuous Memory Coil-on-plug (COP) ignition testing - GO to JF1 GO to JF1 Coil pack ignition testing - GO to JE1 GO to JE1
What this code is say is there is an open in the coil electrical circuit . Had this code on a few ford's where the problem was the PCM - engine computer ! Spark plug gap got worn so far as to cause the coil to break down and send 20,000 volts to the coil control transistor inside the engine computer . Watch this video !
Ford 5 4 shorted coil primary winding and bad computer driver Doesn't matter this is a 5.4 L , works the same way !

Jan 02, 2017 | Ford Cars & Trucks

2 Answers

Lincoln tow car 2001 passive anti tip DTC 1260 I replaced pcm.trancevier.instrument cluster.2new ignition key but no communication this module what possible problem this?


No where in the DTC - description does it say anything about replacing any modules . An does not have anything to do with a communication problem ! You need a professional grade scan tool to communicate with the PATS system ! An if you don't know these thing's you better take it to pro !!!!!!!
P1260 - Theft Detected - Vehicle Immobilized Indicates that the passive anti-theft system (PATS) has determined a theft condition existed and the engine is disabled. This DTC is a good indicator to check the PATS for DTCs.
  • Previous theft condition
  • Anti-Theft System failure
Theft indicator flashing rapidly or on solid when ignition switch is in the ON position. Check anti-theft system for DTCs. Typical vehicle symptoms are: Start/Stall or Crank/No Start. NOTE: No crank symptom only on vehicles equipped with PATS starter disable feature

Apr 04, 2015 | 2001 Lincoln Town Car

1 Answer

Sometimes wont start in park pistion, will always start in netural.


There can be a little wear in the shift linkage and you may be able to adjust the linkage so that it works better. This is providing the "no start" situation means that the engine does not crank in Park sometimes.

If the problem you are reporting in Park is that it cranks alright but does not run, then that would be a different problem.

Oct 12, 2013 | 2009 Ford Edge SE

1 Answer

I have a 1998 chevy silverado check engine code 1345a what does this mean


Do you mean Diagnostic Test Code (DTC) P1345 ?This DTC is a "Manufacturer Specific" code that is defined by GM as "Camshaft/Crankshaft Correlation Error".

It is basically telling you that your Cam/Crank timing is not within specifications.

Possible causes are:

> Improperly installed distributor assembly
> Badly worn distributor shaft or bushings
> Worn timing components (chain, gears, etc.)

Proper diagnosis is required to diagnose the actual condition that is causing this code. If any timing components are replaced, a scan tool capable of reading live computer data is required to check the cam/crank offset PID and make adjustments as necessary.

The specification for Cam/Crank offset is (Zero) 0 +/- 2 and must be checked with the engine running at 1500 RPM.

Jun 03, 2012 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

Van will not start code p0725 what to do


Without knowing make or model Po725 is a Chrysler code for Engine Speed Sensor Circuit
Possible Causes- - Open or shorted CKP sensor circuit condition
- Poor CKP sensor electrical connection
- Check communication error between the ECM and TCM
- Failed CKP Sensor
When is the code detected- The P0725 Codes is triggered when TCM does not receive the engine speed signal from ECM. Chrysler description- The Engine Control Module (ECM) monitors the engine speed through the Crankshaft Position (CKP) sensor with the engine running, and send signal to the Transmission Control Module (TCM

May 09, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

Check engine light on. has dtc of p1309. what could it be? I replaced cam sensor but code is still there.


Code PO1309 : Misfire Monitor Failure Description : When the misfire monitor is disabled,usually due to the input signal generated by the camshaft position sensor, by sensing the passage of teeth from the camshaft position wheel. Possible Causes : PCM(power train control module), Mass Air Flow Sensor, Engine Coolant Temperature Sensor, Crank Shaft Position Sensor, Camshaft Position Sensor.

Jan 08, 2010 | 2001 Ford Taurus

1 Answer

2004 tuarus does not start.


ford dealerships have a scanner called an IDS.you will need to find out that code for the CEL that will start you on your path to fixing it.is it possible that due to the cranking the engine is SEVERELY flooded and new spark plugs will have to be installed?i would need more info as to what happened before the car started acting up.

Dec 22, 2008 | 2004 Ford Taurus

3 Answers

1997 ford powerstroke DTC codes


autozone has repair manuals from haynes they generally have the code lists in them hope this helps

Aug 23, 2008 | 1997 Ford F350 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...