Question about 1995 Mazda 626

3 Answers

95 Mazda 626 pulls to left and right while driving - almost to another lane. Replaced struts and A-frame bushing, ball joints. What is next?

Posted by on

  • Anonymous Mar 22, 2014

    Left hand drive headlights

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 83 Answers

Next is a four wheel alignment. And check tires. Even if alignment was done after repair, if tires are no good, it will pull to the side.

Posted on Jul 26, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

Alighnment it Must Be Allighned After these Repairs

Posted on Jul 26, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You should try to replace the cv joints and boots that should fix it

Posted on Aug 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Clunk noise when turning


Check the cv shaft boots, if they are torn the grease inside will have come out and now the joints inside are worn out. Worn cv joints will cause noises when turning.

Feb 20, 2017 | Ford Taurus Cars & Trucks

1 Answer

1997 Mazda 626 while turning I'm getting a vibration ( like a thumping sound) in the front end. I also pick up a heavy vibration starting about 55-60 . I have replaced the left cv shaft, wheel bearing and...


no not typically. Have you checked out the tires closely for any signs of tread separation on the tires? That could be associated with the vibration above 55.

Oct 14, 2013 | 1997 Mazda 626

1 Answer

My car started clunking in the rear near the tire, especially when I turn left


Check your top shock absorber and/or strut mounts, they may have been hammered by the many bumps and stripped out the mounting hardware on top just an eighth of an inch which will cause super loud bangs as that side wobbles up and down and hits into the Body Metal. These can get dangerous if left loose at all, my old boss said his Taurus would change lanes by itself at 120 Km/hr in the rain!

Dec 16, 2011 | 1999 Ford Taurus

1 Answer

Every time i drive into a hole my car will make this big noise just like i head iron


does it come from one of the front wheels?passenger side or driverside front?you may have a bad ball joint on one of those front ball joints.it could also be a bad strut on either front side. only an alighment can tell if it's a a bad control arm bushing or an 'a' frame bushing going bad. depending on how many miles your car has on it, and how rough it's been driven will determine the bushing life you have on 'a' frame bushings or the struts life left. i would start with the struts 1st. if you push up and dowm on the hood of your car, does it bounce up and down more than once? thats a good test for struts. if it bounces u good luck and thank you for choosing fixya.comp and down say 3 times after pushing it doen once, the struts bad.good luck and thank you for choosing fixya.com

Nov 13, 2010 | 1999 Isuzu Trooper

1 Answer

I have a 2000 mazda 626 with ball joint problems can the ball joints be replaced without replacing the control arm?


it is more cost effective to replace the entire control arm. You get new bushings as well with a new control arm, this will also tighten up the front end. $70 at rockauto.com.

Sep 15, 2010 | 2000 Mazda 626

1 Answer

After making left turn Buick Rendezvous pulls to left and after making right turn it pulls to right. What could be problem?


Ride height, struts , ball joints , contro arm bushings,
worn tires (out of round). The vehicle is 6yrs old a wheel alignment is in good order.

Apr 09, 2010 | 2004 Buick Rendezvous

1 Answer

2002 ford taurus shakes


You need to have the front end inspected for damaged steering components. Check your Tie Rod ends, A frame bushings and ball joints to make sure there isn't excessive wear or lose connections. If all of that is in good working order Drive down the road with a friend in the next lane over and have them look to see if either wheel in bouncing. If either wheel is bouncing you need to replace the struts. they are replaced in pairs, both sides. The front end will need to be aligned after you do this.

Aug 27, 2009 | 2002 Ford Taurus

1 Answer

Honda odyssey 2004


Replace the right front drive half shaft or drive shaft there are 2 drive shafts a left and a right.

Jun 06, 2009 | 2000 Mazda 626

Not finding what you are looking for?
1995 Mazda 626 Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...