Question about 1984 Jeep CJ7

1 Answer

How to remove rear axels - 1984 Jeep CJ7

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

Welcfome to fixya.Here is the priocedure if you need anything just go to www.collisionrepairadvice.com

  1. Raise and support vehicle. Support at frame behind front springs.
  2. Remove front wheels.
  3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
  4. Disconnect connecting rod at steering knuckles.
  5. Disconnect shock absorbers at axle housing.
  6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
  7. Disconnect breather tube at axle housing.
  8. Disconnect stabilizer bar link bolts at spring clips.
  9. Remove disc brake calipers, rotors and brake shields.
  10. Remove U-bolts and tie plates.
  11. Support axle assembly with suitable jack to relieve spring tension.
  12. Loosen rear spring shackle to spring attaching bolts.
  13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
  14. Remove axle from under vehicle.
  15. Reverse procedure to install.

Posted on Jul 26, 2009

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

468 Chevelle
  • 81 Answers

SOURCE: how to remove rear axel to replace rotor rear in 1989 f superduty

Rotor just pops off of hub.

Posted on Mar 27, 2009

  • 161 Answers

SOURCE: how too remove rear axel horsehoe clips too remove

In order to remove the axle, you need to go in through the rear pumpkin. Take the back plate off the rear pumpkin, then you will see where your axle comes in through the sides. Go back to the outer end of the axle, (where the tire goes) and push inward on the axle. It shouls move in about 1/2" or so, just enough to remove the clip. The clip should fall out easily if it is turned in the 'down' position. Then you will need to remove the pins that run through the axles themselvs, and the axles should pull right out to the sides.

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't remove rear axel yoke


im not sure of your question. ?
that is a drive shaft and or propeller shaft, off
fist start by saying, what you are doing? we dont know.
What is the goal, ????
my guess is, removing the axle carrier from the axle housing?
you must remove both axles to do that.
here is a 2004 , axles being pulled. (im guessing what you are doing)
http://www.fixkick.com/axles/axle_rear_R&R.html

Apr 19, 2013 | 2000 Suzuki Grand Vitara

1 Answer

I have 2001 Chev Tracker, Oil started to run out of the Right side break drum. Removed Drum and foud oil all over the breaks. Tried to remove the Axel by removing the four nuts off of the backing plate,...


fror fixing the brakesw take the other rear wheel off and duplicate what u see. to get the axel out u must first remove diff cover in center of rearend then u will see a clip for each side axel remove clip and axel will slide out. good luck fron 1 to 5 being difficult its a 3

Jul 21, 2010 | 2002 Chevrolet Tracker

1 Answer

Leaf spring replacement


Yes but you need two thumbs. Jack the truck and support it on the frame ahead of the axel so the axel can hang on its own weight. Remove the bolts and mount to the bad spring - remove the axel mount first, Let the axel sag and put something under the tire to help hold it. Remove the spring mount bolts to the frame and lower the spring out the rear. reinstall is the reverse --- BUT --- the new spring may not fit right in the spring mounts. Mount the front bolt first and then the rear - you may have to use a pry-bar and force the spring into the rear mount.

May 08, 2010 | 1997 Nissan Pickup

1 Answer

The axle from a jeep 4x4 is broke , both axles, how do i take out the rest of the parts?


The front axel is a two piece assy. remove the 4wd
shift moter from the axel housing. Once the moter
and fork are off , remove outer axel.To remove inner
axel, remove differential cover and let it drain.
There is a C clip on the axel, remove it and work the
axel out through the axel tube.(if it is broken)
To remove the rear axel. Remove diff. cover and drain.
Remove the pinion lock nut(or spring clip) and slide
back pinion shaft. Remove retaining clip from axel
and remove axel. To remove broken piece I use to
use a length of an old whip antenna, to push it out.
If you can find a piece of heavy gauge wire to push
it out.(a plumbers snake may work)Also only have
one axel at a time out of either housing, this will
make it easier to reinstall the axels.
I hope I was of some help. Good luck.

Jan 30, 2010 | 1995 Jeep Grand Cherokee

1 Answer

How to remove rear axle 03 chevy silverado


You will have to remove the rear end plate off of the back of the rear end. Then turn the carrier untill you see a big silver pin that goes through the spider gears. Those will be 4 small gears in the rear end carrier. If you look at the right side of the carrier were the pin goes through it you will see a small bolt head, That bolt goes through the carrier and holds the pin in place. Remove that bolt then reach up in the rear end housing and push the pin towards you untill it comes out. ( DO NOT TURN ANYTHING AFTER YOU REMOVE THE PIN) are the spider gears will fall out.


Now get someone to push the axel in while you are looking at the 4 small gears in the housing, when they push the axel in a C-clip will fall off the end of the axel and into the rear end, You will see it fall out. Then just pull the axel out.



When you put the axel back in, push it all the way in then slide the c-clip over the end of the axel and then pull out on axel and that will hold the clip in place untill you put the big long pin back in the carrier. I hope you understand, just watch what you are doing. GOOD LUCK.

Oct 09, 2009 | 2003 GMC Yukon

1 Answer

Rear Axel Seal Leaking, How do I pull the axel to repair?


You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.

May 22, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Rear Axel Seal


Wheel, brakes etc that are in way of pulling axle out have to come off. Drain rear end fluid, remove rear housing cover, remove bolt that holds pin in differential, remove differential pin, push in slightly on axle to remove "U" clip that holds shaft in, then slide shaft out. replace seal. Reverse procedure for re-install & fill with gear lube. If any questions, get back to us.

Apr 16, 2009 | 2002 Ford Mustang

1 Answer

85 cj7 rear axle removal


Do you have bolt in axels? or are they held in with C- clips? If its bolt in axels you need to remove the bolts, and you may need an axel puller to get them out. If its got C- clips rear cover on rearend has to come off, and pin has to be removed to get C- clip out to get axel out.

Apr 03, 2009 | 1986 Jeep CJ7

1 Answer

Rear axle seal replacement


Drain axel of Fluid, Roemve Diff Cover (Push IN on Axel to reseal at Wheel side) Remove KEEPERS From Insied END of axel then Pull OUT on WHEEL END of Axel. use Proper Seal removal tool to remove seal. Also Use PROPER Install tool for SEAL INSTALL Reverse Procedure to Install. In hopes this helps you Out.
Please RATE Me Also LoL Thank You.

Mar 24, 2009 | 1999 Ford F150 Regular Cab

1 Answer

Replace rear axel bearing on 4x4 5.3 Litre gas engine


Loosen differential cover and let oil drain. Remove cover, remove U lock from axel. Pull axel out. Remove bearing seal then bearing. Install new bearing, seal and reinstall axel. Reinstall U lock and new cover gasket. Fill with 75-90wt gear oil. Now I know that sound pretty straight forward. But there are some things to remember. The U lock can be difficult to remove sometimes. The most important thing is the seal, you will need to make sure it gets seated correctly and not torn when installing axel.

Jul 12, 2008 | 2000 GMC New Sierra 1500

Not finding what you are looking for?
1984 Jeep CJ7 Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...