Question about 2001 BMW 5 Series

1 Answer

How to install blower motor

There is 12v going to the resister but the fan does not respond. How do i get it out, any web links on how to replace the blower motor?

Posted by on

  • Biggs1 Jul 26, 2009

    How do you do that with everything in place.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 83 Answers

Before you condem the blower motor. Jump the motor manually to insure it works.

Posted on Jul 26, 2009

  • David Borysowski Jul 26, 2009

    Remove the 2 wire connector from the motor. install one pin from a good ground to one terminal of motor. Install another jumper wire from a good power soarce(+) to other terminal on motor.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is located the fan speed control stratus 01


Could be your blower motor resister,it's located by blower motor,easy to remove.Click here to see blower motor resistor.

Dec 26, 2012 | 2001 Dodge Stratus

Tip

Blower motor problems


If ,and when,your blower motor has problems,and it will not blow on the low speeds, consider the blower resister,it is what controls the speeds for your blower motor.Now,replacing the blower resister is the thing to do,but two things to check for also,,the connector to the blower resister,and to the back of the fan select switch,the one you control,on the dash.These connectors,including the fan switch can be burned,and need replacing also.Now the reason these go out,and burn,and melt the connectors,is,that the blower motor is pulling too many amps,even though the blower motor runs great,and sounds good,trust me,the blower motor is the reason,so replace all of these parts when you replace the resister.If the connectors are fine,and the blower switch is fine,of course they will not need to be replaced,but the blower motor is a must,or you just might have to do it all over again in a few months,along with the switch,and connectors I mentioned.

on Jul 20, 2010 | Chevrolet C1500 Cars & Trucks

2 Answers

Where is the blower motor resister located at for my 2002 town and country limited van


Blower motor resistor It will be inline to the blower motor wires but here is how it is postion the resistor a wound wire and the resistor is attach facing inboard of the blower fan,thy do it like that to cool the resistor out, it will be attatch by two bolts in the blower fan area I made you a picture just to get the ideacansmo_2.png

Apr 26, 2011 | Chrysler Town & Country Cars & Trucks

2 Answers

Heater bower won't blow


There is a blower motor relay,near the motor i think,check it.

Apr 12, 2010 | 1998 Ford Contour

1 Answer

Hi i have a chrysler Grand voyager 2005, the heating started not switch on and then not switch off. there is 12v accross the input of the heating assembly and the controller seems to be functioning...


there is a balast resister or what everone call it blower motor resister these go bad so you can lose your speeds on your blower motor the resister is in the blower box on the back side replace it and your good to go

Mar 09, 2010 | 2000 Chrysler Grand Voyager

2 Answers

I have a 1999 Jeep Wrangler and the heater fan stopped working for all the fan speeds. The fuses are fine. How do you know if it is the blower resistor or the blower motor?


If you bypass the resistor pack and connect the motor directly to the fused 12v supply then the fan should run at maximum speed. If so, it's the resistor pack that's blown: a very common fault on a huge number of makes and models.

Feb 13, 2010 | 1999 Jeep Wrangler

1 Answer

2000 Ford Taurus - A/C fan only works on high; cool air is "available" but not blown as fan won't run, except in "high" position. Any suggestions?


The low speeds(all of them) are distributed threw the fan speed switch to the blower motor resister.The resister is the problem.It is located very near the blower motor.It has two screws mounting it to the blower box.It has a plug in with about 5 to 7 wires.Unplug this plug to the resister.Remove the screws.Pull the resister toward you,it mounts and rest inside of the blower case,this is how it is cooled.Now when you replace the resister,replace the blower motor.Even if the bower motor is running fine, it is pulling to many amps for the resister.It will happen again soon,if you don`t replace the blower motor.If I can help you any more,please let me know.

Aug 31, 2009 | 2000 Ford Taurus

1 Answer

Where is the front fan resistor unit?


Look under the van,on the drivers side near the radiator,it should be in that area.Follow the wires from the fans,they should go right to the module.This is for the cooling fans for the radiator.For the resister module for the blower motor look near the blower motor in the blower box.It is near the blower fan.It can be under hood,but it will be mounted with two screws.Remove the two screws,but you need to remove the wire plug in first.Pull it out .It goes inside of the blower box.If you replace this module,replace the blower motor also,because the blower motor is what causes the resistor to burn out.Did you check voltage at fuse with key on?If you did not check the fuse with key on,you got a false reading.If you checked the fuse with key on,look for a bad ignition switch,or a fusible link burned into coming off a pos. terminal post where the battery cable goes to under the battery.If the blower will not work at all even on high blower,the resister most likely not the resistor.The blower motor relay is most likely the problem.

Aug 29, 2009 | 2005 Dodge Caravan

2 Answers

98 Grand Cherokee blower fan works sparatically on all settings except low


chrysler blower motors pull alot of amps replace motor and resistor card

Aug 25, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Intermittent blower speeds


pull motor ,check for burned wires onfan and bak of fan speed switch,fan could be the problem un hook fan and conect directley to 12 volts and see if varibles exsist,if so replace fan motor/look for a fan resister if all the other things check out

Jul 03, 2009 | 1999 Chevrolet Suburban

Not finding what you are looking for?
2001 BMW 5 Series Logo

Related Topics:

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Frankie B

Level 2 Expert

65 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...