Question about Kia Sedona

1 Answer

Belt snapped and I need a schematic to install new one.

Posted by on

  • gabrielgo594 Jul 26, 2009

    Haven't done it yet, but seems simple enough.

    Thanks much for your assistance.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,170 Answers

Here is a vedio on changing Kia Sedona Belt :

Instructions :
YOU START OUT BY LOOSENING THE ALTERNATOR IT HAS A TENION SCREW IN END A BOLT ON FRONT OF THE TENSION BOLT THE A BOLT ON THE BACK AND ABOLT ON FRONT NEAR THE EENGINE THE ALT. IS READY HAVE BELT REMOVED ANDREPLACED THEN JUST TIGHTEN EVERY TTHING BACK UP ON THAT SIDE. THEN MOVE TO THE POWER STEERING BELT IT WILL BE A LITTLE MORE HARD BUT NOT BAD SUGGESTING CUT THE POWER STEERING BELT OFF THAT WILL MAKE IT EASIER TO FIND THE 5 BOLTS YOU WILL HAVE TO LOOSEN YOU WILL HAVE 2 ON THE TENSION JUST LIKE THE ALT. THEN ONE BEHIND THE PULLEY AND 2 BELOW THE PUMP BELOW THE PULLEY ONCE YOU HAVE THOSE LOOSE YOU CAN PUT THE BELT ON AND TIGHTEN EVERY THING BACK UP. TOOLS YOU WILL ASET OF SOCKETS 6 POINT WITH EXTESION A SET OF 45 DEGREE WRECHES 6 POINT.

Posted on Jul 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would make a new fan belt snap


2 main reasons.
1. the belt is being over tighten
2. the belt is miss aligned / rubbing against some thing (check the pullies)

Nov 18, 2014 | Citroen Berlingo Cars & Trucks

1 Answer

Scamatic for a 2008 Jeep Liberty Belt?


2008 Jeep Liberty Belt Anon, Schematic belt.Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Install Replace Serpentine Belt Tensioner Idler Pulley 3 7L 2004 13...
2008 Jeep Liberty Serpentine Belt Removal
2008 Jeep Liberty Belt routing Google Search

Jun 22, 2014 | 2009 Jeep Liberty

1 Answer

2008 PT Cruiser Wiring schematic for Power seat


There's a red and lite green wire going to the seat motor, and a red and dark green going to the seat heater.
Do you know where the wire popped off at ? Or what no longer works ? It could be something with the seat belt sensor or the air bag sensor too.

Jul 19, 2013 | 2008 Chrysler Pt Cruiser

1 Answer

2001 lincoln town car belt routing


Continental And Mark VIII With The 4.6L Engine
WARNING
Do not allow the drive belt tensioner to
snap back as damage to the drive belt tensioner or personal injury could result.


  1. Rotate the drive belt tensioner clockwise with a breaker bar installed in
    the 3?8
    inch square hole in the drive belt tensioner.
  2. Lift the drive belt over the idler pulley flange and remove the drive belt.
    To install:

  3. Following the schematic on the decal under the hood, position the belt over
    the pulleys, except the idler pulley.
  4. Rotate the tensioner as described above and install the belt on the idler.
    Ensure that all the V-grooves make proper contact with the pulleys.

Town Car With The 4.6L Engine

  1. Install a breaker bar in the 1?2 in. square hole in the automatic tensioner arm.
  2. Rotate the tensioner away from the belt with the breaker bar.
  3. Lift the old belt over the alternator pulley flange and remove it.
    To install:

  4. Position the new belt over all the pulleys, except the alternator pulley,
    rotate the tensioner as described above and install the belt on the alternator
    pulley. Refer to the belt routing illustration on the sticker located at the
    front of the engine compartment. Ensure that all the V-grooves and all the ribs
    on the belt properly contact the grooves on the pulleys.
  5. Rotate the tensioner toward the belt and remove the breaker bar.





    Fig. 1: Make sure the belt makes proper contact with the pulley
    grooves
    84171049.gif






    Fig. 2: Accessory drive belt routing - 4.6L engine
    84171050.gif


Town Car And Mark VII With The 5.0L Engine

Sep 23, 2010 | 2001 Lincoln Town Car

1 Answer

Change a serpentine belt on a 97 lincoln


3.8L Engine
  1. Insert a 1/2 inch flex handle in the square hole in the tensioner. The tensioner has a square hole cast into the rear of the tensioner body directly behind the pulley. Rotate the tensioner clockwise and remove the belt from the pulleys.

NOTE As an alternate method, a 16mm socket can be placed on the tensioner pulley bolt and rotated clockwise to remove the belt.

To install:
  1. Following the schematic on the decal under the hood, loop the drive belt over all the pulleys except the alternator pulley.
  2. With the belt installed properly on all except the alternator pulley, rotate the tensioner as described above and install the belt on the alternator pulley. Ensure that all the V-grooves make proper contact with the pulleys.

4.6L Engine
WARNING Do not allow the drive belt tensioner to snap back as damage to the drive belt tensioner or personal injury could result.


  1. Rotate the drive belt tensioner clockwise with a breaker bar installed in the 3/8 inch square hole in the drive belt tensioner.
  2. Lift the drive belt over the idler pulley flange and remove the drive belt.
To install:
  1. Following the schematic on the decal under the hood, position the belt over the pulleys, except the idler pulley.
  2. Rotate the tensioner as described above and install the belt on the idler. Ensure that all the V-grooves make proper contact with the pulleys.

Apr 23, 2010 | 1997 Lincoln Continental

2 Answers

Vw lt46 1998 would it damage valves if timing belt


yes it will and most likely put a hole in the piston and snap the cam shaft if the engine is doing any more than idle speed, if it breaks at idle you may be lucky and just get away with a few bent valves but if im honest ive never seen anyone be lucky with one the normaly require a new engine. also worth changing the water pump at the same time as these do seize and will snap the new cam belt ! the only belt you can get away with leaving is the pump belt if this breaks no damage is caused the engine will just cut out ! however you will need to pretty much remove it after fitting a cambelt to set the timing so its pretty pointless no to change it

Apr 15, 2010 | 1997 Volkswagen Eurovan

1 Answer

My seat belts actual belt snapped and I was wondering how I could remove the belt so I may install a new one?


just remove trim and replace as you take out..make sure you replace all new bolts with the new belt...

Mar 05, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

Timing belt snapped on a 1.4 lanos,will it need a


Just a new belt--the valves on gas engines do not hit the piston like on diesel(this is because diesel has very high compression)

Jul 11, 2009 | 2001 Daewoo Lanos

1 Answer

Need diagram/schematic for serpentine belt replacement


Should be a tag on the core support somewhere that shows a diagram how to install your belt,usually its right on top where the radiator bolts to core support,open hood look down on top of support or its on the inside of hood open hood and look up see if theres a tag with a diagram of belt installation

Mar 22, 2009 | 1998 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...