I have a 2007 Ford Focus ses 2.0 is the Rasmussen range sensor located on the upside of the transmission

SOURCE: ford focus 2007 bonnett release?

it should be in the upper left of the inst panel

Marvin

• 85242 Answers
• Posted on Jan 05, 2009

SOURCE: 1999 ford f350 engine code P0705 transmission range sensor warnin

P0705 - Trans Range Switch Circuit

Get under the truck and look where the trans shift linkage connects to the trans, there is a post that comes out of the trans, on that post u will see a large switch with multipile wires connected to it, that is the range selector switch, you need to remove the shift arm and a couple of bolts to remove the range switch, it is adjustable, u will see the slots, make sure u put the new switch in the same position as the old one or the truck may not start.

SOURCE: 1996 ford contour transmission range sensor

Transmission range sensor and neutral safety switch are the same thing (when you go to buy the part). It's at the top of your transmission. You'll see the shifting cable connected to it. Here are the instructions for adjustment:
Shift Control Linkage
The transmission shift linkage adjustments must be performed in the order in which they appear.

Column Shift

Place transaxle range selector lever in (D) (OVERDRIVE) position or D (DRIVE) position on vehicles equipped with a transmission control switch (TCS). A weight of 1.4 kg (3 lb) should be hung on the transaxle range selector lever to ensure the lever is located firmly on the (D) (OVERDRIVE) or D (DRIVE) position on vehicles equipped with a transmission control switch (TCS) detent.

Loosen manual control lever-to-control cable retaining nut.

Move transaxle manual control lever to OVERDRIVE position or D (DRIVE) position on vehicles equipped with a transmission control switch (TCS), second detent from most rearward position.

Tighten retaining nut to 17-23 Nm (13-17 lb-ft). Check operation of transaxle in each transmission range position. Make sure that park mechanism and transmission range (TR) sensor are functioning properly.

Floor Shift

Position transaxle range selector lever in DRIVE position against rearward stop. The floor transaxle range selector lever must be held in the rearward position using a constant force of 1.4 kg (3 lb) while linkage is being adjusted.

Loosen manual control lever-to-control cable retaining nut.

Move transaxle manual control lever to DRIVE position, second detent from most rearward position.

Tighten retaining nut to 17-23 Nm (13-17 lb-ft).

Check operation of transaxle in each transmission range position. Make sure that park mechanism and transmission range (TR) sensor are functioning properly.


To take it off, it's a couple of retaining bolts and a wiring harness.

SOURCE: I have a 2007 Ford Focus 1.8 Sport.

There are child locks on the rear doors.If you open the rear door and look at the lock on the door, there are 2 ways it can go .
So if a lock is working you should be able to open from the outside or if not the door can be opened from inside and outside.

Wayne Fellows

• 262 Answers
• Posted on Mar 27, 2010

SOURCE: need to know location and how ro remove a

1. Remove the Battery
2. Remove the battery tray. You need to do this to access the TRS(transmission Range Sensor) If its 2.5 liter you need to also remove the air cleaner, and the battery box bolts(on bottom of box)
3. Detach the battery positive cable push pin from the battery box.

1. Lower the vehicle.

1. Disconnect the battery junction box (BJB).
   1. Remove the cable ties.
   1. Unclip the BJB.
• Position the BJB to one side.

1. Pull the horn and front fog lamp wiring harness through the hole in the battery tray.
1. Detach the wiring harness from the pin-type retainers in the battery tray.

1. Disconnect the TR electrical connector.

1. Remove the bolts.

1. Remove the TR sensor.