Question about 1993 Isuzu Rodeo

1 Answer

Why would the fuse blow that is for engine and back up lights?

Posted by on

  • kerry littleton May 11, 2010

    they can wear out like any thing else-----does it rehappen when re placed?///

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 855 Answers

You have a short in the wiring, bad back-up light switch, bad bulbs. That is a few possibilities.

Posted on Jul 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes the 30 amp starter/HBL fuse to blow?


USA car?
what engine , gas or diesel.,what size is it?
where is fuse located, Green = 30amp
in the cab, no ,no 30amp in cab. so is below.
or in the PCD box under hood,
here is PDC,
here is fuse f15, which i think is HBL
diesel HBL is f15
gas HBL is f11

fuse 11 is 3 up from bottom right. gas only.
fuse 7 is 30amp too in pDC
and runs headlamp controls or DRL, got DRL
fuse 8 diesel? see fuse 7 answer gas.
in canada, they have DRL , daylight running lights.
we dont.
but fuse 7 30a runs that.
PDC fuse 4 30am runs ASD and if blown diesel engine dies.

HBL is fuse 15 or F11
or is Fuse 7 or 8.
which blew, ive not a clue,



http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service4f6c1760-6974-4060-8f0c-4061f5931480.jpg26005253-2mkpgvahazoelzt2oyasucxh-2-2.jpg

Dec 12, 2015 | 1998 Jeep Cherokee

1 Answer

Why does my 95 chevy 4x4 diesel keep blowing fuses when i put it in reverse


You can rule out internal transmission wires. The only thing I know of would be the reverse light wiring. You have one power wire to the neutral switch. So when the lights are supposed to come on the fuse blows the turn signal . You said you check the wiring, Did you check for continuity? High resistance cause a higher amperage draw. Also did you check the hot wire for short to ground? Try leaving the engine off. No lights on. Put it in reverse, see what lights come on. Have someone stand in back and watch as you put it in reverse. The lights should flash for a split second before the fuse blows. If any other lights come on, you have lost ground to the reverse lights.


25349764-hyer52qe2lvlylkatonhnc1i-2-2.gif

Jan 01, 2015 | Cars & Trucks

1 Answer

Why did two fuses blow making check engine light came back on


Scan for codes there a reason the fuses blew, just replacing them isn't always the answer. If they blow again you've got a wiring issue.

Jun 27, 2014 | 2001 Pontiac Grand Prix

1 Answer

Tail lights, dashboard lights


fuse , check all fuses in cab and engine bay box.
if fuse blows again, post back, (its shorted)

Nov 10, 2013 | 1995 Honda Passport

2 Answers

No reverse lights on my tiburon


You may want to check the fuses under the dash and in the engine compartment. Sometimes it will blow a fuse and cause the backup lights not to come on, beings it is part of a different circuit, similar to the low beam and high beams that are on 2 different circuits.

Oct 12, 2012 | Hyundai Tiburon Cars & Trucks

1 Answer

Ck engine light problem on 2001 Impala


Well the code is for the circuit - the computer commands the relay to turn the fan on and it doesn't happen.
The computer provides the ground for the relay.
If you have replaced the relay and the fan and the fuse still blows, I would look for a problem in the harness between the fuse box and the fan, including the ground circuit for the fan.
The fuse for the cooling fan is usually a 30amp marked "cooling fan" in the fuse box in the engine compartment.
Do you know what the 25amp fuse that is blowing is for ?

Jul 30, 2012 | Chevrolet Cars & Trucks

1 Answer

Why do I keep blowing a 20A fuse marked ECM-I?


Hi, there is a lot of stuff running on that fuse, so it may be hard to diagnose. If the fuse blows right after starting the truck, you may be able to find the short by unplugging things, putting a new fuse in, turning the key on, and then plugging things back in until it blows. Check for any wires resting on the engine or especially a hot exhaust manifold for a wire with burned insulation. Below is the diagram for the main things powered by that fuse. These include the coil, the injectors, the crank sensor, and the PCM itself. Perhaps one of the injectors has shorted. If that were the case, the fuse would not blow when the key is turned on but only after the truck is running. If you have an ohmmeter, you could check the impedances of all of them to see if one has a lower impedance. Does the truck run at all? What engine do you have? Is the engine light on? The diagram is for the V-6, but I think the wiring for the fuse is similar in the other engines. If it runs OK for a while and then blows the fuse, I would not blame the coil or the crank sensor. Let me konw what you find out.

jturcotte_1075.gif

Feb 20, 2011 | 1996 GMC Sierra

1 Answer

My brake light and interior dash lights keep blowing the fuse, every time we change it and restart the car the fuse blows again, and the engine runs great, and some times when it is ran for a while you cut...


mcdevito75 here, I would try to isolate the problem with the fuse blowing, ---- sit in the car and step on the brake, without the car running see if the fuse blows, the just put the key to on not strat just on see if the fuse is blow, if it is you may have a problem under the dash, if not, now with the key just on no start, step on the brake see if that fuse is blow, if so you may have a problem at the brake light switch under the dash or at the brake lights themselves at the back of your car, a bad ground, loose or broken wire, inspect if you can. The hard or no starting after you drive for a while could be related or a problem with the ignition coils or ignition module. In any event have your local auto re[pair shop check these items out for you, a short could cause real problems in your car.

Jun 02, 2010 | 1997 Pontiac Grand Prix

2 Answers

I have f-250 diesel. keeps blowing fuse #22,glow plug controller. what might be the problem


You should start with the glow plug relay/timer.Check it to see if may be shorted.Remove the smaller wires going to it and turn the key back on,if the fuse does'nt blow then replace it,if it does then you need to unplug the fuel preheater in the filter housing and try the key on thing again,pretty sure it's one or the other.

Dec 08, 2009 | 1995 Ford F250

Not finding what you are looking for?
1993 Isuzu Rodeo Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...