Question about 2000 Dodge Durango

1 Answer

99 dodge durango is skipping 2nd gear replaced pressure sensor and selinoid still skipping

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,187 Answers

You may have a problem on the valve for the second gear. Ot could be clogged by debris and may need cleaning or may need replacing.

Posted on Jul 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dodge Ram 3500 skips from 1st to 3rd gear, had rebuild after still the same issue. Any advice?


Governor pressure controls the 1st and 2nd shifts. After that is the 3 and 4 solenoids. you would need to look at the pressure when driving(takes a scanner). pressure is 20 to 30 PSI from 1st to 2nd, depends on acceleration. After that the pressure will jump to 100+ psi. Did you replace the governor solenoid and sensor? They are on the passenger side of the transmission and sit in a block that detaches from the valve body.

Sep 22, 2016 | 2005 Dodge Ram 3500

2 Answers

99 Dodge Durango 5.9l V8 turning over but not starting. Strong smell of gas from air intake. Plugs sound like sparking. Fluids good and clean air filter. Any ideas?


Cam Sensor Failure Causing no Start or Stalling : Dodge ...

repairpal.com > Problems > Dodge > Durango
Dodge Durango Cam Sensor Failure Causing no Start or Stalling. ... On the 4.7L V8engine, the Camshaft position sensor failure can cause the engine to crank but not start or it can ... On the 5.9L V8 engine, rerouting the ignition coil wire and spark plug wires can help solv. ... 1999 Dodge Durango ... Drove good till put gas.

Aug 05, 2015 | Dodge Cars & Trucks

2 Answers

Shifting problems 02 Dodge Durango 46re


shift solenoid needs to be replaced or the speed sensor

Oct 18, 2012 | 2002 Dodge Durango

1 Answer

On my 99 dodge durango the check engine light comes on and the oil pressor falls and the engine makes knocking noise what do i do to fix the problem


  • First check the oil level and make sure it is full.
  • Sounds like your Oil Sending Sensor is Failing. What happens when it fails is the oil pressure drops and the light goes on. You can test it by pulling the sensor and putting a gauge on it. If you have 6 PSI or better in park and 55+psi in gear then it is good. When the pressure drops so to does the circulation. Drive it to long like that and you risk seizing your engine. Replace that sensor immediately if the pressure is not as it should be.
  • This can also be a weak oil pump.
  • I recommend checking in the order I listed. It is more than likely one of them.
Good luck to you, Regards, Tony

May 17, 2011 | 1999 Dodge Durango

1 Answer

What is MIL code 1757 on 2001 Dodge Durango?


governor pressure above 3psi in gear with 0mph
possible causes
solenoid pack connector 5v supply circuit open
sensor signal circuit shorted to ground or shorted to voltage
governor pressure sensor defective
transmission fluid burnt or pan has debris
valve body valve sticking or defective
pcm defective

Jul 13, 2010 | 2001 Dodge Durango

1 Answer

2000 Dodge Durango - P1757 GOV Pressure Not Equal


I have had to replace the governor on those dodge transmissions, and there is a filtering metal mesh screen around the governor inlet port that seems to always get plugged up with small metal shavings. The governor is located under the transmission pan to the rear of the main valve body.

May 05, 2010 | 2001 Jeep Grand Cherokee

1 Answer

Runs first gear to max rpms before shifting.


You probably have a bad governor pressure sensor and solenoid.The pressure sensor is what normally goes bad ,but from vast experience,i replace both of them together and change fluid and filter.

Aug 09, 2009 | 1999 Dodge Durango

1 Answer

Have a 2001 Dodge Durango wont shift out of 2nd gear


IT'S PROBABLY EITHER THE INPUT OR OUTPUT SENSOR ON THE SIDE OF THE TRANS!!!

Jul 01, 2009 | 2004 Dodge Durango

1 Answer

1998 dodge durago transmission will not shift into 2nd gear


It may be the torque converter clutch circuit. Do you have a check engine light on?

May 07, 2009 | 1998 Dodge Durango

Not finding what you are looking for?
2000 Dodge Durango Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...