Question about 1992 Mercury Capri

Open Question

Light and beeping sound for air bag

1992 mercury capri non turbo
air bag light and alarm beeper will not stop. is there a reset or can I temporarily disarm untill I find a solution?

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76070 Answers

SOURCE: 1992 Mercury Capri IAT

it is located in and is a part of the airflow meter.

Posted on Sep 29, 2009

Ad
Molson02536
  • 3854 Answers

SOURCE: Where is my IAT sensor located? Its a 1992 Mercury

Save your money and don't attach the module, it does not work. It only works during idle and after that the O2 and MAP sensors take over to control the air fuel ratio and timing. Take note that if there is a conflict with the program to your ecm's parameters, your engine will run under limp mode default which would result in less HP and performance. Good luck and if you need ore performance just spend the extra to have your car Dyno Turned. 

Posted on Sep 30, 2009

  • 191 Answers

SOURCE: Mercury Capri IAT

This is a very good online manual for the Capri.


http://www.techcapri.com/Repair/Capri_Service_Manual.htm

Posted on Oct 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WIll not start


Crankshaft positioning sensor Replaced?
(More Info)
We Are Here To Help !!


Donald Deane MCSE,ASE,CPO

Jul 29, 2017 | 1992 Mercury Capri

1 Answer

Beeping noise in 1995 Chrysler LeBaron 3.0 turbo


PUT IN A NEW IGNITION SWITCH. THE KEY BUZZER IS INTERGRAL TO THE IGNITION SWITCH. IT ALARMS WHEN KEY IS LEFT IN THE CAR OR IF IT IS BROKEN IT ALARMS FOR ALL YOUR REASONS.

Oct 11, 2012 | Chrysler LeBaron Cars & Trucks

2 Answers

As I let off my throttle petal, my 1993 Mercury Capri 1.6 (non-turbo) decelerates instantly, in a jerky action. I there an adjustable regulator for this problem? Thanks, J Kelley, FL


Your throttle position sensor could be bad. Try finding a used one at a junk yard, they are +$100 new if you can find one...Chris

Jan 03, 2012 | 1993 Mercury Capri

1 Answer

Have 1992 capri non turbo when it gets hot it acks like it floods out and shuts down then you have to wait a couple minutes with the gas pedal to the floor before it will restart replaced the o2 sencer but...


This may be electrical. The ignition control modules commonly get heat sensitive on the capris (its happened to me twice), causing car to shut down at hot temps. Replace the igniter at the same time, bet this will fix it. Igniter is inside the distributer, module is on the outside of the dist..good luck...Chris

Oct 03, 2011 | 1992 Mercury Capri

1 Answer

My 1991 non-turbo Mercury Capri started fine last night but while idling, the Air Bag light began to flash and the Battery light came on. Not wanting to travel I turned off the ignition switch. ...


charge the battery and once fully charged, do a LOAD test on it, clean all the connections and start the car ,, check the voltage at the battery posts with the car running, you should get between 13.5 and 14.5 volts, if not, replace the alternator , if you do, the battery and the cables just needed some attention

Jul 17, 2011 | 1991 Mercury Capri

3 Answers

Where is my IAT sensor located? Its a 1992 Mercury Capri non Turbo. I bought a Performance module and its splices into the two IAT wires. Is


Save your money and don't attach the module, it does not work. It only works during idle and after that the O2 and MAP sensors take over to control the air fuel ratio and timing. Take note that if there is a conflict with the program to your ecm's parameters, your engine will run under limp mode default which would result in less HP and performance. Good luck and if you need ore performance just spend the extra to have your car Dyno Turned. 

Sep 30, 2009 | 1992 Mercury Capri

1 Answer

1992 Mercury Capri IAT


it is located in and is a part of the airflow meter.

Sep 29, 2009 | 1992 Mercury Capri

1 Answer

Mercury capri alternator getting very hot


its the alternator pulley thats defective and in order to pull the alternator you a have to take off the piece with the hoses on it above the alternator and you can wiggle it out

Dec 09, 2008 | 1992 Mercury Capri

Not finding what you are looking for?
1992 Mercury Capri Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

fordexpert

Level 3 Expert

5516 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...